Having problems with your Electrolux Centralux Vacuum ?

Electrolux Guardian Lux 9000 loss of power. I can measure 122 volts to the prongs where the cord is attached but do not measure that voltage at the prongs on the front of the canister where the hose connects. Is the something in the canister that controls the transfer to that plugin?


Answers :

Repair Help & Product Troubleshooting for Electrolux Centralux Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Electrolux Guardian Lux 9000 loss of power. I can measure 122 volts to the prongs where the cord is attached but do not measure that voltage at the prongs on the front of the canister where the hose connects. Is the something in the canister that controls the transfer to that plugin?


... Electrolux Centralux Vacuum

Kenmore progressive canister bad connection from hose to canister


It could be, the female part of the connector is stretched open. You can usually insert something, like a dart, between the sleeve and the holder, to tighten it. If you paid with Pay Pal, see about getting your money back. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

The repair shop told me my Oxygen3 needs to have a sumo(?) board replaced...again. I am not willing to pay for another repair and am wondering whether an new hose and adjustable extension tube would solve the recurring problem. Is the sumo board located in those parts or is it a malfunction that transfers to somewhere in the canister?


The Sumo Board, is housed inside the canister section, part # and discription below\015\012E-1180136-56 SUMO BOARD\015\012So replacing the hose and or wand will not fix the problem. Suggest you stay away from "big box", retail, discount s ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

My dc 24 dyson red ball is making a very loud noise ive been told to check all the hose but im struggling to take to front part off where the roller is it seems to be picking up as the canister has dirt in it thanks


Hi there,\015\012\015\012You should be able to resolve this issue by following these simple steps: http://www.dyson.co.uk/support/help. ... Dyson Ball DC24 Bagless Upright Vacuum

I am replacing the hose on my kenmore canister 11622612200. i easily replaced the handle end of the hose, but cannot see how to replace the end that goes into the canister. can you tell me how to disassemble the canister end for the new hose? many thanks!


Open the canister and locate the hose intack. There is a plastic retainer which slides over the end of hose and is secured to the body of the canister with a few screws. Remove the screws and pull the retaining ring up to release the hos ... Vacuums

I have an older EVO canister vacuum model 116. 22822200. This has a hose between the canister and the floor sweeper. Switches are on the hose. The hose needs replacing. Can you give me a price and part number for this hose? Can I order it at a store or on-line? Thanks, Alan.


... Kenmore EVO All Surface Floor Cleaner Vacuum

I need to replace the hose on my Euro Pro Shark canister vacuum EP722. After numerous searches, unable to find online. Looking for simular hose that will attachment to canister. What hose from another model or even maker will work? Thanks


Go to shark in GOGGLE. Go sharks wedsite, find your vaccum, click your hose. We have 3 mops and vacuum. No trouble getting parts and filters. Not high priced. ... Euro-Pro EP722 Canister Vacuum

Scunci steamcanister model 52038 Steam does not get from canister through hose to nozzle. No apparent leaks - hose does not get warm. appears may be valve problem from canister to hose. Only used bottled water - barely used this machine.


... Scunci Vacuums

Kenmore Canister Vacuum Model 116.23912300 Hose Connection Pipe (KC92PBZTZV06)


To remove the cover. There are two tabs on the connection pipe that hold the hose connector onto the connection pipe, one on each side located on the section of the connection pipe just next to where it bends. They are visible under the lip of the co ... Kenmore 25512/ 25513 Progressive Canister Vacuum

My Miele S3141 canister began acting strange this morning. No suction...so I took off the hose and checked for blockage, (nothing). Now I can't get the hose back on the canister. It just slips ar


See this causes and fix it. God bless youAir filter:If the vacuum cleaner won't pick up dirt and has no suction the air \012filter might be clogged. Remove the filter and either clean or replace \012it as needed. \012 ... Vacuums

I got this sewing machine , can anyone tell me what this control box is used for ?. It is mounted under the table in front of the motor,It says Control Box on the front and two push button number settings with can be adjusted up or down from ( 0 to 9 ) ,Next to these settings are two toggle switches. One is marked start with on and off and the other switch is marked end with on and off. Above these switches it it says Back Track . The tag on the box says ( Type LE -BB -24 - 110 - 220, 2


Still struggling with your model number. I understand from the added comment this is a Brother sewing machine. I was hoping to find a manual that would be of assistance. Here is a couple of websites that lists available manuals for Brother sewing ... Vacuums

Replacing wheel Hoover spirit vacuumm - Hoover Spirit Canister Vacuum Cleaner Non Electric Hose Canister Vac Cleaner Non Electric Hose


... Hoover Spirit Canister Vacuum Cleaner Non Electric Hose Canister Vac Cleaner Non Electric Hose

Hello, I have a Kenmore Progressive Canister Vacuum 116.20912006. It won't turn on. On the hose assembly, the end where the hose swivel is, there are 4 metal pins that plug into the canister. One of the pins looks like it broke off. There are only three pins remaining. I assume there should be four pins as there are four holes. Is this the problem and is it fixable? The vacuum is from 2002 so I am not sure a replacement part is even available and at what price. Thank you. Susan susan.eng@


