Having problems with your Dyson Vacuums ?

Turbine Head Brush Tool - Noisy

\015 I have purchased my Dyson 2 Years ago and I use the brush tool on one carpet that I have in the house which is 1.5mX2m once every two weeks.\012One month ago, the tool started making an awful screeching sound as if the bearing has worn out. I took the brush to the Dyson representative here in Israel and I was told it is not under the 5 year warranty, they can not fix it and I need to purchase a new brush for over 100$.\012\012Is there a way I can fix the brush on my own?\012\012Thank you!\015

Answers :

See if there is something wrapped around the brush area itself which could cause the noise
Repair Help & Product Troubleshooting for Dyson Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Turbine Head Brush Tool - Noisy


See if there is something wrapped around the brush area itself which could cause the noise ... Dyson Vacuums

Suction on my dc08 is very poor when turbine head is attached - no problem when not. I have cleaned the brushes an ensured there are no blockages. Why the loss of suction when using turbine head ?


Please go to the web page www.dyson.com and go next http://www.dyson.com/support/help.asp?article=1468&product=DC22-TURBINEHEAD-USand fix it. with commong sense.God bless you ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

My dyson dc32 turbine head is not rotating even i have pulled the red round thing and it is noisy help


... Vacuums

MY DYSON MINI TURBINE HEAD BRUSH WON'T TURN, EVEN THOUGH THERE IS NO BLOCKAGE


... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Turbine head brush bar not turning - Dyson DC23ACTUSC Bagless Canister Cyclonic Vacuum


... Dyson DC23ACTUSC Bagless Canister Cyclonic Vacuum

Dc11 dyson the brush head turns very slowly but when i take brush head cover of (the yellow part) and put my hand over the suction inlet part the brush head turns really fast. Have cleaned out collection chambers eg the hoover bag have washed the sponge with the little pictures of taps on it what now . thanks alan


I have taken the brush heads off and pulled all the hair out of the small gap between the chrome shaft and the plastic gear housing. Then a small amount of 3-in-1 oil into that gap to lube the internals and just a little through the air intake on th ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

I caught a hidden shoe lace in my dyson 17 beater head....shut it of quickly....removed the lacing from around the head....loosened the three screws on the botton of the head....cleaned it out from whatever little dust there was....checked the heads belt reset the roller brush into the head...but alas no beater brush action. what to do?(I've had my dyson about5 months....HELP!. thanks, Jan Selman


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Is it possible to disassemble a Dyson floor tool/head please? (Not the turbine head!-the duel floor head!)


Take the head off then take to the nearest garage and use there vac to **** it out or the blow it out with there compressor. ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

DC20 Turbine Head rubber part torn


The only place you might get the part is from DysonThet do not let these type of parts to any trade ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Miele, Flamenco II. 2 probs. 1. the head brush is not turning when I put it on the floor. If I pick it up to look inside...the brush is spinning fast..I put it down on the floor...the head does not spin at all. 2. The suction power has dropped significantly. The suction used to be so intense, the head would **** itself to my floor and hold on...now, hardly any suction at all.


Sounds like the belt is not on correctly on the beater brush or the belt is worned out now for the suction check filters or bags that need to be empty or clean ... Miele Vacuums

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a


Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums

Clarke Instructions helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? t


... Vacuums

Clarke scrubbers helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? ther


... Clarke Vacuums

I am trying to get to the on/off switch on a Panasonic MC-E851 . One of the two screws has a very unusual head and I Cannot find a tool to fit . What is the head type of the screw called to allow me to buy a tool to foit?


... Vacuums

Brush head not rotating. Press rotating button and head does a little jump but no more. No build up of debris on head.


... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I have a Hoover spin vac # 7410-900 the brushes don't spin but i can hear the pump running , checked the brush block stem thats fine the unit feeds water and soap. but i have no vacuu.me or brush movement getting ready to rip the turbine out to check it . the weird thing is it worked fine and then just stopped


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

We have a kenmore canister vacuum and it runs but when turn on the rug clener brush the brush will not run we then put on small brush head and that will work


If the power head motor runs, but the brush doesn't turn, then the belt is broken. Replace the belt and it should work. ... Kenmore Vacuums

Brand new Hoover Max Extract Deep Cleaner brushes won't turn. Read manual. Checked filters - all clear. Set Spin Scrub Mode Selector to a scrub setting. Brushes still won,t turn. However the brushes on the Spin Scrub hand tool rotate.


... Vacuums

Not exactly a blow gun. Convertible blower/vac - Sears Craftsman. Wire broke off ONE brush in the motor. Paid about $90 for the vac - Sears lists the WHOLE motor as one part - $88. Have requested brushes (they are provided with a lot of my 'cheap' Harbor Freight tools) but no go. Just get the canned reply - buy the whole motor. Actually got it working again... CAREFULLY drilled and tapped a 4-40 screw into the brush and soldered the lead to that... Always a way, isn't there?


... Vacuums

Hoover steamvac turbine and brush control switch


Try checking your drive belt might have come of or just loose ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The ball bearings are stripped from the roller brush of the power head for my electrolux model N115M


You will most likely have to replace the roller brush wth bearings. i just recently had to replace my wifes on her electrolux. i was able to order the parts online at sears parts direct, but there are many places to get them online. you will need the ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Melted bristles in brush head


... Hoover U5458-900 WindTunnel Bagged Upright Vacuum

Turbine head Dyson DC39 The turbine does no stay on consistently


... Dyson DC39 Animal canister vacuum cleaner

Cleaning The Brush Head


I got pretty good results this way (and mine was trashed): Hot water first. Dry the exterior enough to tape the suction end with duct or electrical tape to get a good seal. fill from the other end with bleach. Shake it around and then let it sit in t ... Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0428 seconds