Having problems with your Electrolux Epic 6500 Vacuum ?

When I vacuum with the power nozzle, it keeps cutting off. Do I need to replace the hose or the power nozzle?


Answers :

Not necessarily. It's hard to tell without checking it out. I strongly recommend taking it to an authorized Aerus Electrolux store and letting the service tech check it.
\015\012If you have the "Sidekick", you can try using it. If it still cuts out, it's the hose. If not, the wiring in the power nozzle is loose or worn and needs to be replaced.
\015\012Keep in mind that you may not need to replace the hose or power nozzle, just have some wiring repaired.
Repair Help & Product Troubleshooting for Electrolux Epic 6500 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When I vacuum with the power nozzle, it keeps cutting off. Do I need to replace the hose or the power nozzle?


Not necessarily. It's hard to tell without checking it out. I strongly recommend taking it to an authorized Aerus Electrolux store and letting the service tech check it.\015\012If you have the "Sidekick", you can try using it. If it still cu ... Electrolux Epic 6500 Vacuum

Where do you hook the clear hose that is in the compartment with the motor ? Second where the vacuum hose connects to the bag it keeps cutting in and out of power. I replaced the female cord to motor and still cuts out."no suction "


Would you care to tell us the make and model of the vacuum you're asking about? ... Vacuums

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?


Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

Need to replace belt in Kenmore Vacuum Power-mate nozzle


Hello,\015\012\015\012Here's what you'll need to replace a belt on a Kenmore canister vacuum:\015\012\015\012- Phillips Head Screw Driver\015\012- Flat Head Screw Driver\015\012\015\012There are two different ... Kenmore 23313 Whispertone Bagged Canister Vacuum

My electrolux 2100 vacuum hose broke. I replaced the hose but now I dop not have power at the hose end. is there a curcuit breaker in the canister tha supplies power to the hose??


... Electrolux Guardian Bagged Canister Vacuum

Power nozzle of my S3670 does not work (vacuum itself does work), the headlight bulb in the nozzle is broken. This happened in the past several times - we would bring the vacuum to service center - I don't know what they did other than replacing the bulb. I decided to go to ACE and buy replacement bulb myself, replaced the one in the nozzle - this did not fix the problem. I don't see any fuzes or anything in the nozzle. However, the manuals says to "Use only HOOVER part no. 27317307, which is a


... Hoover S3670 Bagged Canister Vacuum

I need a replacement belt for my central vacuum power nozzle.


Do you know the brand or model? If not you can get replacement central vacuum belts here:\015\012\015\012Replacement ... Vacuums

I have an Electrolux Epic 6500 SR vacuum and the hose end with the handle is separating. Power nozzle losing contact intermittently. Is this piece replaceable or repairable?


It is replaceable. Just take it to the nearest Aerus Electrolux store and the service tech will take care of it for you.\015\012Go to the following site and follow instructions to find the stores nearest you. ... Electrolux Epic 6500 Vacuum

I have a electrolux oxy3 system vacuum cleaner. The floor is damaged, and the hose has been damaged and severed and the copper cables have been cut...so I need to purchase a replacement foot and hose/hand piece. regards Sandy


... Electrolux Vacuums

I need to replace the belt on the power nozzle of my Hoover Dimension 1000 Model S3491. Unfortunately, I have no written instructions on how to do so. I purchased the vacuum cleaner in the mid-80s. Are the instructions still available? Thanks in advance.


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=566792\015\012Generic problem for all Vacuums\015\012I need to replace the\015\012posted by Deb in Iowa ... Vacuums

Need to twist hose to keep power on


The loose connection will be internally and in some cases is not detected visually.\015\012Do you have any connector where they connect together? ... Kenmore 22812 Bagged Canister Vacuum

I need a new power cord for the power nozzle on my Electrolux 2100 canister vacuum. The power nozzle has part number N115M written on the bottom. I have found the power cord for power nozzles PN6 and PN7 online, and it looks identical in photos but I'm not sure if it's the right part.


