Having problems with your Electrolux Central Vacuum ?

Was turning on then off then back on now can not get to start at all even if i jump the low voltage line


Answers :

Ensure filter is clean. Check switch near filter.
\015\012Try reset switch.
\015\012It could very likely be the circuit board/power module in the machine near the motor. It could also be a worn out motor. It's best to take to the nearest Aerus Electrolux store and let a service tech check it out.
\015\012
\015\012For the store nearest you, follow instructions on below site.
\015\012http://www.aerushome.com/storelocator/
Repair Help & Product Troubleshooting for Electrolux Central Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Was turning on then off then back on now can not get to start at all even if i jump the low voltage line


Ensure filter is clean. Check switch near filter.\015\012Try reset switch. \015\012It could very likely be the circuit board/power module in the machine near the motor. It could also be a worn out motor. It's best to take to the neare ... Electrolux Central Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

Brush turning slowly while shampooing. It starts out fast, but after a minute or 2 the brush is not spinning very fast. I have powered it off and let it cool down. I just started out so I can't believe the engine is over heating, just doing 2 rooms, can't even get through the first room. If I take the brush attachment off, then put it back on and then turn it on, it spins fast, but after a a few minutes, it's spinning softly/slowly again. Kirby diamond edition


Track not set properly in grooves\015\012there could be a clog or the cleaner has built in feature to slow down heads for better cleaning this does it on its own ... Vacuums

Hi, I have a Xenon 600 VA sinewave inverter. My inverter starts working even when the main power is ON.So the battery gets dried up even when power is there.Can I know why this is happening? Is this due to main power line problem or a inverter problem.


... Vacuums

Vacuum motor overheating. Never happened before till last nite and today. It seems to be getting hot and tripping an overload switch or something like that. Starts back up after a long cooldown. Roller brush will still come on, even though the vacuum motor will not. Any idea what may be causing that?


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hmmm Hi there, I actually had tried everything you mentioned except for the vinegar idea which I'll do when I get back up to my home in Oregon. I checked for pinches, the heater, etc. Water does NOT come out of the accessory tool and only will dispense out of the main area for a second or two..any liquid actually starts filling up the area right behind the nozzles and around the pump instead of OUT of the machine. I checked gaskets, made sure there was a tight seal, and even made sure the little


Check the nozzles to make sure they aren't clogged. Sometimes there is a problem with the flow indicator cap, maybe too tight or not tight enough. Try squeezing the trigger while turning the can one way or the other. If at a certain point it starts ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

We have a series e rainbow cleaner. my wife had been using it i turned off and turned the canister up sie down to get the serial number. it would not turn back on.we need a new hose and thats why i was looking for the serial num. it has a rocker switch and the motor will work on low but will not run on the suction side. i have checked the wiring harnesses out as best i could without taken it all apart. im wondering if it may be the switch. it started once and then stopped.


There is one way to verify if it is the switch.It's kind of dangerous though,but not too bad.You need an extra piece of wire,fairly thick.I would use 4 guage myself.Hold it with pliers,just in case it gets hot.Turn the switch on and hold the wire to ... Rainbow Vacuums

I have two dogs and while vacuuming on the back stroke I get a black line of dog hair. I have to keep running back over the same spot to finally get it up. It doesn't do it on the forward motion, .


That's natural.. vacuums pick up the dirt on the back motion (going against the grain) ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have an upright, but use it as a canister. It will start sometimes and vac for about half and hour and then it will quit. I can't get it started again even after it cools off.


First check the hose and down by the brush roll for a clog. If there is a clog, it will cause the motor to overheat and the theremo protector will cause the motor to shut off until it has cooled. Now if it won't turn back on, the thermo protector m ... Electrolux Vacuums

I am very unhappy with my Kirby. It's nothing like the demo they showed me. It won't even get lint off my bedroom carpet and I only had it for less then 2 months and the belt broke. I want my money back and I'll give the Kirby back!


Give it back to your kirby dealer. ... Kirby Vacuums

As you turn the Sebo on, the 2 red lights flash once and there is no motor. If you rotate the brush roller the motor starts. We've taken off the brush roller and put it back on and now it doesn't even start when you rotate the roller.


... Sebo Automatic X1 Bagged Upright Vacuum

My dyson hand held shuts down after about 30 seconds, It turns back on again, but it does this over and over again, even after being fully charged with caontainer emptied. Its almost like an overheating thing, but different since it starts right back. It is annoying.


... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

Thanks! Awesome tip to get into the gear box. My roomba would start up but would move very sluggishly. Looked up the beep code and it was the brushes. Brushes are cleaned regularly so it was something internal. Did your solution of getting into & cleaning the gear box and viola! He's back!


... Roomba Robotic Floor Bagless Vacuum

My Dyson animal seems to have an electrical issue that I am unable to pinpoint. Neither the wand nor the floor vac have any suction AT ALL. In fact the vac makes absolutely no sound and you wouldn't even know that it had power to it unless the rollers are turned on, the rollers work just fine. I had this problem start about a month ago and then it just started working again after messing with it for a while, now it has happened again and I am getting a little agitated! Please Help!!!!!!!!!!!


