Having problems with your Dyson Vacuums ?

The beater bar is not rotating - Dyson Vacuums


Answers :

Hello,

To get the bar to rotate once again, you have to troubleshoot the the vacuum cleaner.

To troubleshoot it, follow the steps below:
\015\012
    \015\012
  1. Suspect a tripped breaker, broken on/off switch, or a damaged cord if the motor won't run.
  2. \015\012
  3. Insure that you aren't running too many appliances on the circuit if\015\012the breaker continues tripping. If that's not the problem, you may have\015\012a short circuit in the power cord. Replace it immediately to avoid fire\015\012hazards.
  4. \015\012
  5. Check to make sure the bag isn't full if you aren't getting much suction. Replace the bag if it's full.
  6. \015\012
  7. Make sure the hose is properly connected to the machine and that there are no obstructions in the hose or fan.
  8. \015\012
  9. Repair a cracked hose with duct tape. Prevent creased hoses by hanging them over two pegs on a closet wall.
  10. \015\012
  11. Remove hair and strings that tend to get wrapped around the vacuum brush with a pair of small scissors.
Take care
Repair Help & Product Troubleshooting for Dyson Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Beater bar on my dyson is not rotating - Dyson Ball DC24 Bagless Upright Vacuum


Hi there,Your DC24 is equipped with a sensor which shuts off the brushbar if something jams it. Once you've checked the cleaner head for any obstructions, and removed any threads or hair from around the brushbar, you should be able to reset t ... Dyson Ball DC24 Bagless Upright Vacuum

I have a Dyson 15 "the ball". The beater bar will only rotate if the vacuum is engaged and the handle at a high angle. The bar stops when I drop the handle to a lower position. The condition is repeatable. Can you provide part and repair instructions?


If air is leaking in somewhere, you will not have any suction.\015\012\015\012\015\012Also there are some possibilities that has to be checked to confirm the fault.The problem is minor but the possibilities are too much for this pa ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

The beater bar is not rotating. - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


You need to replace the belt that drives the beater bar ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I HAVE A DYSON DC07 I HAVE CHECKED ALL HOSES AND PLASTIC ATTACHMENT SECTIONS , CANNOT FIND ANY BLOCKAGE ANYWHERE IN THE SYSTEM .THE BELT IS GOOD AND THE BEATER BAR IS ROTATING WELL , BUT THIS VACUUM WILL NOT PICK UP ANY THING. I DID NOTICE THAT THE HEPA LIFETIME FILTER IS BLACK AND NOT SURE IF IT CAN BE WASHED OR CLEANED. THANKS BOB!


I have just cleaned mine just a half an hour ago - SAME PROBLEM !!\015\012ok take the dust cylinder off the vacuum cleaner and take the plastic clear cylinder off - there is a clear clip one side and you might need a small knife to unclip other ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The beater bar is not rotating - Dyson Vacuums


Hello,To get the bar to rotate once again, you have to troubleshoot the the vacuum cleaner.To troubleshoot it, follow the steps below:\015\012\015\012Suspect a tripped breaker, broken on/off switch, ... Dyson Vacuums

The beater bar will not rotate - Dyson DC07 Bagless Upright Cyclonic Vacuum


... Dyson DC07 Bagless Upright Cyclonic Vacuum

While vacuuming my carpet, a corner of a throw blanket was sucked into the beater bar. I turned the vacuum off and was able to pull the corner of the throw blanket out without much resistence. I plugged the vacuum in and started it and now the beater bar isn't rotating.


Try pressing the reset button on the nozzle, probably just tripped out the brushroll motor ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I have a dyson DC28 vacuum and the power button flashes on and off and the beater bar quit turning. I turned it over and found some string caught on the beater bar which I removed, but the beater bar still does'nt turn and the power button still flashes on and off. I hope you can give me a solution to this problem.


I had the same symptom with my wife's DC28. The problem was associated with the cam driven height adjustment mechanism. The beater bar must rock freely up and down when pressing on the tabs that the end cam lobes actuate. On ours I found hair and cru ... Dyson DC28 Animal Bagless Upright Vacuum

My dyson animal is hard to push on carpet - the beater bar is still operational. When I turn off the beater bar and run the vacuum on hardwood the beater bar stops moving, but it still ''rolls'' on the hardwood - it doesn't pull up like it used to. It also seems to not be picking up as well as it used to, although no blockages are present and the filter is clean.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The beater bar on my Dyson won't turn. The vacuum runs and suctions but the bar won't turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won't turn


The belt doesn't have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won't operate the way it is supposed to. You can get replacement Dyson Belts here: ... Vacuums

I have a dyson dc14. the brush bar will not rotate when the vacuum is running. the belt is attached and it will rotate by hand. when you switch from bare floors to carpet-the bar will not kick in and rotate.