You can buy the hose at an authorized Aerus Electrolux store. If near enough, they will deliver, if too far, they can ship it. The nearest dealer can be found using the below link. Just follow the instructions.\015\012Just provide the model ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Replace on/off switch on rainbow D3 vacuum - Rainbow D3 Canister Vacuum Cleaner Power Nozzle Reset Switch Vac Cleaner Power Nozzle Reset Switch


... Rainbow D3 Canister Vacuum Cleaner Power Nozzle Reset Switch Vac Cleaner Power Nozzle Reset Switch

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu


This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

Hi. Bought a M3888-3 Royalcylinder vacuum from Lidl. Lost manual that came with it. Only had it 4 mths. Need new hose. Plastic hose has snapped near whereit attaches to metal hose. Can I get a replacement hose from somewhere in U.K.? I know the vacuum is from Germany.


... Royal Vacuums

Replaced internal pump. Color coded hoses for replacement. Marker has worn off hoses. Need proper routing of hoses from clean water tank, to heater to spray nozzles. An internal schematic of hose routing is preferred.


Hi\015\012\015\012Thanks for using FixYa. Please remove the top cover of your Bissell cleaner. Now place the Auto-Mix selector knob to the water only position. Turn the cover over. You will notice an angle on the ... Vacuums

My mother purchased a replacement hose assembly for a Bissell ProHeat 2X and the part was shipped without any instructions... While I am pretty handy, my issue is with the supply tube, and I cant figure out how to accomplish the replacement, and as its not MY vacuum, Im hesitant to start taking things apart.I just need instructions to replace the entire hose assembly.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Power nozzle on E-series won't start when cold unless the red 'reset' button is pressed multiple times while also holding the trigger to 'warm it up'...this is w/the power nozzle off the floor - no restriction on it turning. Once it's been running and then turned off the button must be pressed w/the trigger to get it to run - again w/the nozzle off the floor. It also seems to shut off too easily while vacuuming. I replaced the motor,which didn't fix it. Is the reset switch next on my list? T


... Rainbow E series Canister Wet/Dry Vacuum

I have a Zanussi 1700W bagless upright vacuum cleaner which keeps cutting out after about 5/10 mins use. I had to replace the rubber drive belt which snapped not long after purchasing and it was fine for a while, but now its just keeps cutting out after a small amount of use. Nothing wrong with belt which is still intact so we don't know what the problem is. It's a great cleaner otherwise - but it's driving us mad!! Please help!


... Vacuums

Vacuum Problem My dirt devil vacuum is losing suction and keeps clogging. All the dirt keeps sticking to the screen by the filter and then it would stop working. Also the hose does not have a strong suction power either. So what can I do?


The Bissell can have several filters in it, depending on the model. Some have a round hepa filter that is covered with a foam sleeve. This filter is located at the bottom of the dirt cup. Others have a foam filter that is located under the dirt cup i ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK. Mine is so loud I can't use it very long-high pitch screech. Can this be fixed or does the whole vacuum need to be replaced? It still cleans gr


Sounds like a bad motor. Could be either foot motor or main motor either way cost will be more than half of the unit. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have a power drive baggless vacuum cleaner...it runs well, but suddenly it seems to have lost most of the suction coming through the hose and floor area. When I remove the dirt container, the suction below it seems strong. I have had it to repair twice--they have tuned it up and replaced all filters and belt. It still does not pick up well when I vacuum or use the hose. Can you help ?


There is something stopping it up,you will have to dissasemble the unit to find the blockage,this is the most likely problem. ... Hoover U6660-900 WindTunnel Bagless Upright Vacuum

Power Head keeps cutting in and out while vacuuming???Canister motor keeps running but the power head starts and stops like there is a short or some loss of connection somewhere. Any ideas?


My kenmore progressive vacuum had the same problem. The electrical terminal at the bottom of the wand was corroded. I used a flat head screw driver to scrape the female portion of the connector as best as I could. I then took off the plastic cover on ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

I just bought this vacuum at a second hand store. My girlfriend told me to grab it as it such a quailty product. How ever I can't find a model number or anything else. I need a manual please. Does it take bags? Do I need to replace the filter or just wash the one I have? It is black and silver, cannister. It also says big gary's vacuum system warehouse in surry British Columbia, Canada. It also says to use filter pow-r-nozzle 96. I have no idea of the year.


I suggest you google what you know. I dont think anyone here can suggest where you can get a manual for a machine you dont even know the name of.\015\012\015\012You ask about a bag ... I dont know ... is there one in it now? You ask abo ... Vacuums

Power nozzle cuts out while vacuuming


... Eureka Oxygen 6996 Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1508 seconds