Having problems with your Dyson Vacuums ?

No suction top or bottom - Dyson Vacuums


Answers :

Hi,

Follow the below Basic Guide :-

Step 1 A vacuum pulls air through the bag, then through the tube attachment and then through the base (with the spinning aggitator brush).
Step 2 Check for signs of suction. Remove the tube attachment from its cradle and, after turning on the vacuum, put your hand to the end of the tube. Is there any suction at all? If there is a little bit of suction then you may have a clogged air tube.
Step 3 Check the vacuum bag. It may be very full. If it is then remove the bag and replace it with a new bag. Check the suction power again. Has the suction improved?
Step 4 Check the tube attachment. Completely remove it from the vacuum. You usually have to twist and pull the tube attachment out of place at the point where it connects to the back of the vacuum. Check the suction power again. This time you place your hand on the vacuum right where the tube used to come out of the back of the vacuum. Has the suction improved?
Step 5 If the suction power has improved then you probably have a clogged tube. Dog hair, people hair, leaves and more can get lodged in the tube slowly over time and then suddenly block the tube completely.
Step 6 Clean the tube by first trying to shake the debris out of the tube. If this does not work then go outside and run a hose through the tube. Use a pressure nozzle if you have one. Run the hose through one end of the tube. Then run it through the other end. Repeat until the debris is disloged. Dry the tube and then reattach to the vacuum.
Step 7 Has suction power improved or returned to normal power? If yes then you can stop reading now. If not then read on.
Step 8 Check the air hose in the base of the vacuum. This hose is usually pretty short and you can see if there is any blockage. If you see blockage then try to remove it. You may need to reach into the hose with a tool (like a screw driver or something long).
Step 9 Has suction power improved or returned to normal power? If yes then you can stop reading now. If not then read on.
Step 10 If you made it to this step then you may have a problem with the motor on your vacuum. If this is the case then you will need to take the vacuum in to a repair shop.


If problem Persists, more likely you need to Open the Vacuum and get this Repaired. If you wish you could send the Unit for Repair or if you want to Fix it Yourself, revert and i would guide you.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!
Hi there,\012

Well first of all you can check for signs of suction. Remove the tube attachment from its cradle and, after turning on the vacuum, put your hand to the end of the tube. Is there any suction at all? If there is a little bit of suction then you may have a clogged air tube.
After then you can check the vacuum bag. It may be very full. If it is then remove the bag and replace it with a new bag. Check the suction power again. Has the suction improved? Check the tube attachment. Completely remove it from the vacuum. You usually have to twist and pull the tube attachment out of place at the point where it connects to the back of the vacuum. Check the suction power again. This time you place your hand on the vacuum right where the tube used to come out of the back of the vacuum. Has the suction improved? If the suction power has improved then you probably have a clogged tube. Dog hair, people hair, leaves and more can get lodged in the tube slowly over time and then suddenly block the tube completely.
Clean the tube by first trying to shake the debris out of the tube. If this does not work then go outside and run a hose through the tube. Use a pressure nozzle if you have one. Run the hose through one end of the tube. Then run it through the other end. Repeat until the debris is disloged. Dry the tube and then reattach to the vacuum.
If there is no suction at all after applying the above steps then you may have a problem with the motor on your vacuum. Please tell the brand and the model number of your vacuum for further help or information.......

Good Luck!!

Thanks
Repair Help & Product Troubleshooting for Dyson Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No suction top or bottom - Dyson Vacuums


Hi, Follow the below Basic Guide :-Step 1 A vacuum pulls air through the bag, then through the tube attachment and then through the base (with the spinning aggitator brush).Step 2 Check for signs of suction. Remove the t ... Dyson Vacuums

My dyson slim vacuum doesn't have suction on the bottom. The wand has suction, how can I fix this?


... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

I have any easy-flo built-in vacuum. I recently had the bearings on the motor, top and bottom replaced. I put the vacuum back together and it mow has low suction power. There is plenty of suction on the side of the canister where the rigid tubing meets the canister body but little suction at the wall plates. Any ideas? Roger


There is either a blockage or a pipe is open somewhere. You should check the system at the wall valve without the hose to determine if the pipes are blocked or if perhaps the hose is plugged. If one of the wall valves is damaged or open, this will af ... Vacuums

I just received an older model Dyson DCo7 animal vacuum. When it is turned on and you are vacuuming, should there be suction at the top of the handle while vacuuming the floor?


No it should not ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson dc40 no suction at bottom - Dyson DC14 Bagless Upright Cyclonic Vacuum


HI, it's Jim from Crucial Vacuum!\012\012When it comes to your vacuum having poor suction there are a few general maintenance procedures you can easily do to help your Dyson's overall performance. \012\012After every use, make sure to ... Dyson DC14 Bagless Upright Cyclonic Vacuum

The suction in the hose of my 2 year old Dyson Animal vacuum is compromised. I may have sucked up a small cat toy or something. Regular vac still is fine. The hose "sucks closed" after a few seconds near the top. I love my Dyson! Please help.


Hi there, it sounds as though the wand handle is blocked. To test this, remove the wand handle from the hose and test the suction at the top of the hose. If its strong here, then you will need to remove the blockage from the wand handle. If the suc ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

No suction at bottom - Dyson DC07 Bagless Upright Cyclonic Vacuum


Check for blockage in brush roll compartment,\015\012Also under the base there is a plastic transparent hose, make sure it hasn't come off, blocked or is full of holes. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The extension arm of my Dyson Animal no longer has any suction. I can attach it but it has extremely limited power to reach high places or under furniture. Also, when I stand the unit, used as vacuum, upright and the top valve opens, there is a strange noise that wasn't present when I first purchased.


You have a blockage within the wand or at the u-bend at bottom of the hose....try removing wand and see if u hav esuction at end of hose...if so wand is blocked,if not removed u-bend ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a dyson dc07 bagless vacuum cleaner. How do I split the top and bottom halves of the dust collection bin? There is a lever and catch on the side, I have tried pulling and turning, but with no success.


Hi at the top of the Cyclone there is a lever underneath the Handle. The Handle I am referring to says Dyson on it. Firstly you must release the Cyclone from the spine. After doing this you will be left with the Cyclone and the Cyclone Bin all in a ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have no suction from the bottom - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


If there are no obvious air leaks, check to see that the belt that turns the beater brush is not broken and that the beater brush has not frozen up. Remove the beater brush and clean it, spraying a bit of WD40 at each end by the hard rubber pieces t ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I was vacuuming with the Dyson DC 17 and sucked up a berber carpet string by accident and after cutting and pulling it all out of the bottom brush part, the brush no longer spins but the suction part works. What do I do?


The belt could be snapped. If this model has a brush protected belt then it has to be repaired by a service call. If however you can get to the brush roll belt by removing the bottom sole plate (turning over the vacuum so that you're looking at the b ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My dyson vacuum cleaner doesn't seem to have the same suction power it used to. I have cleaned out the canister and have taken apart the vacuum head (for cleaning carpets) and it doesn't seem to be blocked but it seems to lose suction by the time it reaches the head. The suction is strong at the end of the hose (where you attach the telescopic attachment with vacuum head) Any ideas? Thanks, Irene


... Vacuums

No suction I am getting no suction on my central vac at the vac. I do not believe that the piping is plugged up, the vacuum is not creating suction. What are the causes of no suction at the vacuum and how do I take the top half of the Nutone central vac off?


Use the guide at builtinvacuum.com/flowchrt.html to find the issue and solution. Most likely you need to test it without any filter and be sure the bottom of the unit is attached :) To get access to the motors you need to unbolt the very top sides. ... Broan-NuTone CV350 Performance Bagged Central System Vacuum

Poor Suction Heya! So I just picked up a used Dyson, but when I vacuum with it, the suction is pretty weak and it spits all kinds of stuff out the back and into my feet. When I pull the hose I have good suction, but in regular mode it hardly picks up anything. The brushes are spinning, and it eventually will clean an area if I go over it again and again. Maybe a clog somewhere? Please tell me that Dysons have better suction than my $50 Dirt Devil! Thanks!


