Having problems with your Electrolux Epic 6500 Vacuum ?

Where can I get motor brushes for an Epic 6500 SR


Answers :

You can get these brushes at and AERUS ELECTROLUX repair center. However be aware this is a hi rpm motor.
Unlike lower output, heavy duty motrs from 40 years ago, BRUSHES CAN SELDOM BE REPLACED ON THEIR OWN. IF YOU CAN ACTUALLY GET ALL THE WAY IN AND OUT OF THIS VAC , THEN YOU ARE CAPABLE OF THE MOTOR WORK AS WELL.
Once the motor is removed from its housing be sure to inspect the commutator surface for gapping between the segments, the lines must be parallel nor should the com show apple core shaped wear. Either one will negate new brushes.
New brushes are best seated with a fine abrasive commutator stone and run in at half speed & half voltage to allow them to gradually seat, especially on a hi RPM motor.
Post back if you need help. Good effort !!!!
Repair Help & Product Troubleshooting for Electrolux Epic 6500 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Where can I get motor brushes for an Epic 6500 SR


You can get these brushes at and AERUS ELECTROLUX repair center. However be aware this is a hi rpm motor. Unlike lower output, heavy duty motrs from 40 years ago, BRUSHES CAN SELDOM BE REPLACED ON THEIR OWN. IF YOU CAN ACTUALLY GET ALL THE WAY ... Electrolux Epic 6500 Vacuum

Flames and fine carbon particles came out of my Dydon DC29 which also partly melted the bottom filter. The motor is still working tho. I feel that the brushes are gone. How to get to the motor and where to get new brushes???


Hi Joel,I'm sorry to hear about your experience with your DC29. We'd appreciate the opportunity to provide further assistance, so if possible, please call us on 1800 239 766. Alternatively, if you email your contact details to us at ... Dyson Vacuums

Not exactly a blow gun. Convertible blower/vac - Sears Craftsman. Wire broke off ONE brush in the motor. Paid about $90 for the vac - Sears lists the WHOLE motor as one part - $88. Have requested brushes (they are provided with a lot of my 'cheap' Harbor Freight tools) but no go. Just get the canned reply - buy the whole motor. Actually got it working again... CAREFULLY drilled and tapped a 4-40 screw into the brush and soldered the lead to that... Always a way, isn't there?


... Vacuums

Need to replace motor brushes on Kenmore canister vacuum 116.25914503 - Getting lots of arcing at brush ends. Need tear-down steps to get at the brushes.


If you can see the arcing you are likely in the motor housing. The brushes are specific to the motor depending on RPM. Most brushes and motors in Sears units are supplied by AMTEK Lamb. The color on the plastic housing and stamped model # on motor w ... Vacuums

Carbon brushes on ME-48 power head motor worn out. Where can I get replacement brushes? Motor is O 90197X7, Lamb, Model 118173-73 - 240V 50/60Hz


Hi Les,Most sites sell only the motor.Here's a website that includes motor brushes: http://www.kleen-ritecorp.com/search.aspx?IsSubmit=true&searchTerm=lamb+motor&gclid=CIbZ59zwiKgCFQprKgod8W2itQHope you can find the righ ... Filter Queen Vacuums

I have a VAX V12 vacuum cleaner which suddenly stopped. The smell indicated Carbon Brush Problems. I contacted a service agent who told me that it was not possible to change the Carbon Brushes brushes on this model and they would need to change the Motor Unit.. To me this sounds very unlikely. Two questions please. Is it possible to change the Carbon Brushes and how do I get the cabinet apart which looks very difficult. I am well qualified electrically to do this job. Regards James Beech


... Vacuums

Bad Motor? I have an upright Electrolux Prolux Heavy Duty "Appareil Industriel" and the motor does not seem to be working and turning the brush. Is there a trip switch somewhere to try and reset the motor? I have taken the plastic cover off on the base of the unit and cleaned it well, but can't seem to get the motor to start again.


... Electrolux Vacuums

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .


Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a CT600 power brush that would not power up. Thinking the motor was bad in it, I replaced it with a new CT700 power brush, I am still experiencing the same problem the power brush itself does not seem to be getting electic power, but the Vacuum unit does come on with suction.