There is a filter inside the canister, and by your description it sounds like it needs to be cleaned. if you remove the filter and blow it out using a air compressor or using a slightly ridged brush and tapping the filter out this should solve your ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The brush is not moving on the vaccume. I'm pretty sure that the belt is busted. I cannot see how to get the shroud off, so that I can get to the roller and belt. It all looks and feels like one piece, even when I start removing screws. It is a bag-less vac. The model number is - v1310rs. Thank you.


I know on my Eureka I had to remove a couple of screws on the bottom and then get a flat blade screwdriver and wedge it on each side of the base kinda next where the end of the roller would be and it snaps up and off. Really weird I thought but that' ... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

My Kirby Heritage II vacuum is not picking up dirt up out of the carpet like usual, and I have to keep setting it lower to pick anything up. I finally get it to such a low setting that it starts sucking the carpet up and makes a whirring noise, and starts smelling. Every time this happens, we find the belt has been burned. We are wondering if the brush roll inside with the brushes that pick up dirt are worn out and too short?


... Kirby Heritage II Vacuum

Can't reassemble!!! Long story as short as possible- I removed the hood from my Bissell 1699 and can't seem to get it back on correctly. The "Smart Mix" knob and it's parts seems to be the problem. How does this line-up, or what is the best way to put it all back together? Thanks, Josh


The piston is put on the bottom of the smart mix knob, turn the knob to the water only setting, then put the top housing back in place making sure that the piston went into the slot, after the top is all of the way down, turn the knob, if it turns ea ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Floor Attachment I took off my floor attachment, but now the belt seems to be off and I can't seem to get it back on right. I can't use the attachment and I don't know why it's so hard to figure this out. They say, just turn it to belt off, but when i turn it it lift's it up and can't line up with the belt off label. Then, when I turn it the other way, it's off. So I've been trying to pull it off so when it lines up with belt off, it's off. But the I turn it the other way and it's still off a


Try this,\015\012\015\012With the floor nozzle off the machine spin the belt lifter around until the red arrows match. If you look at the side that attaches to the vacuum you should be able to see the belt up on the hook. If is not on t ... Kirby Generation 3 Bagged Upright Vacuum

I installed a new battery in my Roomba 540. It charges and runs directly with power cord but will not charge on dock. When I push the dock button, it acts like it "sees" the dock and approaches it and even slides on, but then gets back off again and just keeps going back and forth until I turn it off.


... Roomba Robotic Floor Bagless Vacuum

Eureka 2961AVZ Will not start ...I get a momentary flicker of power about every 3d or 4th time that I flick on the power sw. Outlet is fine / Plug looks good / chord looks good / I see no obstructions ........Would appreciate any helpful thoughts ....Trying to get Mom's Eureka 2961avz back up and running. Thanks


CAREFUL! This is how my problems started. The cheap switches (and wiring) Eureka is using in some models, especially my model) should provoke a lawsuit imo.Here's my story, just in case it might help. Mine started with a problem very similar ... Eureka 2961AVZ Bagless Upright Vacuum

The valve pipe assembly just popped off our Dyson DC 17. How do I get it back on? I see it appear the arm of the assembly needs to be captured but I can't figure how to get it all lined up without forcing it together.


... Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum

I have a Z5930 vacuum and i want to trace an electrical fault. I need to disassemble it to get to the electrical connections and it is quite a tricky one to get in side. The machine will run and then cut out after a short time. It will then re-start in about 2-3 minutes and run normally again and so on. I was not able to give you the exact model but it is Ultra Filtration Oxygen line


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

My handle won't go back up after an extended vacuuming session during which I used the hand/broom/animal hair attachments several times, thus pulling the hose out/putting it back in, starting/ stopping, and suddenly no matter what I do short of forcing it (and even if I try forcing it a bit) I can't raise the handle to put it away.


Do you know what model number Dyson you have? Is it the ball style one? Just find a similar product here on this page and let me know what model number is closest: ... Dyson Vacuums

No Suction I get great suction in the hose, but when I plug the hose back into the unit, there is no suction and the air flow indicator line goes completely red. I've changed the bag and filters. I took the small panel off the back and made sure there is no clog, and took the hose off to make sure there was no clog there. Still no suction. Please help.


I about to say that's always a clog of some sort that causes that ... Miele S7210 Bagged Upright Vacuum

It starting to put out a hot type smell. I have tried cleaning the filters real well and even tried to see if there was problem with the ozone filter. We have checked and could not find a jam. I know the hose has excellent suction. The vacumn works but the intelliclean sensors will not. It only takes about 15 seconds or so for the odor to start. Then it gets real strong and it makes my eyes water


Hi,The hot smell could be from the belt or the motor. Turn it on for a moment, turn it off, then flip it on its side and smell the belt that drives the brush. If that is where the smell is coming from, then your belt is burning up. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0656 seconds