Having problems with your Dyson Vacuums ?

My Dyson does not pick up the dust and dirt if I take the pipe off to clean the stairs, there is no suction, but as an upright it is fine.. can you help

Answers :

Repair Help & Product Troubleshooting for Dyson Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Dyson does not pick up the dust and dirt if I take the pipe off to clean the stairs, there is no suction, but as an upright it is fine.. can you help

... Dyson Vacuums

When using my vacum upright its very low in suction, it used to be so powerfull that it lifted my carpet slightly....when using the tools section its as strong as it should be please help, ive cleaned it out but still loss of suction in upright position, from mrs richmond

Check the following items:\015\012\015\012* The bag and connection - change it if it's full\015\012\015\012* Turn the vacuum over and inspect the beater bar area for any clogging. You may have to remove the bottom plate to ... Vacuums

My eureka optima upright bagless vaccum has VERY low suction using the floor part. the hose has excellent suction. i removed the little translucent door underneath and there were no blockages, i cleaned the brushroll thoroughly and that hasnt helped either. i know this probably isnt recommended but i turned it on to the floor setting with the brushroll off and stuck my fingers up the intake as far as i could, the suction was good further up but it just seems to stop down at the base. because i s

I will try and help here. Is the sole plate on the bottom of the vacuum complety on and there are no visible cracks along the seam where it meets the body? This is the usual cause for this. Onc you take of the plate to access the roller and brushes, ... Eureka 431A Optima Bagless Upright Vacuum

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga

I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums

It seems to be blowing dirt around not suking but when removing the attachment to clean stairs etc the pipe works fine have washed filteR ? SLIM UPRIGHT DC ALLERGY 18. Have cleaned out filter emptied cylinder taken any bits of cotton or hairs from brushes..........

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula

There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

My DC07 Animal Bagless Upright Cyclonic Vacuum has a small attachment for vacuuming carpeted stairs. This attachment is currently not spinning its internal brush necessary to pickup the dirt on the stairs. The rest of the vaccum is working fine. The suction cap on this attachment is pulled out, as it should be. I have checked the vacuum over thoroguhly and there are no bloackages anywhere.

Make sure to extend the wand straight up and completely out of the handle and watch that you don't kink the hose. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Took my Hoover Steam Vac apart to clean it and now it won't **** up the water but was working fine before I got the bright idea to clean it. Took four screws out but did not touch the motor. It puts out water and the brushes rotate but no suction? Thank you for your help, Cathy

The suction is created by the motor and is pulled to the motor through the flexible hose. The hose could have pulled off at one end or it could have torn in a spot where there is more pull on the hose like when you lay the handle down to empty dirty ... Hoover F7431-900 SteamVac Vacuum

Suction perfect when in upright position, but when tilted to actually clean there is total loss of suction - cannot see blockage anywhere. Thanks for your help.

If you are confident there are no blockages, look underneath, where the brush is, and you will see a short length of reinforced clear plastic hose. This often develops a split which results in loss of suction. You can pull the hose off at the motor e ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Kenmore upright progrssive intell clean. For some reason it isn't sucking when I use it to vacuum. When I use attachments they work fine, but when I plug the hose back in after using the attachments and turn it back on it makes a weird noise and I can feel air blowing out of the back. Can you help me resolve this problem?

You have the answer and just don't know it. You are there so keep looking. Somewhere between where the suction hose connects with the lower hose and the power-head. There is a blockage, you may need to turn the unit upside down and look there or try ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

My Dyson upright is not picking up like it used to. The suction from the tools is very strong and the beater bar is turning and clean. Please help

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Kenmore upright progrssive intell clean. For some reason it isn't sucking when I use it to vacuum. When I use attachments they work fine, but when I plug the hose back in after using the attachments and turn it back on it makes a weird noise and I can feel air blowing out of the back. Can you help me resolve this problem?

Open this manual to page 18 and clean all the filters listed to restore air flow.http://www.managemylife.com/mmh/lis_pdf/OWNM/L0908343.pdf ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Vacuum works fine when using the attachments, but as soon as we try to use it in it's normal upright position it does not work. We have cleaned all filters and removed debris from roller, but nothing has helped.

