Having problems with your Electrolux Epic 3500 Vacuum ?



Answers :

Repair Help & Product Troubleshooting for Electrolux Epic 3500 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi, i was able to get to my electrolux epic series 6500 motor. i know that my bearing is broken inside the motor but i am not able to remove the metal plates around the fans. how can i do so? thanls

You don't. This motor is not designed to come apart, not even by Electrolux service techs. The whole motor has got to be replaced. ... Electrolux Epic 6500 Vacuum


... Electrolux Epic 3500 Vacuum

Electrolux model 1521 how to remove motor Steps to remove motor please

Open canister compartment, remove rubber side bumpers, then pry off back of cylinder with large screwdriver. The plastic side parts hold cylinder together, at back, pry part over holding tab, then tap side part around tab. Part should slide out ... Electrolux Vacuums

My electrolux epic 6500sr vacuum has a seized motor. How do I acess the motor to service or change it? There are no obvious screws or clips to open the motor outer case

... Vacuums

Removing D720 electrolux motor from machine body

... Vacuums

Removing D720 electrolux motor for replacement

... Vacuums

Removing motor from electrolux vacuum D725 - Electrolux Vacuums

When viewing from the rear there are small protrusions at 2 & 4 o'clock on one side and 8 & 10 o'clock on the other side of the motor suspension bracket. These are hooked behind an internal ridge in the barrel. On one side the barrel mu ... Electrolux Vacuums

I have a Electrolux cannister Type Epic 6500 SR vacuum cleaner. The motor is making a whining noise on shutdown. What is the trick to opening it to get to the motor? THANKS, John

Hi there,the best thing you can do, is to disassemble the casing of the unit, ... Electrolux Vacuums

Replace vacuum motor on a Electrolux Epic 6500 sr

... Electrolux Epic 6500 Vacuum

Electrolux Epic 6500 Powerhead Motor

Could be the connections inside the swivel just above the powerhead. They slide on and could come off if the powerhead is abused in some odd way... ... Electrolux Epic 6500 Vacuum

Can't remove motor cover for electrolux EL2050

Usually there are screws on the bottom, normally 6-12 screws. Once they are out, there may tabs on the outside of the base fram, lightly use two flat head screw drivers and pull the cover away from the base.. be gentle as this plastic is thin, ... Electrolux Vacuums

Electrolux 1572E (Discovery II) How to remove suction motor cover?

Remove the handle assembly by taking the big screw out and pull up on the handle. Remove the four screws where the top half connects to the bottom half. Two on the outside back and two on the inside front where the bag goes. You'll need a long philli ... Electrolux Vacuums

How do I remove a broken wheel on a Electrolux Epic 3500 SR

... Electrolux Epic 3500 Vacuum

My Electrolux Regency Series upright vacuum brush motor does not activate. Cleaned the brush and press reset to no avail. Opened handle switch assembly and checked each wire attached to all three switch settings. Tried disassembling brush assembly but could not pry open after removing all screws.

... Electrolux Vacuums

Removing D720 electrolux motor for replacement

... Vacuums

My Electrolux Epic 6500 SR will not turn off by pressing on the switch button. I took it apart and removed the switch assy. I can maunually turn it off & on by pressing the rocker arm on the switch assy. It appears that the problem is with the big blue operator button, not the switch assy itself. The button does not seem to press down enough to cause the rocker arm to switch. The button has a "U" shaped wire that presses on the rocker arm and it may have some broken plastic details at the b

WOW !!! Finally You are dead on, absolutely 100%.... good work!!!.Get only a genuine new switch button with spring from an AERUS Electrolux dealer and reinstall. Then carefully reassemble the entire body and wiring harness.Con ... Electrolux Epic 6500 Vacuum

Motor removal - Electrolux UltraLux 2000 Bagged Canister Vacuum

The body on this unit split apart at the bumpers. You will open the front lid and slide the bumpers and the internal slides forward to separate the panels then the rear housing will drop off. At that point you must gently separate the halves by openi ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I want to change the motor on my Electrolux 6500 Epic. How do you get the shell open?

Some use computer proof torx screws,youll ned a v long screwdriver.cheaper to buy another one new ... Electrolux Epic 6500 Vacuum

Hello. We have an electrolux super J canister vaccum. Its fan is broken. How can I remove the fan from the motor axel ?Where can I get a new fan ? Looking forward to your reply, Robert

Japanese AV ****, Asian Femdom, Slave Domination & Bdsm\015\012\015\012http://www.avbondage.com ... Electrolux Vacuums

We replaced the motor on our electrolux epic 6500 but the temperture light comes on and machine willnot run.

If you replaced it yourself with an original motor you have the thermal temp wire crossed over inside the body housing. This canister has a VERY specific almost foolproof harness. If you look carefully at the wires the only reach to their exac ... Electrolux Epic 6500 Vacuum

The motor running the beater bar on ny Electrolux canister vacuum cleaner runs intermittently. It runs about 2 minutes and then cuts off and automatically starts again after a 1 to 2 minute interval. I have tried taking it apart and removing the dust and grit in the beater bar attachment but with no change in operation. What would you suggest?

Check all the wiring connections to make sure they're tight. \015\0121/2. Wiring to power nozzle motor or reset switch is loose.\015\0121. Cord from power nozzle to upper wand. If the plastic portion of the wand is cracked near the co ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Our unit is 7024A Electrolux Oxygen 3 - it seems to work great but suddenly, the head or 'power brush' or whatever it is called - has died. I checked by removing the hose and plugging it directly into the body, but it is still dead. Without that motorized head working, the vacuum is useless. Is it worth replacing? The unit is only about 1 year old and has seen light use only. Very frustrating, since it was the most expensive unit in the store:(

... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Electrolux epic 6500 turns off with new bag installed and hose removed. How do I get the control valve out to check it...?

... Electrolux LE, 2100, 6500 Canister Bag Lock Out Valve

My Electrolux Epic 6500 will not turn on. I have no indicator lights other than power cord is connected. Prior to the vacuum not working the motor seemed to be going slower and slower till it stopped completely.What could my problem be and how would I then test to confirm?

... Electrolux Epic 6500 Vacuum

Electrolux epic series 6500sr remove elbow from hose

... Electrolux Epic 6500 Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 1.6193 seconds