I recently bought a second hand Dyson DC07. Its suction was poor. I removed all the un-clipable pipe bits and to remove any blockage but it all looked clear. The Final Sponge and hepper filter did have a lot of dust in it and the rotating brush was f ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!


Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

My problem is the brush on the bottom is not spinning and i think there is no suction from the bottom of the vacuum my rugs are in need of a vacuum and i 'm not sure what is going on - also nothing is going into the canister


Is there a shaft driving the brush, or is there a belt on this one? Are they intact and working properly? It could be possible that the motor isn't moving which would cause no suction or brush movement. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

No suction on my Dyson canister vacuum. - Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum


Hey,I see this problem is more frequent..I'm guessing your dyson 'sounds' blocked.See my solution:http://www.fixya.com/support/t4547920-loss_suctionThis fixed mine right up.It was not working well at ALL, so i open ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Dyson vacuum suction loss - Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum


Clean it outcheck all the filtersI think it has a foam filter as well as the filterless designclean and lubricate the motormake sure it is not leaking and sucking in air from somewhere else ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

My dyson DC07 animal does not have the suction it once had I saw a dyson program that showed a filter in the top of the canister I was just aware of the filter around the wheel. Is there one on top of the canister and how do you get to it


Hi\012\012The DC04 Dyson has a filter at the top, but the DC07 has one at the side on the bottom and one underneath the cylender.\012\012Take all the parts off your dyson and throw them in the washing machine and then put them ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My upright kenmore progressive vacuum will not suction up when using the sweeper. It will suction things when I use one of the tools. I have put in a new bag and have tried to see if anything is blocking the bottom. It sometimes makes a very loud noise when I try to vacuum. If I press the intell clean on and off yellow button the noise may go away but it still does not work.


Double check hose placement, making sure you have the hose inserted into the correct slot. The long attachment nozzle stores in the front hole on the right, and the sucking hose inserts into the rear hole on the right. I know this is too simple of a ... Vacuums

I have the Miele S7280...the one without the clog hatch on the back. I took the bag cover off, then continued the remove the screws and cover underneath it to detatch the top from the bottom. Found the clog and cleaned it out. Heres the problem...now the power nozzle light comes on and the vacuum "on" is lite up red, but it will not come on. Checked the filters and the bag. It certaintly seems like the top and bottom are meeting up to latch into each other, but I have no power. Help!!


... Miele S7210 Bagged Upright Vacuum

I have a Eureka Power Plus vacuum, model 4702, type A. To start off, it never really had great suction. Marginal at best. Then today I was vacuuming and smelled something burning and turned off the vacuum. At that point, smoke started pouring out from the bottom of the vacuum so I layed it on it's side and the smoke cleared but I never found the source. Is it safe to turn on again after I let it cool down or is my vacuum "shot?"


... Vacuums

I have the top of the line kenmore canister vacuum. According to the bottom plate the model nimbler is 116.28015700 I was doing the normal vacuuming and the bag full light came on and the vacuum action stropped. There is still power to the mortorized handle and agitator attachment. Is there some type of circuit breaker reset button for the vacuum function? This unit is probably less that two years old and has had very little use


... Kenmore Vacuums

I have a Dyson DC24/ all floors, serial number 530-US-D78353 that I have registered already w/ your company. The vacuum is generating suction from the main outlet (that goes to the canister)///but once I place the canister into position..there is no suction from the floor foot. The roller is working/spinning, but no suction..picks up nothing, I have cleaned and rechecked all filters and can not figure out why I suddenly have no suction. Appreciate your input and/or advise where there is a local


... Dyson Ball DC24 Bagless Upright Vacuum

Ive got powerful suction from my wand when i am using my dyson upright, so the suction on the bottom not good


... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1195 seconds