Having problems with your Electrolux Centralux Vacuum ?
I need a hose handle for a centralux hose. Where can I purchase one?
Repair Help & Product Troubleshooting for Electrolux Centralux Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I need a hose handle for a centralux hose. Where can I purchase one?
... Electrolux Centralux Vacuum
Where can I purchase a replacement wire for the handle of my aerus centralux hose? It's the black wire that runs from the switch in the handle and attaches to the pins in the wands.
Any Aerus Electrolux store should have them in stock.\015\012You can find the one nearest you by following the directions on the below site:\015\012\015\012 ... Electrolux Centralux Vacuum
I have a vaporetto Q94197and need a new hose. Where can I purchase one in Australia please?
I have a Broan Nutone central vacuum. The power head seems to stall unless you lift up on the handle. I think I may need to change the belt but cannot find a place to purchase one to see if this is the problem Model number BN180 type 1
You are correct, you need a new belt. You can find belts for the Broan BN180 at www.vacbelts.com. ... Vacuums
I need to replace the hose that comes out of the shower and connects to the shower head. Where can I purchase one?
You can find them at Lowe's or Home Depot or most any hardware store.\015\012You might be able to find them on line if you go to Google and search under the brand name you have, such as Waterpick.\015\012\015\012If you find this solution to be ... Vacuums
I need to reassemble my rainbow e series electrified hose handle
Yes, it is a ground wire. When you put it back together, make sure that the two halves of the hose handle are holding the wire up against the metal. I just had one apart the other day for the first time and if I recall correctly, the wire goes near t ... Rainbow E series Canister Wet/Dry Vacuum
My vacuum hose has split very close to the handle- how do I remove the handle, cut the hose at the split & reattach it to the handle unit - Centralux central vacuum system. Where can I find a diagram of how to remove the handle?
Do Not Cut the hose! It has wiring inside to control the vac and power head. This is a swivel handled hose with both low and high voltage contacts in it. The same wiring which gives the hose its ribbing, is conducting current for two applic ... Electrolux Centralux Vacuum
Pls Help! My Dyson DC05 (Yellow) needs a new wand. Am unsure whether it is the assembly wand or hand one found in spare parts. The wand I need to replace connects the two long hoses together, and NOT the wand which fits onto pickup head. M.thks if you can advise which one I need. Getty rather dusty in my pad!!
... Dyson DC05 Bagless Canister Cyclonic Vacuum
My BROAN CV-110 hose with the rug beater only works if I turn it on from the base unit. Shouldn't it turn on when I plug the hose into the wall recepticle? Do I need to replace the hardware at the end of this hose and if so, where would I purchase that? This central vac came in a house I just purchased. Thanks for any help. Sherry
... Broan-NuTone CV450 Central Bagged Central System Vacuum
I am looking for a Hoover Steam Vac Bare Floor Attachment, Part #90001331. I found one in the US for $8.95 but by the time I paid shipping and handling it would cost $91.77, a little ridiculous. I am looking for one in Canada. Can you help. I have heard Hoover has been bought out and parts are very difficult to purchase. I bought this 1 month ago and I'm sorry I didn't know this prior to purchasing.
Hoover Bare Floor Attachment F5XXX from Usavacuum.comIt is $6.99 and shipping should cost you le ... Hoover F5906-900 Upright Steam Vacuum
I have lost the manual and forget how to use the hose part of vacuum, also the handle turns and is not secure ( that is the handle in the upright position). It is a bagless Stick Shark Vac. I need to know how to attach the hose to the vac so I can clean furniture and corners.
... Euro-Pro V1828 Shark Stick Vac Bagless Vacuum
Need Charger for Shark: Charger # KA12D090015023U and Im sick and tired of looking for it. It shouldn't be this hard This shark was purchase by my mother who is 85 years old from HSN, she bought 2 one for a gift and one for her self. Somehow the charger got damaged and I cannot find one any where please assist me in finding this item. This Vacuum has been used one time. I hate to contact Home Shopping Network
Call 1-800-798-7398 the person I talked to was knowledgable. The cost of the charger KA12D090015023U is $14 including shipping and takes 2 days to deliver. ... Vacuums
I need to change out the short hose on the underside of my older Dyson DC 07 Animal (Light Purple). It is the one less than a foot long on the underside which is attached on one end to the main body of the vacuum(I was able to remove this one) and the top of the upper soleplate. The latter one seems to be glued or otherwise permanently attached.Any assistance you could give me on this would be greatly appreciated....Thanks
Hello Cynthia,\015\012\015\012It's not glued, but it can be a little difficult to remove. You need to twist and pull at the same time and it should pull off. If it's being stubborn, squirt a little bit of WD40 / penetrating fluid where th ... Vacuums
I have a Europro steam cleaner, model # NH15,,EP923F, I need the lock button on the handle of the hose that locks the accessories. I have phoned and emailed with no success .Can you help he
... Euro-Pro Fantom Steam Cleaner FC905K Vacuum
My 8 yr old kenmore vacuum works well - however the hose has worn under the handle where there is a hole (resulting in decreased suction power). I'd like instructions on opening the handle and bypassing the worn piece of tubing rather than replacing it for $129. Some of the handle screws remove easily but the last one doesn't loosen easily.
