Having problems with your Dyson Vacuums ?
No suction for floor but suction works when using the hose
\015 Upright lightweight\015
Repair Help & Product Troubleshooting for Dyson Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
My dyson dc17 animal will pick up via the hose attachment but there is no suction when you use the regular vaccuum on the floor - you can hear the difference in the suction once you put the floor part down - we took it apart - cleaned it - checked all hoses - still does not work????
Hi its Darran at Dyson.Check that the brush control dial is in the centre position when upright and then moves forward when the head is released. If the brush bar is still not spinning when switched on in the vacuuming position, check th ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Dyson all floor vaccum no suction when hand held wand is turned on... doubled checked for cracks in hose -- none took house off unit to check for blockage --- none.. suction works fine when using as normal on floors.
You need to replace the belt that drives the brush on the underneath side of the vacuum. To do this, you need to flip the vacuum over and remove cover plate. There you will find the broken, or stretched out belt. Remove the brush and place the new be ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
We have two of these vacuums and both of them have experienced the same problems. First the floor heighth adjustment doesn't work and now neither one will pick up on either carpet or floor when in the brush/floor mode. They both seem to work with the suction hose function. We have removed the back panel to see if there was an obstruction but it was clear. We have changed the bag and the small filter (not the HEPA filter) all to no avail. What else can we do? We are desperate to use our vacu
Did you check the powerhead for obstructions? With a bend in the tube just below where the hose connects, this is a common spot for clogs. To check, detach hose and drop a coin in the hole. If it doesn't drop through, a blockage is present. Use t ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum
Recently purchase SC-N500 vacuum cleaner. Worked well only the first 2 times I used it to clean up plaster dust from floor after sanding. Since then it has not worked at all well wiht very poor suction. Fluff gets stuck in the hose and has to be manually removed. Suction power is very poor. I have washed the filter to remove the dust with no difference. Who do I contact in Brisbane to service or assess the problem further.
... Sanyo Vacuums
I have Bissell ProHeat 2X 9300-M that I tried to use again today. Is does not dispense solution when turned to Floor Cleaning, when switched to Hose it seems to be working fine. Brushes and suction are working as well. Soap and water containers are full. I took off and replaced tanks, waited to prime the pump multiple times without success. Not sure what is going on.
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
No suction for floor but suction works when using the hose
... Dyson Vacuums
The suction is good, but it can't pick up most of the stuff on the floor. The hand held hose works very well, but it doesn't even pick up little fuzzies reliably when I push it along. And, the suction is too hard I think because it used to push easily and now I have to push really hard, even on flat carpet.
Check entire length of hose, including the piece in the power head, for clogs. Simply drop a marble in one end and allow it to roll out the other. If it doesn't, then the hose is clogged somewhere. ... Dyson DCO7 Animal Bagless Upright Cyclonic Vacuum
Hoover Jet and Wash 1500w S6254 001. Used once with great difficulty as assembly and use instructions are hard to follow.Now will not work as carpet shampooer at all, although assembly is correct as far as I can see and both motor and pump appear to be working and I am using the recommended cleaning fluid.Hoover website is no use at all in solving the problem.No cleaning fluid is being drawn up from the tank in to the cleaning fluid hose.There is suction from the suction hose so the problem appe
I am having the same prob my uncle got me one i cant find the manual anywhere to set it up the prob i have is where does the handle to make the water go out connect tooo ??? on the main pipe that sucks it back up i have tried every which way but not ... Vacuums
My Bissell BS3920F upright (similar to the 10N6F) has been working wonderfully for the past 3 years but suddenly seems to not pick up dog hair as well as it used to. It has been pulled apart by my husband to ensure nothing is blocking the hoses etc and when running the suction seems to be there. It seems to grab the dog hair and leave it in a straight line directly under the unit without picking it up. I then disconnect the hose and use to hose to pick up the dog hair. This works well but obviou
Check to see if your brush is not worn down, they do wear with age - compare the length of the bristles with a new one. Replace the brush ir there is a significant difference in bristle lengths. Also check the flexible ben ... Bissell Vacuums
Suction hose I can't get the suction hose to work...and I have cleaned it out to make sure it isn't plugged. There is a small amount of suction just not enought to pick anything up.....the floor part works great...what could be the problem
I would first double check the hose, remove it and drop a marble through it to be sure. make sure the bag is new and also check the filter underneath the bag if it is clogged it could cut the suction. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
My dyson seems to have lost its suction therefore is not picking up anything yet i have found that when my dyson is standing upright it has a little more suction but nothing like how it use to work. This has only happend in the last 2 weeks. I sanded a floor & though the sander picked up majority of the dust i did use the dyson to pick up the excess and it is since then that my dyson has not been working to its full potential.
Hi there,\015\012\015\012Sorry to hear you're having a problem with your DC07. You should be able to resolve the issue by following these simple steps: ... Dyson DC07 Bagless Upright Cyclonic Vacuum
My new Kenmoore Powermate 116 canister has poor suction. I have no pets and light dust. Its not picking up small particles on the wood floor with the floor attachment. When I put my hand to the suction it feels weak. Cleared hose and changed bag. Using again, same issues. This should not be happening with a new vacuum. Is it a bad design in the elbow joint of the hose? I want to return this!!!!
