Having problems with your Electrolux Central Vacuum ?

My Electrolux central vacuum power nozzzle was working hit/miss and now has stopped working. The metal connectors in the wand and power nozzle get very hot, enough to burn. The metal connectors also

\015 Electorlux central vacuum model number E130A, power nozzle model N106M. I replaced the circuit breaker in the power nozzle head in 2009.\015

Answers :

Repair Help & Product Troubleshooting for Electrolux Central Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Electrolux central vacuum power nozzzle was working hit/miss and now has stopped working. The metal connectors in the wand and power nozzle get very hot, enough to burn. The metal connectors also

... Electrolux Central Vacuum

On a Kirby sentria the metal spool sticking out that goes into hose or power head becomes extremely hot and left burns marks on brush tube. It only gets hot when using power head. I checked all adjust

Check the brush roll to be sure it's spinning free too much drag can cause that to get hotter but usually it would break the belt. That spindle will get hot from the friction created by turning the belt and from the motor's heat. They'll just get hot ... Kirby Vacuums

Power nozzle on E-series won't start when cold unless the red 'reset' button is pressed multiple times while also holding the trigger to 'warm it up'...this is w/the power nozzle off the floor - no restriction on it turning. Once it's been running and then turned off the button must be pressed w/the trigger to get it to run - again w/the nozzle off the floor. It also seems to shut off too easily while vacuuming. I replaced the motor,which didn't fix it. Is the reset switch next on my list? T

... Rainbow E series Canister Wet/Dry Vacuum

I have a hoover mach 5 multi-chamber cyclonic vacum cleaner and it keeps getting hot and quitting.it's got a strong smell like something is burned when it gets hot also.

If its giving off that strong smell then the motor is bad. probably caused by not keeping the filters clean. on any bagless machine one has to clean the entire vacuum after almost every use to keep the unit operating correctly ... Vacuums

Electrolux Renaissance power nozzle turning on and off, brass pins hot

The deal with the Renny is that it runs off of circuit boards. Usually the problem of the main motor shutting on and off is caused by one of the Triac boards located inside the canister. Another problem could be the thermostat wire located on the i ... Electrolux Guardian Bagged Canister Vacuum

I have a kenmore 116.25615506 vac and I want to replace the connector on the power sweeper. I cannot figure out how to disassemble the "electric folding wand" to get the connector out

... Kenmore Vacuums

I'm using Miele Medivac vacuum and I just sucked in a small plastic eye drop container by accident(I sometimes take off the brush part to **** in 'small enough' articles). And it is jammed in the part where the plastic hose connector bends. I think I can take it out if I can just disconnect the long necked plastic hose connector that connects the metal wand part and the hose part. Is it designed to be disconnected or should I not even try it?

I love the fact that the filter bleeped out s.u.c.k ha ha! ... Vacuums

Hi, I have a Kenmore vacuum cleaner model number 20712008. There seems to be a problem with power getting to the suction base. There may be an electrical problem with the connector between the metal tube and the base.

... Kenmore Vacuums

My wife's Viking 6690 smoked this last weekend. I opened up the end where the power switches are and the board had a 0.01 ufd capacitor the blew up. That would be easy enough to repair. However when the Cap blew, it also fried a small quarter watt resistor that sits just under the upper white pin connector on the board. The resistor is burnt beyond recognition and I am trying to find its value. Is there a schematic available for that board or a closeup picture of the board so that I could

According to you your machine's resistor burnt out. This resistor is located above the 240 volt capacitor which white base. change the resistor soon. For color code of the resistor you can follow the ... Vacuums

I have an electolux EL7001 canister vacuum. When I attach the large power nozzle....the one for the carpets not the small one for the floors...the nozzle is not powered unless I strap it on with duct tape. Is there some piece I can purchase that will secure the connection between the wand and the power nozzle head so that it is powered without the duct tape?thank you.

... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

No power. I was getting intermittent power with my miele s558 midsize canister, but it was predicated with me fiddling with the retractable cord to get it to come on and then not move the canister while I was vacuuming. Now I can get no power. I have taken it apart and can see no issues with connectors, cord, casings, etc. It all looks fine. It is about 5 years old and I have had no problems with it.

... Miele S558 Red Velvet Bagged Canister Vacuum

I just purchased a Sebo Airbelt D canister vacuum. I plugged it in and used it for ten seconds then turned it off, retracted the power cord and now cannot get the power cord out of the machine. Did I not spend enough money to get a quality product? Does anyone have any idea how to get the power cord out without breaking the machine?

... Vacuums

Electrolux 2100 power nozzle motor doesn't run

... Vacuums

Electrolux Epic 6500 SR ...no power to power nozzle. I think it is the switch in the handle because if I use my friend's hose/handle (same model), my power nozzle works fine when I turn on the switch. If you think it is the switch, can I get a part for it?

That's about the best one to narrow down a problem, however, there could also be a break in your hose wiring. Switches, hoses, and hose handle assemblies are all available at your local Aerus Electrolux store. Simply take your entire machine in so ... Vacuums

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u

Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums

My Kenmore 116.25812508 power nozzle motor will not run unless I tilt the handle. I checked the connectivity from the circuit board in the power nozzle base to the telescoping wand with an ohm meter and there is no indication of disconnect.

I have had this vacuum for about 3 yrs and nothing but issues with it. It's been in the shop already once and it needs to go again. No power in the power head. A wheel came off of the powerhead too .. keep snapping it back on but it always comes off. ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

How do you take apart the wand and Power Nozzle of the Perfect Power Nozzle

... Perfect ppn-1 power nozzle, w/wands 15widegear belt breaker blk

Power Nozzle Model No. N137A (for Electrolux Epic Serial 6500 SR) has a broken wire. Can I get a replacement power nozzle or find a repair place in the Everett, Washington vicinity?

... Electrolux Epic 6500 Vacuum

Burned out The best way for me to describe the problem is to post reviews I made on Amazon.com, which is where I purchased them. ________________ Based on my past experience, I bought another 6 months ago. I live in a very tiny 2 room apartment and do not vacuum lots of dirt. I noticed this new vac getting very hot to the touch where the motor is located with only a few minutes of use. Today it just STOPPED. When I felt the canister, it was HOT. It obviously has burned out. Upon closer inspect

... Euro-Pro HEPA Shark EP238 Bagged Canister Vacuum

Power nozzle for rainbow vaccum is getting power but the motor does not work nozzle model r-2800c

Hi there it's SmartAlec from NelsonVacuums.com.au here. It will either be the fuse or the motor itself. If you disconnect the wires from the fuse and join them together and ... Vacuums

Power nozzle omni-flo plugged - goes into 1990 electrolux H684350. How do I get power nozzle cover off>

... Electrolux Vacuums

How do I replace or repair my tristar power nozzle cordI don't know how to get to or how difficult it will be. there is a short in wire because it is separating from the power nozzle.

Dear kerri_clark,Can't you take a picture of tristar power nozzle cord that you mean.I need to take a look at this to assist you further more.regards,dm ... Vacuums

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!

Great. ... Kenmore Vacuums

Burning belt, I also ned to get in to where brush is.

The manual for your Fantom Thunder can be found by clicking this link on my business web site: http://www.sewvac1.com/Fantom_Thunder.pdf ... Vacuums

The metal attachement wand keeps getting stuck

This has been a major problem for all dysons. Spray a little furniture polish on the tube and it will slide in and out better. ... Dyson Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0766 seconds