Having problems with your Electrolux EL4100A Ergospace Cannister Vacuum ?

Turbo brush won't roll - Electrolux EL4100A Ergospace Cannister Vacuum

Answers :

Repair Help & Product Troubleshooting for Electrolux EL4100A Ergospace Cannister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Turbo brush won't roll - Electrolux EL4100A Ergospace Cannister Vacuum

... Electrolux EL4100A Ergospace Cannister Vacuum

Hidden screws ergospace - Electrolux Ergospace Cannister Vacuum

... Electrolux Ergospace Cannister Vacuum

Electrolux vacuum brush not turning problem: was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won't even switch on. Hope you can help

Under the vacuum, there is a guard.\012remove the guard , either by 2 screws or by 2 clips.\012there is a belt under the guard.\012that is connected to the brush.\012the belt need to be replaced. ... Vacuums

Brush roll belt stops turning when in position to vacuum. Does turn when vacuum is turned onto side. Belt is in tact, brush roll is fine. What's going on?

I think I know what the problem is with your machine. It's a rather lengthy repair, and I'll be happy to photograph it for you (like I do on most of my Fixya answers), but I'd like to know before doing all of that if you still need help, or if you' ... Eureka Smartvac 4870 Bagged Upright Vacuum

Brush rolls of my Euro-Pro Shark vacuum (model-UV 210CN) are stuck; the brush is unable to roll. Does that mean I have to the roll on one end or the whole brush unit? I live in Canada and if possible let me know where I can find a store. Thank you.

... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula

There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge

... Vacuums

I have an electrolux genesis upright vacuum that I bought used about 8 years ago. It has been A great vacuum the best I ever had. I thought the belt had come off so I took it in for repair. They called today and said that the brush rotor motor was bad and it would be around 148.00 dollars to repair. My question is could I buy the part and have my husband replace it or would it be too complicated. Can you still buy an electrolux vacuum comparable to this one and how much are they. I love this vac

... Vacuums

I have a Bissell Lift-off Revolution Turbo vacuum and the brush doesn't spin on its own anymore. Does this mean the motor is busted because there's no noise when you press the brush button. We've just replaced the belt, hepa filter and a new brush. But its still the same. What's wrong with my vacuum?

Its probably the motor. remove the covers with a #2 phillips head screwdriver and cut the wires to the motor ( unplugged ). purchase some crimps at radio shack to resplice the wires together in the same fashion. ... Bissell Vacuums

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,

It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

I have the bissell powerglide vacuum with the turbo brush attachment. Being the neighborhood "cat lady", I love this attachment -- that is, I did until it just stopped spinning. I don't see anything blocking the brush. It just doesn't spin when I attach it to the vacuum hose.

1. this could be (2) things that are happening or 32. there is hair surround the spindle (rotation) brush tool blocking rotation or you have a motor that has failed and it is not turning the rotation brush.3. the switch (on /off) has fail ... Vacuums

Brush roll won't turn on for the shark NV22L vacuum. the light on the brush roll is dark, not red or green

Atthe bottom of the vacuuam are screws to take off...two of them are near the rear wheel assembly....two of them are behind the front mini wheels (just pry the front mini wheels so that they pop out...they pop back in)Remove all of the screws. Re ... Shark Helmet NV22L Shark Navigator Upright Bagless Vacuum

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks

If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

We have the Bissell Lift off Revolution vacuum. The brush roll and belt are broken. The brush roll has seized up and no longer spins which caused the belt to burn out. How much is a replacement part cost? Debie [email protected]

You can get the belts for that model here: http://vacbelts.xps.convina.com/bissell-style-8-belt.htmThey are only 4.99 for a 2 pack. Plus they ... Vacuums

Brush roll i am trying to find and purchase a new brush roll for my ge vacuum. The number on it says that it is 106585 and from what I can tell that is the same as 5550 parts. Is that correct?Thank you

I have the same vacuum for the last 5 years.  I dont know if its the same as 5550 (I assume it isn't) but I can give you the part number 61445-1.  It costs around $16 and you can call 1-877-207-0923 b/w 7 am and 8 pm Mon-Fri central time, o ... GE 106585 Upright Vacuum

I live in Mexico and have a Electrolux Easy Box Vacuum...I am looking for a hard floor brush that will fit the hose as my old Sears brushes are a little too small.This model is bagless and may only be sold here,but I do not care for the floor/rug brush combo brush as it does not clean tile floors very well.I would order and have a friend in the states bring to me.Thank you,Linda Staton Cozumel Mexico

... Electrolux Vacuums

The beater brush on my vacuum appears to roll when I turn on the vacuum however, you only hear the actual sound of it on occasion and the vacuum is not vacuuming thread off the floor.

Greetings from GoVacuum,\015\012\015\012Your belt has probably been stretched to a point, the brush no longer spins when it touches the carpet. You probably can turn the machine over, and see the brush spinning, but it's probably stretch ... Eureka Vacuums

The brush roll does not turn or turns very slowly in my Electrolux model EL6986 A

... Electrolux UltraSilencer Vacuum Cleaner (formerly the Harmony) Fast Free S

Miele vacuum turbo plus brush does not rotate

Hi Jeanakemi10,The front brush motor will not engage until the power is turned on and\015\012the handle is in the down position. In the upright position the brush\015\012motor wont engage. Typical faults will be the belt is broken and nee ... Miele S318 Bagged Canister Vacuum

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!

Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

My Electrolux Regency Series upright vacuum brush motor does not activate. Cleaned the brush and press reset to no avail. Opened handle switch assembly and checked each wire attached to all three switch settings. Tried disassembling brush assembly but could not pry open after removing all screws.

... Electrolux Vacuums

My electrolux oxygen canister cuts on and off. I have to open and close the vacuum, or take the base of the hose off and then re-insert. I have to do all these things before it will start up again. I sometimes shake the hose around, then it will come back on. If I try to dust with the dust brush (like a lamp shade or shelf) and the suction pulls against the object, the vacuum goes off for awhile. Sometimes I'll have to reset the vacuum by unplugging the electric cord. I never get to finis

Maybe you should have taken it back to that shop, it appartently isn't fixed. I would have replace that board, don't believe in modifing, you usually end up with other problems, like you have. One thing to check is maybe you have a partial clog in ... Vacuums

I have a canister style vacuum. The brush roll has stopped rolling on carpet. When turned over, it rolls fine. I have disassembled and cleaned out hair and that didn't work. Any help would be very much appreciated. Thank you. Martha

You need a new belt. They stretch after awhile and won't turn the brush roll under load. ... Vacuums

Bissell Vacuum brush stopped rolling

The belt may be broken. Consult the user manual or locate on the sole plate or front hood when getting to the sole plate. Usually it involves a few cross head screws on the base of the vacuum cleaner where the roller beater bar is. Remove that and ch ... Eureka 2961AVZ Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1242 seconds