Having problems with your Electrolux Epic 6500 Vacuum ?

Electrolux Epic 6500 Powerhead Motor

\015 The cannister works but not the powerhead. When I took it apart I found the motor rusted and it will not turn even the slightest bit. Where can I find a motor replacement for the powerhead?\015

Answers :

Could be the connections inside the swivel just above the powerhead. They slide on and could come off if the powerhead is abused in some odd way...
Call an Aerus Electrolux dealer in your area.
Repair Help & Product Troubleshooting for Electrolux Epic 6500 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Electrolux Epic 6500 Powerhead Motor


Could be the connections inside the swivel just above the powerhead. They slide on and could come off if the powerhead is abused in some odd way... ... Electrolux Epic 6500 Vacuum

My electrolux epic 6500sr vacuum has a seized motor. How do I acess the motor to service or change it? There are no obvious screws or clips to open the motor outer case


... Vacuums

Hi, i was able to get to my electrolux epic series 6500 motor. i know that my bearing is broken inside the motor but i am not able to remove the metal plates around the fans. how can i do so? thanls


You don't. This motor is not designed to come apart, not even by Electrolux service techs. The whole motor has got to be replaced. ... Electrolux Epic 6500 Vacuum

I have a Electrolux cannister Type Epic 6500 SR vacuum cleaner. The motor is making a whining noise on shutdown. What is the trick to opening it to get to the motor? THANKS, John


Hi there,the best thing you can do, is to disassemble the casing of the unit, ... Electrolux Vacuums

Replace vacuum motor on a Electrolux Epic 6500 sr


... Electrolux Epic 6500 Vacuum

REMOVING AN ELECTROLUX EPIC 3500 MOTOR


... Electrolux Epic 3500 Vacuum

I want to change the motor on my Electrolux 6500 Epic. How do you get the shell open?


Some use computer proof torx screws,youll ned a v long screwdriver.cheaper to buy another one new ... Electrolux Epic 6500 Vacuum

We replaced the motor on our electrolux epic 6500 but the temperture light comes on and machine willnot run.


If you replaced it yourself with an original motor you have the thermal temp wire crossed over inside the body housing. This canister has a VERY specific almost foolproof harness. If you look carefully at the wires the only reach to their exac ... Electrolux Epic 6500 Vacuum

Electrolux epic 3000 not working on carpet setting. Belt is not broken. Could it be switch or motor?


... Electrolux Vacuums

Electrolux central vac powerhead (N106M) frequently tripping built-in circuit breaker. It seems to be only when pushing in one direction, why would the motor draw more current in one direction? (it doesn't seem to be related to carpet "grain")


Have you checked the roller brush. Thread, string, and hair wrapped around the brush will create stess on the motor, resulting in overheating and shut off. Clean the brush and try. ... Electrolux Centralux Vacuum

My Electrolux Epic 6500 will not turn on. I have no indicator lights other than power cord is connected. Prior to the vacuum not working the motor seemed to be going slower and slower till it stopped completely.What could my problem be and how would I then test to confirm?


... Electrolux Epic 6500 Vacuum

Hi I have an electrolux vacumm cleaner, super J model. My problem is that the powerhead only works if the switch is in the off position. vacumm motor works in the on position, opposite of each other. Can anyone help? Model 1401


Looks like there's an interchanged wires in your vacuum. Both the motor and the powerhead must go together. Check it up. Leave themotor wiring connection intact. Just tinker and check the powerheadwiring connection . ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Electrolux Epic overheating


It stays closed until the temp. is excedded, then opens. Does the motor shaft turn easily or does it drag. If it drags, then that is what is causing the heat problem. Not sure what it should read, it could be bad, but it should read low ohmns, so ... Electrolux Epic 6500 Vacuum

Electrolux Centralux I have a Electrolux Centralux. When I plug the hose in at one of the wall outlets the motor will not start. If I go to the motor and slap the unit it will start.....then...it will not stop unless I unplug the power cord to the motor. If I plug the power cord back in, the unit will not restart until I slap the motor unit again. The unit has only been used 20 - 30 times. Any suggestions?? Thanks, Bruce


I dont know if you had your unit looked at yet but it sounds like the Power module is going. I repair the machines so I know some of the work. ... Electrolux Centralux Vacuum

Repair manual for Electrolux EPIC 6500 SR


I don't have a manual for these but the trickiest thing about these units is taking them apart. If you have an Aerus/Electrolux dealer near you, it's not a bad investment to have them install the motor for you. You would probably receive a warranty w ... Electrolux Epic 6500 Vacuum

Lubrication for powerhead motor


The power head motor dose need service first thing you should do is take the top cover off by removing the screws on the bottom of power head then remove brushtroll clean brushroll and the end bearings make sure they spin freely squirt some lube (w ... Vacuums

Electrolux Epic 6500 SR cord will not rewind - Electrolux Epic 6500 Vacuum


Unfortunately most cord reels cannot be repaired and must be replaced as a unit. That Vac Guy ... Electrolux Epic 6500 Vacuum

Replace belt on powerhead of electrolux 9000 - Electrolux Compact Canister Vacuum Powerhead Belt


... Electrolux Compact Canister Vacuum Powerhead Belt

Bad Motor? I have an upright Electrolux Prolux Heavy Duty "Appareil Industriel" and the motor does not seem to be working and turning the brush. Is there a trip switch somewhere to try and reset the motor? I have taken the plastic cover off on the base of the unit and cleaned it well, but can't seem to get the motor to start again.


... Electrolux Vacuums

I have an electrolux epic tank... new bag..not plugged...starts and then shuts off


... Electrolux Vacuums

Electrolux EPIC 6500 won't stay on


My suggestion for this is simply get a new on and off switch to put on it and this should fix the pronblem ... Electrolux Epic 6500 Vacuum

Replace power switch - Electrolux Epic series 6500


Well, i post an answer in the wrong field, and i can't find it, so i will type one more time.slide two vinyl side pieces off, and remove top halves. remove two screws from the switch, and remove it from top halve. between switch and outside but ... Electrolux Epic 6500 Vacuum

How do I gain access to the motor of an Electrolux 2000 canister vacuum. The air intake on the motor must be partially blocked as there is a loss of suction and the motor makes that high pitched whine like it does when you cover the hose with your hand


Dismantling the vacuum probably won't help much, and reassembling can be a bear. \015\012To check the intake, remove bag and look into bottom of bag well. It there's a filter there, remove it and check intake at bottom of bag well. Clear if t ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I have an Electrolux LITE upright carpet cleaner - about 15 years old. Suddenly last night when using it, from the normal motor (whooshing) sound, the motor suddenly went very slow and with a slight grinding sound. The brushes are now just turning round very slowly and areobviously not picking up anything. Has the motor gone or is this repairable, or should I just get a new cleaner? I have tried to open the machine from the bottom to see if anything is obviously wrong, but it looks complicated a


... Electrolux Vacuums

I have a Filter Queen Majestic 360 and am having problems with the powerhead. There is a loud rattling noise in the powerhead, especially when I vacuum thicker carpet. I have replaced the motor, roller brush, and belt, but the rattling remains. It sounds like it is coming from the roller brush area,and when I turn the powerhead over, it rolls free and sounds fine. Any thoughts?


Hi there, as per your information i guess its a problem of power transformer. He can't supply the proper power in the motor & thats why the noise will come from the transformer. Thanks & waiting for your feedback. ... Filter Queen Majestic Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0348 seconds