First of all disassemble the handle and hose as much as possible and examine the inside. Make sure there is not any significant debris lodged in the hose somewhere like a plastic bag or something.\015\012\015\012Also check at the top of t ... Kenmore 23912 Progressive PowerMate Bagged Canister Vacuum
On my DC17, the wand is not working right. The upright part works fine, but when I go to use the wand, the hose sucks in on itself. I get suction for a few seconds, then the hose collapses in on itself and no more suction.
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Floor attachment does not suction, no clog in the hose, hand held works when dettached from floor attachment
Have you checked the floor head? Use a pipe cleaner or twisted metal to carefully and gently see what's in there. It sounds like dirt or something has definately sealed up the main suction channel. ... Vacuums
My eureka optima upright bagless vaccum has VERY low suction using the floor part. the hose has excellent suction. i removed the little translucent door underneath and there were no blockages, i cleaned the brushroll thoroughly and that hasnt helped either. i know this probably isnt recommended but i turned it on to the floor setting with the brushroll off and stuck my fingers up the intake as far as i could, the suction was good further up but it just seems to stop down at the base. because i s
I will try and help here. Is the sole plate on the bottom of the vacuum complety on and there are no visible cracks along the seam where it meets the body? This is the usual cause for this. Onc you take of the plate to access the roller and brushes, ... Eureka 431A Optima Bagless Upright Vacuum
I have a power drive baggless vacuum cleaner...it runs well, but suddenly it seems to have lost most of the suction coming through the hose and floor area. When I remove the dirt container, the suction below it seems strong. I have had it to repair twice--they have tuned it up and replaced all filters and belt. It still does not pick up well when I vacuum or use the hose. Can you help ?
There is something stopping it up,you will have to dissasemble the unit to find the blockage,this is the most likely problem. ... Hoover U6660-900 WindTunnel Bagless Upright Vacuum
No suction i have a bissell lift off revolution vacuum. I have cleaned all the filters and emptied out the canister made sure that the hoses are not plugged but it will not pick up unless you use the hose. the floor brush is clean and still no suction coming from under the vacuum... could you help me please
Is there a blockage in the small hose in the bottom of the machine \015\012take of the pod and you will see the small hose, \015\012Is the main hose pushed into the bottom housing ... Bissell 37603 Upright Vacuum
I cleaned out the hose and removed brush to clean and checked belt. Everything seems to work but will not pick up or suction on carpet. The hose is totally clear from clogs. I can see the floor from one end to the other. What am I missing that might be causing lack of suction?
Hi troupdavid,I see that your Vacuum is having issues with it suction, you mentioned that you took it a part to clean it, see steps below.\015\012\015\012Check if everything is inserted prope ... Hoover Tempo Widepath Upright Vacuum - Blue
Dyson hose suction strong...when using the brush bar no suction available. Have looked to see that all airways (u-bend) are clear. When engaging the brushbar the brushbar turns but no suction to floor.
Hello,There\012 are several things that this could be. Probably the most common problem\012 that we see when customers come in with this problem is actually a \012fairly simple problem to fix. Here are just a few things that this could\01 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
After using switch to go from floor to carpet, noticed the roller brush not working, and therefore the self-propelled feature also not working. Replaced what I thought was the problem, a loose belt, but still does not work. Motor runs and there is suction...???
... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum
Poor suction absolutely loved the machine when I first got it. I have dogs so it is getting a work out. however, the suction isn't as great as when I first got it. I have cleaned the washable filter and empty the cylinder after every vacuum. When I use the hose, the suction just isn't there. anything else I can do?
OK- I had the same problem and I took it to sears for service, It still wasn't great. So I proceeded to pull out all of the filters, including the internal filter that is not easy to get get to. I washed it and air dried it, put it all back together ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
My Hoover vacuum is not vacuuming the carpets or floors. When I release the tube to use the smaller end the suction works perfect. So i believe the problem is in the rods on the floor or in the part that vacuums the floor! Can you tell me how to fix it , or where can I take it to get it fixed? thanks
Ive just had the exact same problem. In the very back lower portion of the vacuum You will need to take it apart. I guarantee there is a clog. You might also check your belts to make sure they are still on track. ... Hoover Vacuums
The suction still works but the primary floor vacuum doesn't. I checked the belt and its not broken. The engine that runs the floor vacuum doesn't engage like it used to
The belt doesn't have to be broken to affect the the way the vacuum picks up on carpet. If the belt is stretched then it will slip and not turn the roller brush properly. Here is the manual and belts you need: ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I have a dyson 07. Vacuum works fine, great suction using the hose. How do I switch to using the carpet vacuum. (I lost my instruction book) Thanks
If this unit has a suction hose built in to the handle, the carpet vacuum should start working after you return the handle hose to the proper position. ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Hello, my Kenmore 27514 canister vacuum only works on the hard floor...the carpet suction stopped working while I was using it. Is there anything I can do to fix it or is it necessary to take it in for repair? The vacuum is only 1.5 years old. Thanks. Susan 702.340.8015
You need to replace the belt that drives the beater bar. You can do this yourself very easily. If you need help, let me knowJim ... Kenmore 27514 Bagged Canister Vacuum