Having problems with your Dyson Vacuums ?
We have a dyson vaccume and what ever makes it stand isnt working. I dont think we did anything wrong. But I cant make it stand.
\015 T\012The red stand isnt working and I cant get it to stand upright.\015
The steel rod has come out of the groove that makes it go up/bown this video will show you.
Repair Help & Product Troubleshooting for Dyson Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
We have a dyson vaccume and what ever makes it stand isnt working. I dont think we did anything wrong. But I cant make it stand.
The steel rod has come out of the groove that makes it go up/bown this video will show you. ... Dyson Vacuums
My steam vac was working...i thought the dirty water was full but it didn't make the hi pitched noise now that i think about it.....now it is not sucking up the dirty water.....i checked to make sure it was placed right and can't visually find anything wrong....help! i have pet stains to vacuum up...this is only about 1 year old.....
\015\012The most common reason for lack of pick up is that the lid is not fully seated on the dirty water tank. Be sure to hook the two tabs on the front of the lid, and then snap the rear latch into place. Another reason is that the duct on th ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Hi i have a dyson dc07 it doesn't work in the upright mode. It works with the tools only .... think the brush isn't turning. it's not making any nasty noises just not picking anything up!
Has the belt snapped? ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Roller got power cord. This stretched out the belt. I replaced the belt, now the vacuum is making a noise. Cant find anything wrong, what could be making this noise?
Most rollers have several different positions you can install the brush in check and make sure the roller height is equal. ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum
My dyson makes a noise every few seconds that sounds like a very loud 'squeal', or a giant budgie chirping! It's still picking up ok. I've taken it to bits and cleaned it, but I cant find anything wrong. Help.
Hi thereNot sure what is causing this, it could be that the belt that drives the clutch and brush bar is wearing so is slipping (like a fan belt on a car). If this is the case, we could arrange for this to be repaired. Call ou ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.
Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum
Motor still runs--sounds like jet engine. do I need a new motor? or is there some sort of muffler that has malfunctioned? vacuum belongs to disabled mom---so trying to do work ourselves--cant afford much. dont see anything obviously wrong--but know nothing about electric motors.
This little vac I think is actually made by Samsung. If it is ROARING and vibrating, either the bearings or suction fan is in bad shape. Remove the lid as if to inspect the belt and see if there is a visible intake opening with a plastic fan rotatin ... Bissell 3590 CleanView Bagless Upright Vacuum
My sister dropped her roomba than brought it to me complaining it does'nt work anymore. I took it apart, cleaned everything i knew to clean,could not find anything obviously wrong so I put it back together.I charged the battery than tried it. The green light comes on when you push the clean button and it makes a little grunt noise but that's it.
Have a look at the motor brushes if there broken or poped out this is were the "grunt is coming from" the motor is trying to turn but cant? ... iRobot Roomba 4000 Bagless Robotic Vacuum
My filter queen majestic quit working. I opened up the unit to see what was wrong and I did not immediately notice anything wrong. Upon furter examination I noticed one of the traces on the printed circuit card was burnt. I used a soldering iron to "bridge the trace and it appeared to fix the problem for a while. Now it has stopped working again, and when I jumper the trace to run the motor it seems to work. Should I just replace the card? Or is there a more serious problem with too much current
I recommend replacing the card. Soldering involves the risk of further damaging the card, so it would be useless anyway. Why waste valuable time?\015\012There is a possibility of the motor overheating, generally due to a blockage in the airfl ... Filter Queen Majestic Canister Vacuum
Oreck XL21 just will not work at all any more. Beater is clean - belt is fine. Fresh bag - inflates. Took the thing apart - checked for blockages at intake, bag entry, and the tube. It just doesn't vacuum anything. No suction at all for anything stronger than air. I'd say it doesn't ****, but that would be ironic. Are these known for just "quitting" after a while? We take it in for maintenance as recommended to replace filters, etc. Is there some miracle trick to make it work or sho
Did you make sure the brush turns freely? Even though it is clean, if it does not turn freely with the belt, it will not beat the carpet and pull debris up into the unit.\015\012\015\012Another (drastic?) thing to try would be to take the unit ... Vacuums
On the bottom of the Fantom Fury where it states:"The United States and Canada utility patent....". Now go to the far right end of this statement (the end opposite the spring, well I have a crack in the plastic which, when toggled, moves the entire plastic underside of the vacuum to move. In other words, I think I need an entire bottom plastic plate. The cracked area also makes the foot lever (which lowers or locks the vacuum handle) not work as the crack makes it impossible to work. I know
Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=545424\015\012Generic problem for all Vacuums\015\012On the bottom of the\015\012Posted by c ... Vacuums
Hello i own the bissle proheat steamer it turns on but no water or soap or suction from floor or the utensiles ive taken the take off the back to scope out anything that could be in the way but dont see anything the motor is making that clogged vacume noise witch makes me believe something could be stuck somewhere in it but it could also be no water is getting to the pump or despencer but the brissels still work belt for that is good where would i be best to check and where is the location of th
... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.
