Having problems with your Electrolux Epic 3500 Vacuum ?

I would like to know how i get the very bottom piece off my vacuum off so I can put a new fidder hose on it? The hose is black and it is only about six inches long. its lacation is on the very end of the vacuum but between the end and the piece that gos along on the floor.

Answers :

You don't have to take the vacuum apart.
\015\012Assuming this is an Epic 3500 or similar upright Electrolux:
\015\0121. Lay vacuum on it's side.
\015\0122. Gently pull hose from power head. It's not screwed in so that should be easy.
\015\0123. Unscrew it from the upper portion of the machine by turning the hose clockwise. Turning counterclockwise tightens it.
\015\0124. Remove it.
\015\0125. Screw one end into upper portion of vacuum by turning counterclockwise.
\015\0126. Insert other end of hose into opening in power nozzle. Some manipulating may be necessary for proper fit, but this is all that's needed.
Repair Help & Product Troubleshooting for Electrolux Epic 3500 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I would like to know how i get the very bottom piece off my vacuum off so I can put a new fidder hose on it? The hose is black and it is only about six inches long. its lacation is on the very end of the vacuum but between the end and the piece that gos along on the floor.

You don't have to take the vacuum apart.\015\012Assuming this is an Epic 3500 or similar upright Electrolux:\015\0121. Lay vacuum on it's side.\015\0122. Gently pull hose from power head. It's not screwed in so that should be eas ... Electrolux Epic 3500 Vacuum

I have designed a machine for cleaning and harvesting using a centrifugal fan. The flexible hose is 203mm Diameter and 5 metres long. How can I calculate the vacuum pressure this machine creates at the end of the hose? I would like to use this information in the advertising and to compare with other similar machines. Thank you Alan Churchill [email protected]

See this can help youhttp://www.npl.co.uk/server.php?show=ConWebDoc.1377Sergio ... Vacuums

How can i put on the snap ring on an eloctolux vacuum hose on the end piece of the hose; it is a swivel end and an older vacuum cleaner plastic canister type

The snap ring is generally found on a Canadian made LUX AP series prior to 1982 and it is in fact a coil spring you must leave the wiring off the handle. Be sure the steel cap and rubber o ring are on the tip of the hose. Slide the handle onto the ho ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I have a Hoover windtunnel T series. Model #UH70105. The system check indicator was almost red so I cleaned the filter. There are no clogs and it vacuums fine without the hose, but when I go to use the hose there is very little suction and all the vacuum dust flys out of the end the hose piece fits into when not in use. Can you please tell me what is wrong?

... Hoover Vacuums

I have Optima, 12amp Eureka vacuum, Model 431, AXZ type and the extension hose for cleaning corners and edges --the plastic part that the attachments fit into has a piece broken off and tools don;t fit anymore. It looks like the hose attachment can be replaced--can it be and if so--where can I get a new hose attachment. It seems it is cheaply made of plastic and really shouldn't have broken a piece off.

... Eureka 431A Optima Bagless Upright Vacuum

Hello, I have a Kenmore Progressive Canister Vacuum 116.20912006. It won't turn on. On the hose assembly, the end where the hose swivel is, there are 4 metal pins that plug into the canister. One of the pins looks like it broke off. There are only three pins remaining. I assume there should be four pins as there are four holes. Is this the problem and is it fixable? The vacuum is from 2002 so I am not sure a replacement part is even available and at what price. Thank you. Susan susan.eng@

Hi Susan, if the pin has broken off you can do one of two things, first, would be to find a local vacuum repair shop and take it there for them to look at. they may be able to look at the hose and fix it for you pretty cheaply. what ... Kenmore Progressive 20912 Bagged Canister Vacuum

The belt on my used Eureka Boss 5857 upright slips off the end of the motor shaft every time the vacuum is used. When I turn the brush roll slowly by hand, the belt walks toward the end of the shaft. It looks like there was a plastic projection from the base that snapped off, and maybe that plastic piece used to block the belt from falling off. Do I need to try to reconstruct that plastic piece, or is something else wrong?

... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

Kenmoore Intellivac w direct drive suddenly started making internal sound like something was stuck. Hose is clear, and sound is made when hose is detached from main unit. Vacuum sounds find at lower pressure, only makes sound with bag door closed and/or placing my hand over the end of hose.

Shut off the vac and open container and remove the bag. Try dropping a coin into the hose, then raise up to see if it falls thru to the bag area. If it does check the throat of the vac where the dirt is sucked upward to dump into the bag itself. ... Kenmore 35912 / 35913 Progressive Upright Vacuum

I have a cannister (Animal something...) Today, it didn't sound right - like a blockage. I took out the filter - seemed OK; I looked for a blockage - found none. I continued to vacuum, but it wasn't picking up. Then, I stopped again, and I found a blockage (cat toy mouse) right at the end of the hose (attachment end.) I cleared, and I turned back on - nothing. Completely dead. It is one year old, just about exactly. Desperate, Sharon Tracy

Hello,if your canister is completely dead, then it means its having a power problem. You need to focus your attention on that part of your canister that relates to power. Such as; power wire, if you don see any fault with the power cord, ... Dyson Vacuums

The latch on the hose (at the canister end) of my electrolux Guardian vacuum has broken. Do you know where I can buy this part. I found many places that are selling the entire hose, but all I need is the latch piece.