Greetings,\015\012\015\012There could be a few things that would cause your Dyson to do this. I will give you detailed step by step instructions along with pictures on how you can diagnose this problem. \015\012\015\012Po ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Miele Vacuum cleaner MedicAir 5000 Plus. Recently the Dust Bag Indicator bar is full during normal cleaning and consequently the suction power is much less. I replaced the dust bag, engine pre-filter and Hepa filter but no change. When i remove the hose, the Indicator is normal, but when i attach the hose, wand, head, the indicator is full. I checked the hose, wand, head but can't see any blockage and when i blow with my mouth it seems fine. Can anybody help? thanks!

... Miele Vacuums

No suction I have a bissell turbo heat upright carpet cleaner. I've used it once and loved it. I cleaned one room today and realized it wasn't sucking up the water and is louder than before. Please help.

If this is a 9400 series check and make sure the red flap in the lid of the dirty water tank is not closed. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Ive changed the filter and checked the hoses but vacuum doesnt pick up ...when its on the dust is being blown out the bottom of the vacuum....i took the canister off to test the suction its fine...also cleaned the filter ...help!

Have you check the roller brush and drive belt? It may be your belt has broke or is slipping and therefore not turning the brush.\015\012Turn on machine and power head see if brush is turning if it is put a small amount of pressure on the rol ... Kenmore Vacuums

Sebo upright barged hoover- good suction using hose, brush wont turn, sounds fine when running, nasty wineing noise when stopping?? help!! i love my hoover, have checked for bolckages....

The real clue seems to be the brush is not turning, a bad belt is possible or a blockage at that head, if you cannot get the brush moving the rest does not matter. ... Sebo Felix Classic Bagged Upright Vacuum

Filters all seem clean and clear, suction is fine,but loud noise

Sounds to me it could be tha fan impellor.\015\012This is vac's etc... email us if you need to.\015\[email protected] ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o

Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hi...there is no suction in my upright's hose...there is suction when regular carpet cleaning but when I put it in an upright position and take the hose out there is extemely light suction.

... Miele S7210 Bagged Upright Vacuum

My vac has lost suction. When I vacuum it picks up very little, but when I remove the wand hose it has good suction. We have cleaned both filters, checked for blockage in all hoses & cleaned the beater bar brush. All to no avail. Is it the motor? Or is there a blockage deep in the vac somewhere? We're debating repair versus buying a new one. Hope you can help. Thanks.

Hi there,Sorry to hear you're having a problem with your DC14. Since you say you've already washed the filters and checked for blockages, it's probably best if you get in touch with us so we can run through some simple troubleshooting ste ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

No suction i have a bissell lift off revolution vacuum. I have cleaned all the filters and emptied out the canister made sure that the hoses are not plugged but it will not pick up unless you use the hose. the floor brush is clean and still no suction coming from under the vacuum... could you help me please

Is there a blockage in the small hose in the bottom of the machine \015\012take of the pod and you will see the small hose, \015\012Is the main hose pushed into the bottom housing ... Bissell 37603 Upright Vacuum

I am wondering how I can clean the inside of my bissell spotlifter powerbrush hand held cleaner? I want to clean the part where you suction up - it is full of gunk and hair and I can't figure out if it comes apart or not so I can clean it. Can you help?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=49876&thid=506980\015\012I am wondering how I\015\012Posted by carriespets on Apr 12, 2008\015\012I am wonde ... Bissell SpotLifter 1716 Bagless Handheld Vacuum

No Suction I have a dc18 dyson and it had lost suction from the main hoover and the hose part. If you remove the dust collection part there is suction from the hole behind that part. I have cleaned all part to this hoover but the problem is still there. Any help would be apprieciated. Thanks

Filter removal step 1Turn power off and unplug the machine.\015\012\015\012To remove the washable filter: Rem ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

My Bissell 9200 is not sucking the water into the dirty water resevoir. 1. The gasket on the clear-view seems fine. 2. The suction power just doesn't seem powerful enough (feeling with my hand). 3. The brushes turn fine and belt is fine (not sure if that even matters for this issue). Any help appreciated. Thanks, - Matt

Disassemble all lines and check to see if all O rings are installed. If cracked missing or stretched out of shape no suction will be provided ... Bissell 9200 Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0780 seconds