Having problems with your Dyson Vacuums ?

HELP!!dyson vacuum only 2 years old model DC18 runs but has lost suction on the wand side of the vacuum does anyone have any suggestions for us??


Answers :

Its the ball cradle assembly. There is a little clip that changes the direction of the suction. that clip breaks all the time and causes the internal direction valve to stay in one position. unfortunately dyson doesnt sell these parts separate, you will have to purchase a new cradle assy. let me know if you need a part #
Repair Help & Product Troubleshooting for Dyson Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

HELP!!dyson vacuum only 2 years old model DC18 runs but has lost suction on the wand side of the vacuum does anyone have any suggestions for us??


Its the ball cradle assembly. There is a little clip that changes the direction of the suction. that clip breaks all the time and causes the internal direction valve to stay in one position. unfortunately dyson doesnt sell these parts separate, you w ... Dyson Vacuums

I have a DC17 which is only one year old. Today I lost suction and called for assistance. A Dyson technician told me to pull off the wand and see if it is clear. It was clogged so cleared out the obstruction. My filter was cleaned more than 24 hours ago. The vacuum still has no suction. Is it dead, any other suggestions. Please help.


Take the hoses off and give them a good shaking.\012or get a long piece of stiff wire and gently poke through the obstruction. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

No suction vacuum working fine and suddenly, no suction at all....what could be the problem? no suction through the machine from either the wand or the floor/brush side


Sucked up a sock?? No seriously.. it may be as simple as that or that an on board filter is clogged. Check your manual for all filters and Hepa/screens and others. Also, is the unit making any odd noises since the non -suction scenario? Whining or s ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My vac has lost suction. When I vacuum it picks up very little, but when I remove the wand hose it has good suction. We have cleaned both filters, checked for blockage in all hoses & cleaned the beater bar brush. All to no avail. Is it the motor? Or is there a blockage deep in the vac somewhere? We're debating repair versus buying a new one. Hope you can help. Thanks.


Hi there,Sorry to hear you're having a problem with your DC14. Since you say you've already washed the filters and checked for blockages, it's probably best if you get in touch with us so we can run through some simple troubleshooting ste ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Eureka Pet Pal and it seems to have lost suction on the main part of the vacuum. It looks like it sucked something up before it happened so I'm fairly sure that the tube is clogged but I don't know how to take the vacuum apart so that I can clear it out. Is there anyone out there than can help me figure it out?


... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

We bought our Kirby less than 5 years ago and lately are not happy with it....it keeps breaking. The warranty has expired and our biggest complaint is that it has lost it's suction power. All the contents stay in the hose when I vacuum out the car or upholstery and it does vacuum well at all. The Kirby store quoted us over $200 to fix/ service it. Apparently this is not covered in the free yearly maintenance which we just had done. Any suggestions?


\012 Hi there,\012Well I do have a suggestion though you may not like it use it as a boat anchor.....no no I am just kidding. I have sold vacuums for 20 years and Kirby has b ... Kirby Ultimate G Bagged Upright Vacuum

Our Samsung Easy1300 canister vacuum has lost suction (even with a new bag) and there doesn't seem to be anything blocking the hose. Any suggestions as to what to check next would be appreciated!


... Samsung Easy 1300 Lightweight Compact Canister Vacuum Cleaner

Dyson wand lost suction - Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow


... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

Hoover Model# U8185-900 Problem: No suction, not engaging Vacuum cleaner roller spins as usual, but there's no suction when trying to vacuum the carpet. Can anyone point me in the right direction? Tha


... Hoover U8185-900 Upright Vacuum

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin


... Vacuums

GE 2-Motor Canister Vacuum, 106766 Please help has anyone had this vacuum catch fire? I lost everything and my pets. I need anyone else to please let me know if you have had fire caused by this vacuum. Contact me at [email protected]


... GE 106766 Bagged Canister Vacuum

The suction that comes out of the wand is very light, it's sucking things up, but the suction is very light. You know how you put your hand on the wand of a vacuum and the suction is so strong you


Check this video out ... Dyson DC25 All Floors Bagless Upright Vacuum

I have any easy-flo built-in vacuum. I recently had the bearings on the motor, top and bottom replaced. I put the vacuum back together and it mow has low suction power. There is plenty of suction on the side of the canister where the rigid tubing meets the canister body but little suction at the wall plates. Any ideas? Roger