Find an Aerus dealer. You can go to aerusonline.com and use the dealer locater and find the closest store. Good Luck!! ... Electrolux UltraLux 2000 Bagged Canister Vacuum

My Dyson DC25 animal is having issues. I believe everything is working correctly except I have realized that the mechanism which switches the hose/valve between the wand and the vacuum head isn't working properly. The two gear pieces that move the hose placement aren't close enough together, so they don't work together. It looks like there is a washer that I could potentially remove on the clear gear piece which would allow it to sit closer to the assembly. Would that work? Currently I am

... Vacuums

Cannister model#11627915701. connector terminals in extensionwand ,and wlre harness in hose handle get hot,,,look a bit singed.. can order and do ourselves. but would like a "tune up " ,cleaning of vacuum as well. purchased in 2008. have long haired dog,,,can't afford to be without it for very long. have sears store in clay ,ny. lady I spoke w/ says it would get sent out and take at least 2 weeks.!

... Kenmore Vacuums

Hose came off end piece where it goes into machine on Vax U89-MA-T vacuum cleaner

... Vacuums

I need to change out the short hose on the underside of my older Dyson DC 07 Animal (Light Purple). It is the one less than a foot long on the underside which is attached on one end to the main body of the vacuum(I was able to remove this one) and the top of the upper soleplate. The latter one seems to be glued or otherwise permanently attached.Any assistance you could give me on this would be greatly appreciated....Thanks

Hello Cynthia,\015\012\015\012It's not glued, but it can be a little difficult to remove. You need to twist and pull at the same time and it should pull off. If it's being stubborn, squirt a little bit of WD40 / penetrating fluid where th ... Vacuums

My 8 yr old kenmore vacuum works well - however the hose has worn under the handle where there is a hole (resulting in decreased suction power). I'd like instructions on opening the handle and bypassing the worn piece of tubing rather than replacing it for $129. Some of the handle screws remove easily but the last one doesn't loosen easily.

Hi,Have you tried spraying the stubborn screw with WD40 and let it soaked for a while? Other than these screws holding the handle together, there would no other way of opening it up. Hope this be of initial help/idea. ... Kenmore Vacuums

I have an Electrolux Epic 6500 SR vacuum and the hose end with the handle is separating. Power nozzle losing contact intermittently. Is this piece replaceable or repairable?

It is replaceable. Just take it to the nearest Aerus Electrolux store and the service tech will take care of it for you.\015\012Go to the following site and follow instructions to find the stores nearest you. ... Electrolux Epic 6500 Vacuum

I have an Air Track plus vacuum cleaner and something has got stuck between the flexible part of the hose and the solid black section at the end. I tried to put a coin down to clear it but that has got stuck too. It looks like the rigid section should come apart (a small notch each side) but I can't figure how to do this.

... Samsung Vacuums

Bissell 37604 Bagless Upright Vacuum. Hose keeps clogging every time I vacuum. Is there a way to prevent this? I am ready to buy a new vacuum, but it does do a great job picking up hair...until it clogs. It clogs at top of hose. Could the hose be kinked? It does not look like it.

That is a defect in the design of that style of vacuum. I went back to my old vac because I got so tired of having to unstop it. The sharp turns in the hose and the molded plastic causes it. Find one without the turns. ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

Can I glue swivel on end of hose kenmore vacuum 116

... Kenmore 23313 Whispertone Bagged Canister Vacuum

Hose is there a repair manual for the hose on this kind of vacuum?? it got clogged pretty good and I thought by taking the hose apart there was a place to take the hose out.... I thought wrong and now I have a hundred piece everywhere and no vacuum..

... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being

Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums

I have some sort of object in the hose of my Epic 6500. I have tried reversing the hose and blowing out the foreighn piece of debeis but this has not worked. Is there a way to remove the plastic connector end to access this end of the hose? Or is there another solution to this problem?

By reversing it, I assume you plugged the hose into the exhaust blower on the top of the machine. If so, insert the other end into the intake and turn one the vacuum. This way the clog is also getting sucked at what should be the loose end.\0 ... Electrolux Epic 6500 Vacuum

My electrolux oxygen canister cuts on and off. I have to open and close the vacuum, or take the base of the hose off and then re-insert. I have to do all these things before it will start up again. I sometimes shake the hose around, then it will come back on. If I try to dust with the dust brush (like a lamp shade or shelf) and the suction pulls against the object, the vacuum goes off for awhile. Sometimes I'll have to reset the vacuum by unplugging the electric cord. I never get to finis

Maybe you should have taken it back to that shop, it appartently isn't fixed. I would have replace that board, don't believe in modifing, you usually end up with other problems, like you have. One thing to check is maybe you have a partial clog in ... Vacuums

I have an electrolux central vacuum in my house. My central vac hose has something stuck in it, I think, maybe a sock. I tried to put a long dryer wand down it but the hose is just too long. Does this need a repair man or new hose?? Any idea of a way to blow it out? Thanks.

The best way to clear an obstruction is to blow it out by attaching the wall end to the exhaust of a shop vacuum, or using an air compressor.\015\012You can try holding the wand end of the hose directly to the CV in port and turning the machine ... Electrolux Central Vacuum

I just bought the LG200R vacuum. It is working wonderfully but i have only had it a week. I have already had to clean the agitator but this is due to my extremely long hair and apparently i shed a lot. I was wondering if i should be alarmed by the funny smell it leaves in the air. Its not like a burning rubber smell but more like a fresh plastic smell or sorta chemical like smell (hard to describe) and it doesn't need to be on to make this smell it seems to be permeating off the vacuum itself

... LG LUV200R Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1137 seconds