Having problems with your Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum ?

Oxygen 3 will not turn on

\015 I was vacuuming and my electrolux oxygen 3 just shut off. I cleaned out hoses and replaced bag. I waited 30 minutes, but nothing happens when I plug it in. No lights come on or anything.\015

Answers :

This is often caused by a failure of a fuse on the Sumo board, or occasionally by a failure of the cord reel. I just posted a rather extensive set of instructions on how to check these things as a response to a different thread, but I will repost them here:
\015\012
\015\012--
\015\012There is a board in the back (called the "SUMO board") which has a fuse hardwired to it. Most of the "no go" problems with this machine are related to this.

In order to check it, you'll want to take a thin flat-head screwdriver, and gently pry up the silver panel on the top of the machine. The easiest place to do this is on the side of the panel, as far toward the rear of the machine as possible.

You will then need to remove the 2 Torx screws on the rear panel, and the top body of the machine should then be able to be removed. There are two clips in the bag chamber, directly under the back portion of the bag compartment lid, which can be pressed in to facilitate removal of the back cover.

The sumo board will be sitting directly on the top of the machine, and the fuse in question will be on the right if you are looking at it from the rear of the machine. Unfortunately, if the fuse is blown, you will have to replace the entire circuit board. (Unless you feel very comfortable with soldering a new fuse onto it, which I do not recommend for safety reasons.)

You can also check continuity of the cord reel from here. On the right hand side of the board are two spade terminals leading to wires running down into the cord reel assembly. One black, one white. Checking the continuity between these terminals and the ends of the power supply cord will allow you to determine if the cord reel is providing power to the machine.

Accessing the cord reel will require you to remove the six Torx screws holding the main body to the base. Two of these are on the rear of the machine, and are very deep inside; so you will require a very long-shanked Torx driver to get at these. Two more are inside the bag chamber at the rear, and the other two are on the front handle assembly. This will allow you to lift the main body away from the base, and if you are replacing the cord reel you can pull the wires from the spade terminals and the socket on the sumo board, and feed them back down into the cord reel chamber to remove the old cord reel.

Reassembly is simply a reverse of the previous. Beware, however: getting the cord reel to align is something of a chore, so make sure that you have the retraction system functioning before you put the whole thing back together, or you'll be bummed when you finish reassembly and the cord won't retract.
(I've definitely never done that. Nope. Never.)

Hope that helps, good luck.

-R
Attention rebranded Electrolux Owner
\015\012If you live in the Oklahoma City area I still sell the the original Electrolux. It is now called Aerus Electrolux. We do work on the the orange thing. But why keep something that don't work.
\015\012Trade it in.
\015\012Aerus Electrolux
\015\0122409 N Council Rd A
\015\012Bethany/ Oklahoma City
\015\012405-787-3272
Repair Help & Product Troubleshooting for Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My electrolux oxygen vacuum cleaner shut off and will not turn back on. It's less than a year old, but I bought it off Craig's list--they were the orginal owner and they said they bought it in May of 2008. I've only used it a few times and it worked fine except for the last time when it suddenly just shut off. I thought maybe it had come unplugged and I didn't really worry about it because I was finished vacuuming. But, I went to use it tonight and it would not turn on at all--no lights, nothing


No..Electrolux is really great about warranty service. They will help you even though you are not the original owner. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Power brush not turning on electrolux oxygen. AC


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Oxygen 3 will not turn on


This is often caused by a failure of a fuse on the Sumo board, or occasionally by a failure of the cord reel. I just posted a rather extensive set of instructions on how to check these things as a response to a different thread, but I will repost the ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

My Electrolux Oxygen vaccum el6988 will not turn on.


... Vacuums

Electrolux oxygen 3 troubleshooting will not turn on. No lights...NOTHING happens when I push on/off button


Maybe it is the p.c.b or a fuse shuold take to a dealer ... Vacuums

Hi: I have a 14 month old EL7024 Oxygen that has no power. Will not turn on. No power at lights that are usually flashing. Wall receptical has power. Does not seem to be a thermal reset, full bag or plugged filter. Owners manual is no help. DAve


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

BUTTONS TO TURN ON ELECTROLUX EL7020B OXYGEN CANISTER VACUUM


I need a picture of how to insert an Electrolux oxygen 3 bag ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

I have an electrolux oxygen canister that's 4 yrs old and it just stop working. It just doesn't turn on and no lights display. I veryfied that the outlet works. I took it at my local Eletrolux store but they don't deal with this model. They told me that this model is made in Europe and they don't support it. Where can I take it to be looked at or do you have any ideas what the problem might be. Last time I used it it was working fine. Thanks, Rodi


... Electrolux Oxygen Z5540 Pet Lover Vacuum

My vacuum cleaner will run for a few minutes and then shuts off. The plug light on the panel blinks. I thought the motor was shut, but after a long time it will turn on again, but again, only for a few minutes and then shuts off again. Any ideas? I bought an Oxygen Ultra a few years ago, but I don't like it nearly as much as the old Epic.