... Windsor VS14 Versamatic Bagged Upright Vacuum
I have only had my shark steam mop for about a month and only used it twice. I tried to use it yesterday and it would not work. The green light came on and it worked for maybe ten seconds, then it completely shut off. I tried switching outlets and draining the water but nothing worked. It still doesn't work today either. What do you think is wrong? Does this product have a warranty?
Yes has warranty call Shark/europro. ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work
It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum
I cant detect where the damage but it dosn't work or even the light indicator didn't open, no heat even in maximum level, i plug in for almost an hour but the iron is not responding or not really working and still cold.... how can we fix to make this appliances work again? tanx,
If it's an old iron, then maybe there is some loose wire inside, which could be fixed with proper tools and some knowledge of electricity, but if you are not familiar with taking apart electric appliances - you should just replace it, because it is p ... Vacuums
I bought one of these units last year and it worked great for about 9 months and then it stopped brewing coffee. Not sure what is wrong. It will not heat the water to make the coffee. Any idea as to what could be wrong?? Thank you. Pierre
Hi,Either the heating element is completely corroded with mineral from the water or the heating element has gone bad...If it is not heating at all there is some kind of electrical problem or the element is gone bad... ... Vacuums
I have had my RCA microwave model # RMW1108 for about 8 months now. It was working fine until yesturday evening. I went to warm up some food for 2 minutes, the microwave itself was on and everything appeared to be working except my food did not get warmed up. I plugged it out and checked all over it for any damage but i could not find anything wrong. What would cause it to just stop heating up the food? Is this type of problem covered in the 1 year manufacturer's warranty.
The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?
As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Vaccum is making a loud high pitched sound, doesn't work well through the hose or the floor piece and shuts its self off after about 5 minutes. I have cleaned the entire vacuum out several times but this problem persists. Usually after I clean it, it'll work for a couple months, not this time. Vacuum is only 2 years old, is this typical?
... Dirt Devil Featherlight Bagless Upright Vacuum
Loose wire ive got a loose wire inside my vax cyclonic 1700w and ive stripped it down but cant see anything and its still not working but it was working when i moved the wire from side to side. Please help
Sounds to me like you have a open wire. There is a break in the wire inside to the insulation and as you move it, it gains and loses connection. You can test it with a continuity tester as you move the wire or just replace it to see if that solves th ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
I bought a used vacuum seal machine (hobart model ht-120) it does excellent vacuum but it doesnt seal correctly all the time. it seems like there is something wrong with the valve that activates the bar that goes up and makes pressure and heats the bag for complete sealing. The heating is perfect but what is not working is what make the bar go up and down.
Model#F5858-910 hoover steam vac,silver ,spin and scrub. It doesnt seem to spray cleaner it seems to stream it now. what could be wrong? I cant get to end of where it sprays to see if something is blocking it . otherwise it works great. I have it about 8 yrs. always worked good until recently
... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
Have a kenmore cannister vaccum, brush is working but it is not picking up anything the suction is not working ?
Remove the hose and clear any obstruction from inside of it. If that does not work check the bag and filter if one is installed ... Vacuums
I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...
The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum