Having problems with your Electrolux Epic 3500 Vacuum ?

I have an Electrolux Epci 3500 Sr upright vacuum cleaner ... 100 percent positive switch is shot and one of the wires inside is fried but before buying a new handle assembly online how do I check the motor to make sure it's not fried?

Answers :

The switch is replaceable, so you don't need to replace the complete handle assembly. I've got a 3500 that I replaced the switch on and it works great now. You can get a new switch at the local Aerus Electrolux store. To find the nearest store, just follow the directions on the below site.
\015\012I do recommend letting the service tech do the replacement.
Repair Help & Product Troubleshooting for Electrolux Epic 3500 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have an Electrolux Epci 3500 Sr upright vacuum cleaner ... 100 percent positive switch is shot and one of the wires inside is fried but before buying a new handle assembly online how do I check the motor to make sure it's not fried?

The switch is replaceable, so you don't need to replace the complete handle assembly. I've got a 3500 that I replaced the switch on and it works great now. You can get a new switch at the local Aerus Electrolux store. To find the nearest store, ju ... Electrolux Epic 3500 Vacuum

My Electrolux Regency Series upright vacuum brush motor does not activate. Cleaned the brush and press reset to no avail. Opened handle switch assembly and checked each wire attached to all three switch settings. Tried disassembling brush assembly but could not pry open after removing all screws.

... Electrolux Vacuums

Brand new LG LUV200r used 10 minutes now after removing dust tank & reinstalling the vacuum motor does not run only the beater bar??? I have located wo circuit breakers both seam to be set. This suction motor should run when the switch is pressed & the beater bar should operate when the handle is moved down??? Not A happy customer will return unit to Best Buy only 100 mile round trip!!!! RDH

... LG Electronics Kompressor Pet Care Upright Vacuum Cleaner LUV200R

My vac has lost suction. When I vacuum it picks up very little, but when I remove the wand hose it has good suction. We have cleaned both filters, checked for blockage in all hoses & cleaned the beater bar brush. All to no avail. Is it the motor? Or is there a blockage deep in the vac somewhere? We're debating repair versus buying a new one. Hope you can help. Thanks.

Hi there,Sorry to hear you're having a problem with your DC14. Since you say you've already washed the filters and checked for blockages, it's probably best if you get in touch with us so we can run through some simple troubleshooting ste ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?

... Vacuums

MRG 720-42/2 Hi, I have a vacuum Miele and the motor failed....and now I would like to buy a new one. The motor type is MRG 720-42/2 If you know where could I buy it, please let me know...... Many thanks is advance. Carlos Suarez [email protected]

... Vacuums

I have 16981 Model. The trigger assenbly has snapped off the retaining pieces inside the handel. Can you buy a new handle with the trigger assenbly? What is price and part number? Also the lever to adjust the up and down movement of entire handle has broken. Can you buy? Is it possible to fix it and price for part?

The best place to obtain a replacement part for your unit is to either try and download an exploded view of the product, found in a service manual (which is often information restricted to the authorised repair agent), to get to the part number. ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.

It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums

I have lost the cap that locks the brush in the motorized head. I didn't realize it was gone until I went to use it. Can I purchase the locking cap or can I buy a new motorized head for it. I lov

If this part is for a Dyson vacuum here is the link:http://www.dyson.com/parts.aspx?gclid=CJShrcD99rQCFYKK4AodBDwA7g ... Dyson DC35 Handheld Vacuum

Where can i buy a new stabilizer assembly for a dyson dc18 slim? The shiny plastic frame piece of the assembly above where the hose attaches is cracked through. I called Dyson and they won't ship that part in particular. Any ideas?

... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

Hoover Upright U8185-900 agitator brush stopped working...took hood off...PCB display bridge fried...ordered new one & installed...that burned up in 15 seconds...ordered another PCB and new agitator motor...and since I was in there every **** thing else replaced also...took whole thing apart and cleanded even tho agitator brush was not jammed...put all back together...**** thing just sits there with red led lights displayed...this is ridiculous

... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i

At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

Handle broke and had to call in the duct tape. hate to trash the vac just for this reason (although i'd take almost any excuse to buy an oreck). is there any way to get a new "ergonomic handle"??? thanks

This site will probably help you:http://www.fixya.com/websearch.aspx?cx=partner-pub-8183356113384228%3A3nccpq-il5y&ie=UTF-8&cof=FORID%3A11&q=ergonomic+vacuum+handle&sa=Search#1392Jim ... Euro-Pro NV31 Infinity Vacuum

Dyson My Dyson DC04 runs for a second or two then stops. I have checked the motor. The brushes are good but the commutator is a slightly pitted.Do I need a new motor?

Hi.\015\012\015\012Check mains lead where it enters machine very common for internal fracture.\015\012\015\012To prove this try waggling lead with machine switched on if it starts & stops this is the fault.\015\012 ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

My bissel pro heat cleane's brushes stoped. I checked the belts. They are okay. There is no sign of heat or problems around the motor. Is there a mercury switch some where in the handle so the brushes only turn when the handle is lowered?

Depending on which model you have, you did not say, if the cogged belt goes to the pump pulley, the cogs may be wore away or and won't turn the brush roll. On some other moels, there is a brush roll motor that may have gone bad. ... Vacuums

Replacing a belt on the Riccar 8850...I see how the brush assembly will work with the new belt. But I don't see how a new belt will turn on the small rod extending from the motor. Is there a pully missing?

There is not a pulley missing, when the belt is tight the shaft will turn the belt but when the belt loses elasticity it will slip on the shaft when being used on the carpet. Replace the n\012belt at least once or twice per year. ... Riccar 8850 Vacuum

From reading comments i think my motor has burnt out (nasty smell then wont work at all) where can I buy a new motor (on line preferable) in the UAE - Dubai or UK - going home this week? thanks

Hi there you can get a motor from dysondoctor.net he is in the UK but will post anywhere in the world really ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Hi On a Hoover convertable model U4497-900 I'm trying to replace the fan. The old fan cracked, then flew apart. I have the new fan, have the motor assembly removed, but can't seem to get the pulley nut off the motor to replace the fan. Is there a trick to this or should I just try to muscle it? Thanks.

... Vacuums

It just stopped working - without any smoke or weird smell. It does not look like motor but I do not know - Is it worth fixing it or buy something new. If I could I would buy the same one but they do not manufacture it anymore

If the motor get over heated it will just switch off on you, let it cool down and try it again later,,,\015\012there is also a thermal fuse inside the motor if this has poped on you then its a bust bin job im sorry to say,, there is realy not a ... Black & Decker HV7010 DirtBuster Handheld Vacuum

I have a new bag in, checked the hoses for clogs have the motor cover off showing motor runs. Problem is vacuum has no suction in hose area, cover off where bag is and the air blows out of filter. hoses are clean no blockage.

Have you checked the filter? Many vacuums have a filter under or behind the bag to keep dust and dirt out of the motor. If this gets clogged the motor can't get any suction. Also look for holes in the hose or in the small segment between hose and bag ... Vacuums

We own a dirt devil model 088600, and are experiencing a problem with the belt wearing away a section between where the belt connects to the brushes and the motor. There is a lot of plastic/rubber residue coming out from the vacuum. We have tried new belts only to find the same problem occurs. I noticed that the source of the dust is coming from the section between the brushes and motor, where there appears to be a section that is misshapen and melted. I looked up the schematic online and can't

If you are certain that the belt is seated correctly and the beater bar is nested in its holder and the cover of the assembly has been properly installed and you still see a contact area between the belt and cover, you should either: return the vac ... Dirt Devil Vacuums

My Hoover duros s3590 just stopped running. The motor started up and then just powered down and won't start back up. Is this a faulty on/off switch or a motor problem. I'm weighing the +/- to fix or buy a new vac. TIA

... Maytag Hoover Duros S3590 Vacuum (Canister)

My Hoover carpet cleaner is approx. 7 yrs. old....husband believes motor is shot? Smells burnt when running....fix or buy new???

You are correct, the motor is shot. if you like the machine replace the motor. i would get an est. on the machine from your local vac shop and the go price them. in some cases its better just to get another machine. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Suction I too have the same problem as Mr. Chief. I followed your advice and checked all the hose attachments, no clog. Tthe only one hose that the broom handle would not pass through was the plastic hose and there is a curve in that part. I did not want to force the broom in there as this is a new vacuum and is probably under warranty.

If you have a plumbers snake you can use that. But being under warranty, I would take it to Sears for repair. ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!

Great. ... Kenmore Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 1.4114 seconds