Having problems with your Electrolux Central Vacuum ?

The reset breaker trips five seconds after turning

\015 The reset breaker on the vac trips five seconds after turning on. I can reset the breaker and turn it on and it trips within 5 seconds. I have the electrolux model E130A centralux central vac system\015

Answers :

Repair Help & Product Troubleshooting for Electrolux Central Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The reset breaker trips five seconds after turning

... Electrolux Central Vacuum

The breaker on the vacuum trips after about 3 seconds on. The canister was extremely full and started to smell like burnt wood, we fully cleaned out the unit. Now when the vacuum is turned on, the motor sounds weak, and then turns off in a matter of seconds,and we have to reset the breaker on the vacuum to get it to start again for another few seconds.

This sounds indicative of a worn set of carbon brushes on a dieing motor for a central vac. the armature is ,likely damaged causing teh breaker to blow. Please post back with more details as to make and model. Do not atempt to run the vac ... Vacuums

Vacuum turns on for approximately 300 seconds, then trips reset switch. ABout 2 minutes later the switch can be reset and the process starts all over again

... Broan-NuTone VX550 Bagged Central System Vacuum

I have a kenmore progressive 359235 vacuum with intelliclean. Has been great for about 3 years but now the brush bar has stopped turning. This is a direct drive unit with a circiut breaker reset button on top . The button is not tripped. Any ideas ?

... Kenmore Vacuums

Every time we plug in the vaccum hose into the wall recepticle the vaacuum turns on for half a second and then blows the circuit breaker. This just started a few days ago. We tried replacing the 20 am

... Dirt Devil CV950 Central System Vacuum

My e wave microwave appears to be in fine working order until the door is opened. It then trips the breaker and ceases working. Ater the house breaker is reset, the power is restored to the microwave until the door is opened again.. I havve tried plugging the microwave into another area that is on a different power breaker but again the breaker trips and the microwave ends all functions. Have you any solutions to my problem? Email Address [email protected]

You may have a short circuit on the INTERIOR LIGHT BULB circuit in your microwave.\015\012\015\012This might explain why the breaker trips every time you open the door.\015\012\015\012If so, you would have to unplug and disass ... Vacuums

Installed new VX550C central vac unit today. Breaker at electric panel trips after unit is ran one time. Reset, use once, then breaker trips again at next use.

... Vacuums

I have a kenmore progressive direct drive handi mate jr. upright vacuum. My daughter used it last night to vacuum up some cat litter that had spilled on the floor. I went to use it today and it turned on for a second and then stopped working. I have hit the reset button but it will not turn on. Help this vacuum is only 2 years old Is there anything that I need to reset or do so that the vacuum will work again?

Its probably clogged up with cat litter.might have gotten into the motor.your motor has a motor guard inside if it. when it overheats it will shut down till it cools off.you need to clean all th cat liter out of it.and clean the filters.with a direct ... Kenmore Vacuums

I opened the cannister to change the bag and when I closed it the motor switch will not turn on. The second position which turns on the attachment for rugs still comes on. We thougth it was the switch so we ordered the part and it is still doing the same thing. Is there a reset button somewhere inside? The only reset button I see is on the attachment which is working.

It can be a few things. First check the overload protector located on top of the canister. If it has tripped the unit will not run. Push it in to reset. \015\012If that is the problem check the motor safety filter to see if it is clogged and caused t ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a hoover windtunnel platinum. I have changed the bag ( hepa Q bag) but the bag light wont reset. so the vaccum wont turn on. I have unpluged it and let it set for a while with the new bag in and repluged it in. I have checked the brushes and it is all clean but it will not reset. This only the second bag so it is a new machine I should not be having problems. Is there some sore of reset button I can hit.

... Hoover Company Wind Tunnel U53019 Upright Vacuum

My vacuum stopped working and tripped a circuit breaker in my apartment. I plugged it into a circuit with higher amperage, and the circuit tripped after the vacuum ran for a few seconds then a bit of smoke puffed out of it. I assume the motor is burned out. Can I repair this? Considering buying a refurbished one for around $70 - which is probably less than round trip shipping back to the manufacturer (this is way out of warranty).

... Euro-Pro HEPA Shark EP238 Bagged Canister Vacuum

Have a hoover windtunnel platinum. I have changed the bag ( hepa Q bag) but the bag light wont reset. so the vaccum wont turn on. I have unpluged it and let it set for a while with the new bag in and repluged it in. I have checked the brushes and it is all clean but it will not reset. This only the second bag so it is a new machine I should not be having problems. Is there some sore of reset button I can hit.

... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

My Hoover Windtunnel blew the circuit breaker today, and did so again after I reset the breaker and turned off the only other appliance on that circuit. Any advice? Thanks from GrGrandma in Fremont

There could be a problem with the vac, the only way to know is to use an ammeter and test the current draw of the unit. If the vac is ok, the breaker could be failing. Plug the vac into another receptacle on a different breaker and see if it still tr ... Vacuums

Dyson 28-animal- Power brush stopped working and power light and carpet level buttons all are blinking. Per the instructions vacuum needs reset by turning it off for 30 seconds. However after doing so it does not reset and work. Help!

... Dyson DC28 Animal Bagless Upright Vacuum

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely

The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums

My brand-new Hoover Windtunnel T-Series Pet Rewind Bagless vac simply shut off while I was using it and now I can't get it to turn back on. I've emptied the dirt collection bin and let the unit sit unplugged for 30 minutes to reset the Thermal Protector as per the manual. I've even tried a few different outlets just in case a fuse got tripped, but the vac still won't turn on. What happened? Do I need to return this vac to the store? I just bought it 5 hours ago.

... Hoover Vacuums

I have a kenmore progressive vacuum with a belt reset button that trips out everytime you try to vacuum. It does it in about 5 to 10 seconds. Can I bypass the reset button or can you help me determine the problem. Thanks

A lot of times the reset button is tripping because there is a problem. The problem could be with the brush roller in this case. A lot of times I see this unit for repair and the end of the brush is so compacted with hair and debris that it has also ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

I have a Mr Coffee EMCP 50 Espresso maker. I tried to brew espresso but the coffee wasn't coming out because it was ground too fine. Now, there are 2 flashing lights one red and green-I have tried turning it off and turning it back on after waiting about 20 seconds so it will reset the pump but it is not working. Any suggestions?

... Vacuums

After using the vac for 10 minutes or so, the motor starts turning on and off with greater frequency the longer I let it run. Eventually it is on and off so frequently that it has no power. Would this possibly be the 24V relay? I have checked the breaker on the unit and it is not tripped. Does the motor have a thermal overload switch separate from the breaker?

No it dosen't. I fix central vacs all the time and relays usally don't do what you described. They either go out all the way and won't turn on or they will trip and you will have to push the breaker back in. What is probably happening is you have a s ... Electrolux Centralux Vacuum

Dyson DC24 Brush roller reset works for about 20 seconds and then trips again

... Dyson Ball DC24 Bagless Upright Vacuum

Problem with powermate nozzle keeps tripping. hit overload reset and the lite comes on and starts to work but within 5 seconds shuts down again...help

... Kenmore 22313 Bagged Canister Vacuum

Bad Motor? I have an upright Electrolux Prolux Heavy Duty "Appareil Industriel" and the motor does not seem to be working and turning the brush. Is there a trip switch somewhere to try and reset the motor? I have taken the plastic cover off on the base of the unit and cleaned it well, but can't seem to get the motor to start again.

... Electrolux Vacuums

My Shop Vac (Brand) Mdl#934-16-11 keeps shutting off while I'm dry vacuuming. I can turn it back on then it will shut off again. The filter is spotless, so that's not the issue. There isn't any reset buttons. The only thing I can think of is that the float for wet vacuuming is somehow being sucked up causing the the motor to be tripped off. The vacuum is only about a year and a half old and used only sparingly. Help!

... Vacuums

My Dyson DC24 sucked in a backpack strap and tripped. I then decided to pull out the brush and clean off whatever else happened to be clung onto it and put it back in. The darn thing doesn't turn anymore. Everyone says to push the reset button in until a click is heard but I put in a bit of force and I haven't heard a click so I stopped because I didn't want to break it. Is there something I haven't checked or do I keep adding force?

If the motor is running and the roller is not turning you may have to let the handle down as you would when you are getting ready to vacuum the flood. I think there is a switch you step on to let the handle down and it will engage the roller bar moto ... Dyson Ball DC24 Bagless Upright Vacuum

My Prosine 2.0 display panel displays Panel Fault: Memory error and the display error as well as all LEDs are off. The unit looks as if it has no power to it. I reset (power off.power on) the Prosine and all LEDs on the display (except for the back lit display) turn on for about 3 seconds then all go off again. I am able to use 120v RV Resort power and all 120v equip works. The Coach batteries do not charge and were low. I charged the Coach batteries with an external charger. The charge works ye

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0654 seconds