Having problems with your Electrolux Central Vacuum ?

I have to go into the garage to turn on the motor on the tank and to shut it off. When I plug the hoses into the outlets in the house, it doesn't turn on the tank motor. I don't know what part to get and nobody in Raleigh, NC shops can help me.


Answers :

Is this Electrolux that's now known as Aerus? If so, take it in to the Aerus Electrolux store for a tech to look at. You can find the nearest Aerus Electrolux store by following the instructions on the site at bottom of page.
\015\012
\015\012It sounds like a problem with the power module in the vacuum. Without checking for myself, that's my best guess.
\015\012
\015\012http://www.aerushome.com/storelocator/
Repair Help & Product Troubleshooting for Electrolux Central Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have to go into the garage to turn on the motor on the tank and to shut it off. When I plug the hoses into the outlets in the house, it doesn't turn on the tank motor. I don't know what part to get and nobody in Raleigh, NC shops can help me.


Is this Electrolux that's now known as Aerus? If so, take it in to the Aerus Electrolux store for a tech to look at. You can find the nearest Aerus Electrolux store by following the instructions on the site at bottom of page.\015\012\01 ... Electrolux Central Vacuum

We have an Ebac Homedry 660 dehumidifier. It makes a noise when started and the red light indicating water tank full comes on. It has been inspected by a local repair shop and we have been told that the 'Fan' is not working. The workshop does not know how to get a spare part. Who is the repair agent in Auckland, New Zealand?


... Vacuums

My Hoover Dust Manager roller brush is not turning It may be the belt but I dont know how to get to it to replace i Can you help Michelle


... Hoover Vacuums

My shop vac blows dust as soon as it's turned on and throughout use. I have changed filters, nothing is helping. What part of my vac can not get wet, or is there a better way to clean out the system?


There should be a cover or sock over the filter,this will stop the dust.the paper filter is the part that can not get wet. if you don't have a cover for your filter use an old sock or something simular to a sock. ... Shop Vac 584-04-00 Quiet Canister Wet/Dry Vacuum

I have a fake nokia n8 cell phone(basically called chinese). i didnt know about flight mode and turned it on by mistake. now i dont know how to turn it off. menu is not opening and i cant make a cal... plz help me out.. :(


Take the power button should give you the option to turn off airplane mode ... Vacuums

My Hoover Wind tunnel has even a cheaper on/off switch and now, you can't buy a new one. I used to go to their website which had a wonderful diagram of the 'guts' but now the only parts are the obvious ones, belts, filters etc....I have to vacuum twice a day and I should be the test person cause its on and off on and off, but now for a vacuum I purchased 3 years ago for over 200 bucks and I can't fix it myself really makes me made or do you know where I can get this part? help? if not, I will ne


Have you tried going to appliancezone.com? I go there when I need parts... ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

I would like to know where i can get a manual for the bissell 3760-4 model. i bought this sweeper used and i would like to get a book on the parts . thank you for your help


BISSELL User’s Guides can be downloaded at www.bissell.com\015\012On the front page under Customer Service click on User’s Guides and enter the model number of your unit.\015\012User Guide will be displayed as a PDF file. ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

Need to open rotating brush part of vacumm as motor functioning but roller not turning...perhaps belt broken put need to get into ..inside brush box ...Need help need instruction with diagrams Thanks for help Robert


... Panasonic MC-V9638 Bagged Canister Vacuum

My Dyson vacuum works fine for cleaning the rug but the hose doesnt get any suction at all. I removed the hose and all the parts around it that I could and dont see any clogs or broken pieces. I lost my manual so I dont know if this is addressed, or if there is a switch Im not flipping. Gave it a thorough look but found nothing.


Hi there,Sorry to hear you're having a problem with your DC07. If you have suction through the cleaner head but not through the wand, it sounds as though you have a blockage. Although you say you've already checked for these, you may find ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Bissel proheat 7901 carpet cleaner and it is not sucking the water up. Normally when I clean the water gets sucked back up and I have to empty the dirty tank. Now no water is in the tank when I am done cleaning. Please help I cannot afford to take it to the shop.


I'm not sure if this will help but I had the same problem and was about ready to pull my hair out. I ended up taking the fill tank off and if you look inside where the red overflow flap is you will find a small screened opening. I found that mine w ... Vacuums

I have the brother Ls-2000 sewing machine i threaded the top as well as the bobbin but when i try to sew the thread gets stuck and it bunches up and tangles in the bobbin. also the little bit that did sew was tight stitches on one side of the fabric but very loose on the other side I followed the instruction and it keeps happening i need help i dont know how to fix it please help me


Adjust your tension.You probably did not wind your bobbin properly as well.Make sure you oil your machine every month or so and make sure your bobbin is seated properly before you sew.\012\012Go slower with the pressure foot speed and use the r ... Vacuums

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

Kirby G3 I threw out my last bag for my kirby. I have an other model and now i dont know which type I need to get. I have 4 Style #2 bags but they are not the right ones... Help!