I know nothing about your particular vacuum, but many vacuum cleaners these days have\015\012safety cut out's, which causes the motor to do exactly what you describe. Sadly blockages, faulty switches, over stretched cables, carbon brushes etc c ... Electrolux Epic 6500 Vacuum

My electrolux oxygen won't turn on. Could it be the switch and can I fix it myself?


Mcdevito75 here, The first thing is to make sure you are useing a live or good wall outlet. Then you can try the on / off switch a few times. If this doesn"t work it may be the switch itself. Look for an appliance repair center in your area. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Electrolux Oxygen 3 Model EL7020 with a bag and HEPA. I have a body only,and problem is-I can't turn it on.I read in a Manual,it possible only when electric hose connected to the body, . so I have to buy a hose, what is relatively expensive. Does anybody knows,how to check this vac without a hose? Thanks.


\015\012You can get a replacement hose here http://evacuum ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum

3 year old Electrolux Oxygen 3 will not turn on.


I had a situation where the main unit turned on and kept flashing its lights but I was unable to start it by pressing the buttons on the hose.Turned out, the switch assembly in the handle was waterlogged. It is a two-wire resistance switch, so it ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

I have an Electrolux Oxygen 3 Ultra Canister Model No Rel7020. I am having problems with the On/Off Button and the Bare floor/Carpet Brushroll On/off button. The Carpet On/Off will not work at all. In order to turn the vacuum on, I must press a combination of the first two buttons. Is this an electrical issue


You have a problem with the electrical switches. If you are comfortable with this, take apart and double check internal wiring to make sure nothing was frayed, or disconnected. Make sure it is unplugged. If you know how to operate a multimeter, yo ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Electrolux Oxygen 3 model 7020A contols not working


You need to replace the hose itself. The buttons in the handle a very cheap and go bad all the time. ... Vacuums

Auto rewind for the electrolux oxygen 3 ultra


The Electrolux Oxygen 3 is a piece of ****. I was dupped into buying because Consumer Reports said it is a high quality product. Wonder how much they paid for that endorsement! I the brush roller design is flawed and clogs all the time and then will ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.


... Hoover Tempo Widepath Upright Vacuum - Blue

The brushes on the Hoover All Terrain Steamvac won't turn. However, when I try to turn them manually they will turn. So, why won't they turn when the machine is turned on?


Some vaccums have a belt on the brushes. might need a new one if it does have the belt ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th


... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

I have an electrolux Enviro multi steamer which I was using this morning. I turned the steamer off for approximately 1 1/2 to do some shopping, and when I turned it on again, the steamer light turned on (green light) and then I waited for the orange light to go on, which too a while. When the orange light does turn on, there is no steam when you press the yellow button on the handle. I have checked for water, and the steamer is full, I have turned it on and off several times just in case that wi


Problem fixed itself. Turned off for couple of hours so unit can cool down completely and when I turned it back on it started working again. ... Vacuums

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos


It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

I saw your response to the Tork 1101 timer posting. Could you make a guess on my problem? It runs fine for turning on and turning off the downrange lights. But when it turns off the downrange lights the timer itself turns off. The clock stops.


... Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

I have a dyson canniter stow away vacuum. i've had it for 2 years and it just started having a problem. when i turn it on the motor starts just fine but the vacuum head does not turn on. Yet when i push it forward it trys to start and turns on for a second and turn off - almost like the connector isn't connecting the hose to the head very well anymore.


Hi, After reading you're problem, the symptom's are just like you said. Its just a matter of checking the connections. The connection where it plugs into the head it self. When you push forward the forward motion and down pressure makes ... Dyson "Stowaway" Canister Vacuum Vacuum

My Dyson DC07 will not turn on. I was just using it and moved to a new area and plugged it in and it turned on for a split second and then it turned off and now it won't turn on at all. Any suggestions?


Loose wire, bad switch, or thermal cut-out. In any event, you will have to use a voltmeter to troubleshoot the problem, there is no way of knowing the problem otherwise ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won't turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can't get it to budge. This is exactly what is keep brush roller from turning.


Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn. ... Kenmore 25512/ 25513 Progressive Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0456 seconds