Having problems with your Electrolux Central Vacuum ?

Can the damaged hose 8 inces from handle be cut then replace hose

\015 Crushed the hose of central Vac about 8 inches from top of handle. Can the damaged hose be cut and replace the remainder back into the handle?\015

Answers :

If the hose is non-wired then you can fix this yourself. When you Plug the cuff into your wall inlet does the vacuum turn on automatically? If so then you should be able to trim the hose with no ill effects other than losing eight inches of cleaning area.
\015\012If the hose has a switch on it's handle that turns the vacuum on and off, you will probably need a technician to fix the hose. Some wired hoses even have High Voltage lines in them and should never be taken apart.
Repair Help & Product Troubleshooting for Electrolux Central Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Can the damaged hose 8 inces from handle be cut then replace hose

If the hose is non-wired then you can fix this yourself. When you Plug the cuff into your wall inlet does the vacuum turn on automatically? If so then you should be able to trim the hose with no ill effects other than losing eight inches of cleaning ... Electrolux Central Vacuum

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each

Should be a pry off dot on the underside revealing a screw ... Vacuums

I have a electrolux oxy3 system vacuum cleaner. The floor is damaged, and the hose has been damaged and severed and the copper cables have been cut...so I need to purchase a replacement foot and hose/hand piece. regards Sandy

... Electrolux Vacuums

I am replacing the hose on my kenmore canister 11622612200. i easily replaced the handle end of the hose, but cannot see how to replace the end that goes into the canister. can you tell me how to disassemble the canister end for the new hose? many thanks!

Open the canister and locate the hose intack. There is a plastic retainer which slides over the end of hose and is secured to the body of the canister with a few screws. Remove the screws and pull the retaining ring up to release the hos ... Vacuums

My vacuum hose has split very close to the handle- how do I remove the handle, cut the hose at the split & reattach it to the handle unit - Centralux central vacuum system. Where can I find a diagram of how to remove the handle?

Do Not Cut the hose! It has wiring inside to control the vac and power head. This is a swivel handled hose with both low and high voltage contacts in it. The same wiring which gives the hose its ribbing, is conducting current for two applic ... Electrolux Centralux Vacuum

Have a Miele S658 Blue Moon that cuts out intermittently, sounds like most of the solutions to similar problems indicate the circuit board has gone bad in the hose mechanism.......can just the circuit board be replaced or does the entire hose have to be replaced?

Probably needs a new hose. ... Vacuums

Where do you hook the clear hose that is in the compartment with the motor ? Second where the vacuum hose connects to the bag it keeps cutting in and out of power. I replaced the female cord to motor and still cuts out."no suction "

Would you care to tell us the make and model of the vacuum you're asking about? ... Vacuums

How do I replace the handle on Electrolux 1205 powered hose?

... Electrolux Canister Vacuum Cleaner Wand Silverado, 1205

My 8 yr old kenmore vacuum works well - however the hose has worn under the handle where there is a hole (resulting in decreased suction power). I'd like instructions on opening the handle and bypassing the worn piece of tubing rather than replacing it for $129. Some of the handle screws remove easily but the last one doesn't loosen easily.

Hi,Have you tried spraying the stubborn screw with WD40 and let it soaked for a while? Other than these screws holding the handle together, there would no other way of opening it up. Hope this be of initial help/idea. ... Kenmore Vacuums

My Dyson DC20 motorhead vacuum has a blocked hose - how can I unclog this? I think there is a sock caught up by the handle. The hose has electrical wires running through it so I cannot cut the hose.

Usually a plugged hose can be cleared using a broom handle, if you can force the blockage through, if not as previously suggested a coat hanger attached to the broom handle (duck tape will do) straighten out hanger so it can be used like a cork screw ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

The small button on the hose handle is missing, I need a replacement

... Euro-Pro EP923 Canister Steam Vacuum

Where can I purchase a replacement wire for the handle of my aerus centralux hose? It's the black wire that runs from the switch in the handle and attaches to the pins in the wands.

Any Aerus Electrolux store should have them in stock.\015\012You can find the one nearest you by following the directions on the below site:\015\012\015\012 ... Electrolux Centralux Vacuum

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?

Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

Lindhaus- replace hose to handle_ hose came out - difficult to screw back in-

... Lindhaus Diamante 300 Upright Vacuum

Dyson DC14 won't change suction from hose to floor tool after hose is replaced in handle

Try cleaning everything in the vacuum cleaner, hoses and filters and where you collect the dirt. Something must be plugging it up. If you have any brushes check to see if thread or hair is rolled around into it. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

The extension wand is stuck. It will go up to a certain point and stop. The gray flexible hose that it is housed in is not damaged and there is nothing on the steel metal rod that slips into the hose that I can see. The gray button on the handle still depresses as well and everything is still "Clicking" as far as the button. thank you

I would try the dyson medic .com this is the place that specializes in the dyson vacuum. Good luck ... Dyson DC25 All Floors Bagless Upright Vacuum

Wondering if the head is plugged up because it makes a sound like air is escaping somewhere. I've replaced the original cloth bag with a comparable "O" paper bag from Sears. I tried to see if there was a clog in the hose by placing a broom handle in the hose to see if something would loosen. I also cleaned the filter and the air filter. If the head is plugged, how can I fix it? We can't get the vacuum apart. Thanks.

I had this problem, but suction improved when the attachments were properly secured in their holders. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

I want to replace the hose but do not want to buy the handles, where could I buy the hose for Sharp part number 9HMSHPPAR7430?

Man that stinks burden.\015\012\015\012Here's the deal. Sharp quit making vacuums and parts because, the same factory they were making the vacuums in, they were making regular T.V.'s in, and they decided to focus on the flat screens, thus ... Sharp Vacuums

Hoover F8212-900 Agility steam vacuum - problem reassembling handle parts (clean spurge button, spring, etc.) after replacing lower short hose.

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

When I vacuum with the power nozzle, it keeps cutting off. Do I need to replace the hose or the power nozzle?

Not necessarily. It's hard to tell without checking it out. I strongly recommend taking it to an authorized Aerus Electrolux store and letting the service tech check it.\015\012If you have the "Sidekick", you can try using it. If it still cu ... Electrolux Epic 6500 Vacuum

DC25 telescoping handle does not seat tightly. When pulling the vac back it unseats about 2 inches. This prevents the hose from engaging securely in the base and suction is affected. Do I need to replace the clear wand release catch? I've only had the vac about a year and am surprised it would wear out so quickly.

... Dyson DC25 Vacuum

Need a replacement handle for the hose on the EIO Varia Estate Vacuum.

... EIO Estate Bagged Canister Vacuum

I broke the end of the hose on my Dirt Devil DD2230 Cylinder vaccuum just where the handle goes into the extending brush bit. Can I get a replacement?

I just checked with DirtDevil on this hose, and they say it is no longer available. ... Vacuums

I have an Electrolux Epic 6500 SR vacuum and the hose end with the handle is separating. Power nozzle losing contact intermittently. Is this piece replaceable or repairable?

It is replaceable. Just take it to the nearest Aerus Electrolux store and the service tech will take care of it for you.\015\012Go to the following site and follow instructions to find the stores nearest you. ... Electrolux Epic 6500 Vacuum


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0728 seconds