Beginning with the G series, G3 and G4 had round openings for the dirt intake. Prior models had oval so they will not fit, so find G3 or G4 bags and you will be set ... Kirby Generation 3 Bagged Upright Vacuum

Help I live in kansas city kansas and I was wondering where there is a shop that I could take my carpet cleaner to and have it fixed. I think the water hose is clogged and I don't know how to get to it.


Call Bissell at:Service Center Dept. Phone Number:(800) 457-1509\015\012They will give tell you where you can take yours to for repair. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My eureka optima upright bagless vaccum has VERY low suction using the floor part. the hose has excellent suction. i removed the little translucent door underneath and there were no blockages, i cleaned the brushroll thoroughly and that hasnt helped either. i know this probably isnt recommended but i turned it on to the floor setting with the brushroll off and stuck my fingers up the intake as far as i could, the suction was good further up but it just seems to stop down at the base. because i s


I will try and help here. Is the sole plate on the bottom of the vacuum complety on and there are no visible cracks along the seam where it meets the body? This is the usual cause for this. Onc you take of the plate to access the roller and brushes, ... Eureka 431A Optima Bagless Upright Vacuum

My Dyson animal seems to have an electrical issue that I am unable to pinpoint. Neither the wand nor the floor vac have any suction AT ALL. In fact the vac makes absolutely no sound and you wouldn't even know that it had power to it unless the rollers are turned on, the rollers work just fine. I had this problem start about a month ago and then it just started working again after messing with it for a while, now it has happened again and I am getting a little agitated! Please Help!!!!!!!!!!!


There is a filter inside the canister, and by your description it sounds like it needs to be cleaned. if you remove the filter and blow it out using a air compressor or using a slightly ridged brush and tapping the filter out this should solve your ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My 88 year old mother bought a Dirt Devel DHC001 - has been used twice but it looks blocked and has no suction but there is suction at the pipe end if I take it off. I have opened the red end and emptied out but there seems to be dust in the rear part and I have no idea how to get it out. The shop she bought it off thought they were being helpful and removed all packaging but seem to have taken instructions as well.


To answer this properly, I am going to need the actual model number on the bottom of the unit on the silver/metallic sticker. Usually MO###### If you can get that I can help you out further. \012Mark ... Vacuums

Help the roller isn't turning and I want to know how to get if off also to change the belt.  I don't have the manual, the kids stored it somewhere


With a Kenmore Canister, on the power head, there are usually 2 screws on the bottom of the unit. You must remove both screws and unlatch the top cover; first from the back by the swivel and secondly on both sides of the power head. Changing the bel ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a champ thermos and the stopper is broken do you know where i could get parts. it is made by hanbaek 3606A 21156 does this help it is 1 litre capacity


... Vacuums

Plug Part # 8191782 on my kenmore vacumm wand is bad, I dont know how to get the wand apart to change it


... Kenmore Vacuums

A small belt fell from underneath my bissell steam cleaner and I notice the brushes no longer rotate when I purchase the part where does it go? I tried turning it up side down to find out where it came from don't know because there is a compartment for the belt access but that particular bet is not broken. It's a very thin belt I can not make out the number located on the belt please help.


If you are unsure about where it goes it may have a diagram in the owners manual. When you say you saw a belt in a compartment are you sure that it is not an extra belt you are seeing as they often give an extra in the machine kept in a compartment l ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Our problem with our Rainbow E Series is that it has sucked water up and blown it out through the lower part of the hepa filter, making the filter wet and dirty. This had happened before and the repair shop did not see any problems with the machine, so we replaced the filter and were very carful not to overfill the tank and to change the water often. Now it has happened again and ruined another filter. Do you know what could be causing this issue? Can the filter be cleaned or will a new one be


Thank you for allowing\012us to help, please respond with further questions and concerns\012\012Spanish speaking\012available for all problems\012\012 ... Rainbow E series Canister Wet/Dry Vacuum

Oreck vaccum when i put a new belt on, the belt rubs the side of the wall of the vacuum gets real hot and busts. is there any type of washer fitting that goes on the vacuum to hold the belt in place? i dont know i need help thank you. you can reach me at [email protected]


The belt must not be running true to the pulley. You may need a brush roll, but also check the motor to make sure it isn't moving inward after the belt is put on. ... Oreck XL Ultra Bagged Upright Vacuum

My vacuum is not sucking theirs a yellow pellet that indicates the air flow. And when i turn it on it moves and i think thats part of the problem i don't know what to do i lost my manuel help.


Try emptying bag. then clean filter. then unblock hose using a broom handle. let us know how it goes. ... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0986 seconds