First try connecting the power nozzle directly to the hose. If it works, the problem is due to a broken wire or faulty connection in the wands. At least one wand will need to be replaced.\015\012My guess is it's probably due to a broken or di ... Broan-NuTone VX550 Bagged Central System Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the


Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

Rotating brush Hello, my kenmore rotating brush is not spinning at all, and its causing the motor to cut the belt. should i get a new brush? Thank you.


Sounds like the brush roll has an end that is melted or frozen up so it won't move, in which case you need to replace it. ... Vacuums

I have an Electrolux LITE upright carpet cleaner - about 15 years old. Suddenly last night when using it, from the normal motor (whooshing) sound, the motor suddenly went very slow and with a slight grinding sound. The brushes are now just turning round very slowly and areobviously not picking up anything. Has the motor gone or is this repairable, or should I just get a new cleaner? I have tried to open the machine from the bottom to see if anything is obviously wrong, but it looks complicated a


... Electrolux Vacuums

Motor smells I have the same problem. Did you get this fixed? Was the problem the motor or the brushes. I don't want to spend $80 for the motor KC92FCJNZ000 is there another way to repair this?


... Kenmore Vacuums

Panasonic power brush with dual edge cleaning 12 amps rottating brush doen't move..motor runs but brush not...how to get inside unit to fix it ... Thanks Robert


... Panasonic MC-V9638 Bagged Canister Vacuum

Is there a trick to getting the belt on the motor pulley and brush on the Hoover Elite Supreme


Hi ,try warming the belt up in hot water first it will stretch better\011 ... Vacuums

Need to open rotating brush part of vacumm as motor functioning but roller not turning...perhaps belt broken put need to get into ..inside brush box ...Need help need instruction with diagrams Thanks for help Robert


... Panasonic MC-V9638 Bagged Canister Vacuum

Scrub brushes will not turn on a Hoover F7425-900. How to disassemble the top end to get to the brush motor


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hi, i was able to get to my electrolux epic series 6500 motor. i know that my bearing is broken inside the motor but i am not able to remove the metal plates around the fans. how can i do so? thanls


You don't. This motor is not designed to come apart, not even by Electrolux service techs. The whole motor has got to be replaced. ... Electrolux Epic 6500 Vacuum

Vacuum motor overheating. Never happened before till last nite and today. It seems to be getting hot and tripping an overload switch or something like that. Starts back up after a long cooldown. Roller brush will still come on, even though the vacuum motor will not. Any idea what may be causing that?


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My vacuum stopped and thinking it is the brushes. Bagless wind tunnel,rewind,cyclonic, Question is: how to get to the motor sio I can check the brushes? Had it since Feb,08


... Hoover 5416-900 WindTunnel Bagged Upright Vacuum

I have a dyson dc14 how do i repair my vacum? i need to try to replace the brush bar motor or something so that i can get the brush bar to work again.i hope you can help me out


Brushbar not spinning:--\015\012Ensure brush control is set on carpets mode. Note: brushbar will only spin when\015\012the handle is reclined.\015\012To get user manual for your vacuum please click on the link mentioned below\015\012 ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Screeching sound coming from motor area,smell of burning,motor speed dies down and speeds up , screeching gets worse. carbon brushes are ok.


How is the fan, any fins broke off? Could be bad motor bearings, problem with the armature. ... Kirby G4 Bagged Upright Vacuum

Eureka 5893avz 4d vacuum brush motor will not run. Push reset botton doesn't start. where can I get a motor. [email protected] Thank you


... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

I have a roomba 530 pet series. It appears that the brushes aren't turning. They are free of dirt and debris and move easily when manually turned. But, You can tell there may not be a motor turning, because the roomba is more quiet than normal when you turn it on. Also, the hair just collects along the bottom of the brush and doesn't get pushed into the bin.


The belt either broke or has come off the track.... this should be easily accessable from the underside of vaccuum ... iRobot Vacuums

I have a Electrolux cannister Type Epic 6500 SR vacuum cleaner. The motor is making a whining noise on shutdown. What is the trick to opening it to get to the motor? THANKS, John


Hi there,the best thing you can do, is to disassemble the casing of the unit, ... Electrolux Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0661 seconds