Having problems with your Dyson Vacuums ?

Brush won't turn belt is good is the clutch bad

Answers :

Have you turned on to see if the area where you put the belt on is rolling?
if it is you probably need a new brushroll . check the edge of the brush roll and see if any plastic is missing within the removable metal piece by where the band should be on the roll.
Repair Help & Product Troubleshooting for Dyson Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Model DC14 beater brush doesn't turn. belt from motor turns but doesn't turn beater brush belt from clutch . Is clutch bad??

You might need to replace both belts. You can get them here:DC14 Replacement Belts ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Brush won't turn belt is good is the clutch bad

Have you turned on to see if the area where you put the belt on is rolling?if it is you probably need a new brushroll . check the edge of the brush roll and see if any plastic is missing within the removable metal piece by where the band should ... Dyson Vacuums

Bissell 9200 pro heat carpet cleaner , brushes won't turn, both side belts are good. bad brush motor? or brush moter belt?

... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a DC14 with a bad belt to the roller.How do I remove the clutch that operates the belt to turn the roller. I am holding the assembly that houses the clutch and all screws are out, it appears the red knob that engages the drive to operate the roller brush must be removed. Please advise and how. Thanks, John.......[email protected]

You need a special tool to remove the clutch. Contact the Dyson Helpline so that they can refer you to an authorized Dyson dealer in your area who would have such a tool and who can fix it for you. The alternative is to purchase a tool and visit YouT ... Dyson DC14 Bagless Upright Cyclonic Vacuum

Hoover windtunnel U6425-900 the brush roll is not turning. Both belts are in good shape, I cleaned the brush roll and it is free of debris, the setting is on carpet and the brush roll still will not turn. There is a "burning rubber" smell when you attempt to push the vaacum forward a few times. The small belt does not seem to be pulling properly but appears to be in good shape.

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The vacuum sucks good, but the brush on the bottom wont turn, and the belt seems tight

Even tough the belt is intact it still might need to be replaced. Here is a replacement:Dyson DC14 Belt and Manual ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a

... Bissell ProHeat Deep Cleaner Upright Vacuum

The brushes wont turn,but it has good suction for the hose

If the belt seems to ok, you may need to order a replacement clutch assembly. These are not that expensive and can be ordered through dyson or possibly online. Switching from bare floor to carpet while the motor is running is really stressful on th ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?

Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Have a Hoover model S3670 and the beater brush no longer spins. Have checked the beater belt and it is good, did find out that the light bulb in the unit was bad. Any suggestions on how to test the motor that drives the belt or determine the reason the beater brush is not working?

I usually test the motor with a cord with alligator clips on the wires, and attach them to the black and white wires on the motor ( remove the belt first ). A very common problem with this model was a short circuit developing in the short cord that r ... Hoover Vacuums

The brush roller will not turn. checked the belts, checked the brush roller gears and they are good too... the motor is not turning .. could it be a switch somewhere?

... Electrolux EL5020 Vacuum

Brushes wotn spin,belt not broken,cog that drives the belt is not spinning.When I turn the brushes manually I can occaisionally feel it grabbing for a a brief second.Could the motor be bad? Is there a way to test the motor.Tahnks

The motor is bad and this is a common problem with this machine. It is engineered very poorly. I would take it back and get a Dirt Devil Platinum Force machine. They have a great track record. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge

... Vacuums

I got new belts but the brush wont turn

Make sure the vacuum is on the carpet setting..the brush won't turn on the hard floor setting.. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Brush wont turn loose belt, new belt no help

May need to clean or replace beater bar. take brush out of vacum hold on the end and try to turn brush ... Vacuums

I have an oreck xl and the vaccum wont hardly push. Is it the belt? The brushes aren't turning when I lay it on it side. How do you replace the belt? If you can give detailed instructions I would so appreicate it . Thanks

On the side of the head you'll see a removable plate with one screw. Remove the screw and slide the plate towards the front until it's off. You'll see the belt. ... Oreck XL21 Bagged Upright Vacuum

I have a dyson dc07 upright which no longer picks up lent and hair. The roller brush is not spinning when the vacuum is turned on. How can I tell if it is the belt that needs to be replaced or the clutch and belts?

Need replaced Clutch Assy and Brushbar \015\012\015\012Clutch Assy part no:900252-04\015\012\015\012Brushbar Assy part no:904174-01\015\012\015\012try cleaning all Hose\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Bissell Upright Proheat 2x and the dual power brushes wont rotate. I went to replace the drive belt and noticed the drive shaft does not turn when power is turned on. What shall I check next?

Is there a light that comes on when you "turn the power on." If there is no light, and the unit is plugged in, how do you know there is current going to the motor? Sounds like there might be a break in the cord. Examine the cord near the plug end ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hi my dyson dc07 animal has suction but the brush bar wont turn. If I turn it on there is a horrible noise. The belt is still fine

The belt is probably worn or stretched. When this happens the belt won't turn\015\012the roller brush when it is against the carpet. Here is a link for the\015\012manual and links for the belt ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Beater brushes not turning on the wife's Hoover Steam Vac model F5905-900. Found one prior ''solution'' stating that it sounded like the belt was bad. That was my original thought, but on checking schematics and trying to find part numbers at Sears Parts Direct and at Hoover, it does not appear the F5905-900 steam vac HAS any belts to begin with. What's next??

This one I can tell you about from personal experience with that generation Hoover Steam Vac. After using it about 7 or 8 times my brushes stopped turning also.I disassembled it (kind of like disassembling a Chinese puzzle box) and found ... Hoover F5905-900 Vacuum

The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th

... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc

... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.

... Kirby Ultimate G Bagged Upright Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn

Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 1.2538 seconds