\015\012Hi,\015\012Check that when you pull back handle to vacuum the clutch control knob which is located front lower left side of machine moves to drive position & is not stuck in off or park po ... Dyson Vacuums

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I was cleaning the hair from the beater bar, and it popped out with the belt still attached...have tired to put it back in , but the beater bar will not rotate when the vacuum is turned on


When you put it back make sure that the ends of the bar fits exactly in the ends o the box and has to roll smoothly even when you rotate it with your hand when you try this has to be disconnected ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Removing cover over beater bar for cleaning on dyson animal vacuum. Accidentally ran over mess on carpet and need to clean inside of cover and beater bar. Thanks


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Kenmore 39522 vacuum beater bar keeps rotating after unit is shut off. Even unplugged it to move to another room and when I plugged it back in, the bar rotated a few more times! Has a definite clicking sound when this happens. Purchased in January 2008.


The berings or something inside might be going bad. ... Vacuums

My son dropped the vacuum down the stairs and now the vacuum works but the front part of the vacuum does not drop back down when vacuuming any type of floor. It slowly drops and does not stay on the carpet. hope this makes sense. I have cleaned filters and suction seems strong at the small hose. the beater bar rotate very fast still.


May be part missing. this is unit has 5-year warranty.you can send to service. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Terrible noise My dyson was working great then started making this horrible noise. I cleaned the bar but noise is still there. I discovered the beater bar went around three passes then froze and started horrible noise again. my husband got the bar turning but after 2 swipes vacuuming it did it again. Can it be fixed or is it time to retire it and buy a new one. Wendy Kiser


That noise is the clutch. A very expensive part and very hard to replace. When a problem with the clutch happens it's generally not worth the time and money to replace.I suggest getting a different type of vacuum, maybe a Miele or Sebo. W ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a dyson animal (purple) "the ball" vacuum and now when I push the button to turn off the beater bar it turns off my vacuum. Help?


There is a linkage between the on/off and the beater bar switch that probably has came loose or is broken. It also could be wires shorting out. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

How to remove the beater bar on a dyson ball - Dyson Ball DC24 Bagless Upright Vacuum


Hi there,To remove, clean and replace your DC24's brush bar, please follow the steps shown in the video below. I hope this helps - if you need any further assistance or advice, please visit ... Dyson Ball DC24 Bagless Upright Vacuum

The rotating bar is not rotating. HELP! - Dyson DC25 All Floors Bagless Upright Vacuum


One of the buttons turns on the machine and the other turns off the rotating brush, since the Dyson does not work well at all on bare floors with the rotating bar running. The buttons on mine are right on the front of the machine and are very large. ... Dyson DC25 All Floors Bagless Upright Vacuum

Dyson vacum beater bar does not work - Dyson DC14 Bagless Upright Cyclonic Vacuum


DC14 have two drive ... Dyson DC14 Bagless Upright Cyclonic Vacuum

Dyson beater bar won't spin - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


Hi its Darran at Dyson. \012he first check is to ensure that the brush control dial is set to the correct centre position when the machnie is locked upright. When you release the head the dial should move forward to the on position and th ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson blueprint beater bar won't turn - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


The Dyson DC 17 has a rug / floor switch on the head of the vacuum. Please check to make sure the switch is in the Rug position. If the brush roller still does not turn then you have broken the belt and need the following part.\015\012 ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

How do i adjust beater bar of dyson dc24 - Dyson Ball DC24 Bagless Upright Vacuum


... Dyson Ball DC24 Bagless Upright Vacuum

DYSON 28 ANIMAL BEATER BAR NOT SPINNING - Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum


Hi there,I'm sorry to hear you're having difficulties with your DC28. The machine is equipped with a sensor which shuts off the brushbar if something jams it. Once you've checked the cleaner head for obstructions, and removed any threads or h ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0830 seconds