Hi Susan, if the pin has broken off you can do one of two things, first, would be to find a local vacuum repair shop and take it there for them to look at. they may be able to look at the hose and fix it for you pretty cheaply. what ... Kenmore Progressive 20912 Bagged Canister Vacuum

I have a central vacuum system. When I disconnect the hose from a wall outlet the central canister does not shut down dispite my turning off the vacuum at the handle of the hose. The only way I can get the system to shut down is to pull the plug at the canister. What gives? Rob


What I'm hearing is the canister(Not the Powerhead) portion of the unit is running all the time unless you unplug it. this problem could be caused by a short in one of your low voltage lines running through the house. To determine that just unplug on ... Vacuums

Blocked suction The FLOOR suction line (Hose) is clogged. I Can vaceum the floor, but it will not pick up anything because the hose to the bagless canister is blocked. I can switch from floor to hose and can vaceum furniture. it will not pick up off the floor. I have tried running a wire down/up the hose. I Can feel the blockage, but I cannot get it out. I am afraid to pull the flem hose out as I do not know how it is attached at each end.


Hi,Here is a tip that I wrote about my Bissel ... the hose should just pull out... it is just stuck in there tightly...\015\012Bissell Bagless Upright Vacuum ... Royal 088500 Featherlite Upright Vacuum

Clogged hose A makeup brush (about 3.5 inches long) was sucked up through the vacuum hose. It won't come back through the same way it came in because the bristles in the brush are expanded. We can see the brush on the side of the hose that connects to the canister but can't get it around the bend of the 360 part of the hose... is there any way to take the hose apart more?


... Kenmore 25512/ 25513 Progressive Canister Vacuum

My electrolux 2100 vacuum hose broke. I replaced the hose but now I dop not have power at the hose end. is there a curcuit breaker in the canister tha supplies power to the hose??


... Electrolux Guardian Bagged Canister Vacuum

I cleaned out my brush in the bottom front, cleaned out the small tubing going into the canister, and the canister itself. I also changed the filter.I snapped everything back into place, but Since then, it doesn't seem to have any suction and there seems to be a space between the canister and the bottom of the vacumm where the canister sits. At that area, you can feel air coming out when trying to vacumm and it just doesn't pick up, it seems to be just blowing stuff around.


You need to really look at it some thing is out of line you shooed not have\015\012any spaces in the top or bottom\015\012pull the canister back out and look at the pins that you lined up with the\015\012to ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I am currently unsure, it my Dyson DC16 battery is charging as it should. I read all the posts about Powersupply voltage of 28V and defective PCBs. I now need to know from someone who's DC16 is working properly what voltage the battery should have when it is charged. I currently only measure 24.2V in mine. Supposing there are 6 batteries in there with nominal 3.6 voltage each, which would add up to 21.6, I supposed one could charge with up to 25.2V (4.2*6) and once reach lower the voltage ke


Does it stop working real fast ? ... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

Hoover Uh30010com the hose on the canister does not stay lock (it keeps poping out). I heard great reviews on this vacuum but I am so dispointed with the canister I am ready to return it to the store, I think it is a waste of money if you can't use the canister... I cannot believe I did not find reviews on the canister.


You can take it back. they will return it they know this happens all the time. If you like canistar vacs you should get a tristar. they are the best! call me for more info 866-635-9254 John ... Hoover Vacuums

Where do I find a replacement for the hose that attaches to a Shark EP 3005 canister? The hose I have to the vacuum split.


Have you tried here > http://www.sharkclean.com/cgi-bin/livew/ ... Euro-Pro EP3005 Bagged Canister Vacuum

I have an old Miele canister vacuum and I do not know how to disassemble the hose to check for a clog. I think it sucked up a nerf ball the size of a ping pong ball. I changed the bag but it did isn't appear to be in the bag. The vacuum powers on but I do not have suction with the hose, and since the hose has hard plastic elbow joints I do not want to pry them apart and break it


Hi Emily: If you have the model number for your machine you may be able to find your manual on the Miele website. Check ... Miele Vacuums

I have a dyson dc21. All the sudden the hose is hardly suctioning up anything. If I take the canaster off, the top air hole suctions extrememly well, but when I place that canister back on, the suction is not going thru the hose and picking anything up. I have squeezed the hose, I feel no air leaking and do not feel any blockages...what could be wrong. It worked fine the other day and today, it won't pick up a piece of lint!


... Dyson DC21 All Floors Stowaway HEPA Bagless Canister Vacuum - Iron/Titanium/Yellow

I bought a house that has a 1970s GE microwave oven that's built-in above a traditional oven. (Unfortunately, I can't locate a model number for the microwave.) I'd appreciate having information about the "food temp control," which is on the front of the oven. There is a wire probe that goes from the inside of the microwave to the food. I assume that relates to the "food temp control." I'd appreciate having any information about how to use the "food temp control." Also, I 'd like to know wh


I serious doubt that probe would work any longer for they go out in ten tears or less ... Vacuums

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each


Should be a pry off dot on the underside revealing a screw ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0717 seconds