There is either a blockage or a pipe is open somewhere. You should check the system at the wall valve without the hose to determine if the pipes are blocked or if perhaps the hose is plugged. If one of the wall valves is damaged or open, this will af ... Vacuums

Lost suction was vacuuming and lost suction


Hi Rick,I apologize for our delayed response. I am sorry to hear you are having difficulty with your DC23. Based on the details you provided, an obstruction may have developed. For step by step instructions on how to locate and remove a blockage, ... Dyson Stowaway DC23 Bagless Canister Cyclonic Vacuum

I have a power drive baggless vacuum cleaner...it runs well, but suddenly it seems to have lost most of the suction coming through the hose and floor area. When I remove the dirt container, the suction below it seems strong. I have had it to repair twice--they have tuned it up and replaced all filters and belt. It still does not pick up well when I vacuum or use the hose. Can you help ?


There is something stopping it up,you will have to dissasemble the unit to find the blockage,this is the most likely problem. ... Hoover U6660-900 WindTunnel Bagless Upright Vacuum

I have a Eureka Power Plus vacuum, model 4702, type A. To start off, it never really had great suction. Marginal at best. Then today I was vacuuming and smelled something burning and turned off the vacuum. At that point, smoke started pouring out from the bottom of the vacuum so I layed it on it's side and the smoke cleared but I never found the source. Is it safe to turn on again after I let it cool down or is my vacuum "shot?"


... Vacuums

I have a Filter Queen Majestic canister vacuum cleaner. At the end of the wand, a button to release the attachement not only broke, but also one eyehole on the wand where one nipple on the button falls into. So therefore a new button isn't going to fix the wand because there isn't a hole on one side of the area where the button falls in place for a nipple to secure the button in place. IS THERE A REPLACEMENT PART FOR A NEW SECTION OF THE WAND WHERE THE RELEASE BUTTON IS SECURED IN PLACE THAT I C


... Filter Queen Majestic Canister Vacuum

My dyson slim vacuum doesn't have suction on the bottom. The wand has suction, how can I fix this?


... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

The suction works in the wand, but not in the main vacuum


Sounds like you have something clogged in the wand.disconnect the wand and blow through it ,if you can't then the wand is clogged ... Vacuums

No suction My vacuum does not seem to have much suction when in use. The agitator brush is rotating but I'm not able to get much off the carpet. The suction is fine when I use the attached wand.


If the belt is stretched, then it can't turn the brush rol under load, if you haven't chenged it in the last 6 months, then I would put a new one one. Also check the dirt inlet by the brush roll for a blockage. ... Riccar 8955 Upright Vacuum

My beater bar on my Kenmore 116.25615506 canister vacuum keeps turning on and off when I vacuum rugs. The suction continues, but the beater bar seems to be shorting or whatever. I checked the belts and they look like new. Any suggestions? The rest of the vacuum works fine!


... Kenmore 25512/ 25513 Progressive Canister Vacuum

After vacuuming with my Dyson animal DC 17 I placed the vacuum in a upright position and the vacuum cuts completely off. Also the wand no longer has suction....


Hi John,I'm sorry to hear you're having difficulties with your DC17. This issue sounds unusual, and we'd appreciate the opportunity to provide further assistance. Please call us free on 1-866-693-9766 - or if you'd prefer, email your details ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

We have had a Dyson DC14 for 5 years. Recently, when I run the vacuum, it whines a high pitch sound. It still maintains a suction and does not seem to have lost any power. I am unaware of anything that was done to change the condition of the vacuum. Concerned what the noise is and if it is damaging the vacuum.


... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

The wand will not stand up on its own when attached to the vacuum head. I had earlier models which did not have the adjustable height and this was not a problem--I simply turned the wand to the side. But I cannot do it on with this wand. Any solutions?


Hello. There is a small part on that wand which enables it to stand up on it's own. It sounds like yours is worn or broken. Take it to your local vacuum repair store and they will have you back up and standing in no time. The part is about ten do ... Kenmore 25512/ 25513 Progressive Canister Vacuum

No suction My Hoover Wind Tunnel vacuum runs but there is no suction. The last two or three times I used it, it shut itself off after having a burning smell. When I unplug it for the suggested 30 minutes, the motor will run again but no suction. What is wrong?? Should I just buy a nve one? This one is 8 years old.


Sounds like your motor bearings are going bad. This is generally indicated by the motor overheating, and the heat transferring out through the motor pulley, which is where the belt attaches. So, your machine is overheating, melting the belt, and then ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1064 seconds