Hi,Have you tried spraying the stubborn screw with WD40 and let it soaked for a while? Other than these screws holding the handle together, there would no other way of opening it up. Hope this be of initial help/idea. ... Kenmore Vacuums
I have a kenmore progressinve 22813. The hose ripped at the swivel head. I purchased a new hose but can't separate the old hose from the swivel housing. How do I do that? do i need to buy all the swivel head parts as well? Thanks
Usually when you remove the hose from the swivel base and try to attach the new hose the attachment is usually not tight enough therefore the suction is always low. It is better for you to purchase the swivel head parts to enable you enjoy the use of ... Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum
I broke the handle part of the shark steamer #53101. I don't have the book to try to tell you the parts I need. Can you send me a picture or a copy of the steamer. It is purple. The above number may not be the correct one. It is broken in the center part. It has a little small circular piece that joins the two pieces which are broken. The beginning of the handle at the bottom of the steamer and the next session which has the steam release. The top of the handle is okay . It the middle and bottom
Hi,Ann there are very few parts for these...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
I RECENTLY PURCHASED A HONEYWELL 2000i INVERTER GENERATOR AND I HAVE LOST THE USERS MANUAL SOMEWHERE IN THE HOLIDAY MESS. I AM LEAVING ON A TRIP IN A WEEK AND A HALF WHERE I WILL NEED THAT MANUAL. I'M NOT HAVING ANY LUCK FINDING ONE ONLINE AND WAS WONDERING IF YOU COULD DIRECT ME TO WHERE I COULD FIND ONE, OR SEND ME ONE. PLEASE! I WOULD APPRECIATE ANY ASSISTANCE. THANK YOU. .MICHAEL ALLISON [email protected]
You will need to contact Honeywell at this link below and fill in the form to request a free user manual for the Honeywell 2000i Inverter Generator:\015\012\015\012 ... Vacuums
DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each
Should be a pry off dot on the underside revealing a screw ... Vacuums
Suction I too have the same problem as Mr. Chief. I followed your advice and checked all the hose attachments, no clog. Tthe only one hose that the broom handle would not pass through was the plastic hose and there is a curve in that part. I did not want to force the broom in there as this is a new vacuum and is probably under warranty.
If you have a plumbers snake you can use that. But being under warranty, I would take it to Sears for repair. ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum
I have just purchased two (2) Electrolux Nimble vacuum cleaners. Not one, but both, straight out of the box, the beater bars will not run. It turns on, select carpet, and lower the handle, the red light to check beater bar/or filter lights up. You can reset the light by unplugging the unit, then plugging it back in, but with same results. Now the kicker, if you take out the handle, select carpet, lower the body by the carry handle, it will run and operate correctly, however, as soon as you r
Hi: My DC14 (not animal version) has 3 major cracks that have pretty much killed the thing. There are three 'columns' that run down from the handle to the base. From the back, the left one has either the intake or outflow for the canister and the right one has the reverse. The middle one is where the base of the extension hose and cord is mounted. On all three the plastic has cracked at about the point where the bottom of the canister meets the permafilter. The vacuum is useless now and
I'd suggest using an epoxy cement (3M makes really good stuff) The epoxy comes in 2 separate tubes or bottles. Each alone will do nothing, but when combined become incredibly strong. Use care when using since on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
The small button on the hose handle is missing, I need a replacement
... Euro-Pro EP923 Canister Steam Vacuum
Foot latch is broken. need to replace with new one. how does one access to remove the foot pedal latch. By foot latch, I mean the foot lever that releases the upright to lower the handle and begin vacuuming.
It is accessed from the bottom underneath by the rear wheel. However, If there are and cracks on the pedal release socket area then the base will need replacement. parts are little cost but the unit needs to be completely disassembled. ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum
Can you remove the plastic hose that leads to the handle as mine has split. I thought i could remove it by pushing in the two black bits of plastic then shorten the hose. so far it wont budge. Is it meant to as Dyson sell the whole thing in one? cheers john
Yeah sorry it is sold as a complete unit and its a real pain to strip down so it better and faster to just buy the whole thing from dysons website ... Dyson DC07 Bagless Upright Cyclonic Vacuum