Having problems with your Electrolux Central Vacuum ?

Motor shaft wont turn on EL2050 - Electrolux Central Vacuum

Answers :

Have you tried running the brush motor without a belt on it? Does it not spin without the belt? If so, you may have worn motor brushes (not too expensive parts, but make sure you order both brushes, or make sure they are sold as a set). If your motor is in good condition (you can check the brush motor by hooking it up to a momentary power source NEVER apply constant power to a motor that is not mounted to either the machine or something to keep it from running away) There is sometimes a switch down towards the brush head assembly that could be bad.
Repair Help & Product Troubleshooting for Electrolux Central Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Motor shaft wont turn on EL2050 - Electrolux Central Vacuum

Have you tried running the brush motor without a belt on it? Does it not spin without the belt? If so, you may have worn motor brushes (not too expensive parts, but make sure you order both brushes, or make sure they are sold as a set). If your motor ... Electrolux Central Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

No suction on my Electrolux central vacuum in all outlets even though motor is running and there is no clog in the hose.

I would start with washing out the ilter really good and letting dry. then try the system. ... Electrolux Central Vacuum

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely

The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula

There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

I have looked online for this vacuum but could not find it. The closest one is the Eureka 8803 but the p/n on mine says 79307. I have totally disassemble this vacuum. There are no clogs anywhere. Motor spins by turning shaft. Belt is new and turns brush. It still has absolutely no suction.

... Eureka Boss Capture 8803AVZ Bagless Upright Vacuum

Kenmore central vacuum wont turn off at handle,

... Vacuums

The belt on my used Eureka Boss 5857 upright slips off the end of the motor shaft every time the vacuum is used. When I turn the brush roll slowly by hand, the belt walks toward the end of the shaft. It looks like there was a plastic projection from the base that snapped off, and maybe that plastic piece used to block the belt from falling off. Do I need to try to reconstruct that plastic piece, or is something else wrong?

... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?

... Vacuums

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan

Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum

My central vac unit does not turn off even when hose is disconnected. I have to unplug the motor unit in the garage to shut it off. What do you think the problem is? It is a 7 year old Electrolux

Possibly the power module. Or a short in the wiring. Take it to the local Aerus Electrolux store and have it checked by a service tech to be sure. The pm is a lot less expensive to replace than a whole cv. ... Electrolux Central Vacuum

Vac motor runs but belt wont turn - Eureka Power Plus 4703D Bagless Upright Vacuum

Its time to check and/or change your belt. to do this you want to remove the two screws on the top casing and remove the cover. There are detailed belt change instructions on a sticker under the top casing on how to remove the brush and b ... Eureka Power Plus 4703D Bagless Upright Vacuum

Hi I have the electrolux vacuum 6500 SR bought in the early 90's ish... It is making a very load sound when i turn it on like a grawl or grinding sound. What could this be? Motor Belt or other???

Based on what you have said it sounds like the bearings in the electric motor are finished, probably just as cheap to buy another vac, sorry. ... Electrolux Epic 6500 Vacuum

My Electrolux Upright vacuum cleaner will not suction. Motor will run to turn roller, though.

The air passage form the brush area to the bag is plugged somewhere. Remove the lower plate and the bag above so that you have access to the air passage from both ends. A hooked, stiff wire will help pull the debris out. This problem is usually cause ... Vacuums

BEAM model 178 central Vacuum. Motor will not start. Has power but just won't start. No click when switch is turned on. Is there any fuse to check? Could it be the relay? Any other thing to check? Thank you. Pierre

... Vacuums

Central vac system is 18 years old. Recently started to shut down during vacuuming. Motor may be over heating. Electrolux has been out and is pushing a new system but not sure if it is necessary.

The motor can be replaced for a lot less than the cost of a new machine. A new motor comes with a one year warranty if installed by the service tech. A new CV unit alone may be over three times as much, but does have a five year warranty.\015 ... Electrolux Cs 3000 Central System Vacuum

My Kirby G 2001 upright vacuum wont turn on. I tried another outlet and still nothing. I don't see a breaker switch anywhere. If you know of any common problems I would love to hear them. I am very mechanically inclined, I just was wondering if there are any common issues with the motors or power switches etc. so I don't waste a lot of time troubleshooting. Thanks

This might sound a bit silly but check to see if the cord is plugged into the machine correctly if it is check to see if the safety interlocks are all engaged. ... Vacuums

My Electrolux central vac wont cut off when you turn the switch off or unplug the hose from the wall. Any suggestions? Sheldon

Hi,\012The realy that turns it on is stuck... the relay will need to be replaced...\012\012heatman101 ... Electrolux Central Vacuum

I have the Electrolux Intensity upright vacuum. The roller bar underneath that is used for carpet no longer turns. I have checked the belt that is attached to it. I'm afraid that it may be the motor. Where can I take it for service or shat do I do now? Kay

... Electrolux Vacuums

My Eureka central vacuum of almost 10 years, has a reoccurring problem, of a defective relay on the pc board. The problems is usuallly the motor will not turn off. The pc board has been replace 8 times, of which 3 times were with in the last 4 months.

Are you taking the machine in to someone? or is this a self diagnosis?? \012\012What I mean with those questions is, sometimes it isn't the PC board that is causing the problem. Sometimes it is something else. Even the people that you are ... Eureka CV1804B Bagless Central System Vacuum

Electrolux Central Vacuum won't turn off

There is a relay board on the unit (where the dirt goes) There are two small wires that connect and usually a switch near by. This switch has an Auto and Manual setting. If set to manual the unit will run all the time or until set back to Auto. If it ... Electrolux Central Vacuum

Wont turn off - runs constantly - Broan-NuTone CV353 Central Vacuum

It sounds to me that the relay has stuck contacts. Try tapping the relay with the HANDLE of a screwdriver if you can find it. BE SURE TO UNPLUG THE UNIT BEFORE YOU OPEN THE UNIT !! Most centrals now have circuit boards and not seperate parts like ea ... Broan-NuTone CV353 Central Vacuum

I have a Beam Central Vacuum cleaner. I can't dislodge a piece of mulch from the rug attachment, and the motor won't turn on.

Don't know which power head you have, but if there is a base plate, take it off, you should be able to get to the debris from there. If not, remove the screws from the bottom and remove the top. Some also have a cover over the brush roll, remove it ... Vacuums

Helping out someone that has a ECV 1590A model 117A Electrolux central Vacuum. There seems to be a problem with the brushes. I'm looking for a manual or what brushes to get or a new motor. It seems to run fine what it starts.

... Electrolux Vacuums

Broken belt, motor wont turn - Vacuums

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=721048\015\012Generic problem for all Vacuums\015\012Broken belt, motor won’t turn\015\012Posted ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1311 seconds