Having problems with your Electrolux Epic 6500 Vacuum ?

I have an Electrolux Epic 6500 SR vacuum and the hose end with the handle is separating. Power nozzle losing contact intermittently. Is this piece replaceable or repairable?

Answers :

It is replaceable. Just take it to the nearest Aerus Electrolux store and the service tech will take care of it for you.
\015\012Go to the following site and follow instructions to find the stores nearest you.
Repair Help & Product Troubleshooting for Electrolux Epic 6500 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have an Electrolux Epic 6500 SR vacuum and the hose end with the handle is separating. Power nozzle losing contact intermittently. Is this piece replaceable or repairable?

It is replaceable. Just take it to the nearest Aerus Electrolux store and the service tech will take care of it for you.\015\012Go to the following site and follow instructions to find the stores nearest you. ... Electrolux Epic 6500 Vacuum

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter

There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

Power Nozzle Model No. N137A (for Electrolux Epic Serial 6500 SR) has a broken wire. Can I get a replacement power nozzle or find a repair place in the Everett, Washington vicinity?

... Electrolux Epic 6500 Vacuum

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless

Get over it and buy a new one!!! ... Vacuums

My 8 yr old kenmore vacuum works well - however the hose has worn under the handle where there is a hole (resulting in decreased suction power). I'd like instructions on opening the handle and bypassing the worn piece of tubing rather than replacing it for $129. Some of the handle screws remove easily but the last one doesn't loosen easily.

Hi,Have you tried spraying the stubborn screw with WD40 and let it soaked for a while? Other than these screws holding the handle together, there would no other way of opening it up. Hope this be of initial help/idea. ... Kenmore Vacuums

I have an L shaped piece of metal with a hole at one end that fell out of my hoover elite bagged upright vaccuum cleaner. I repaired the belt but don't know where this metal piece goes. I think it has something to do with the wheel assembly which is replaced and it seems to want to stay there. any thoughts

This metal clip was for the wheel assembly, but not always needed. you can diregard the part if your vac is working correctly with the front wheels. ... Hoover Elite U5061-900 Bagged Upright Vacuum

Electrolux Epic 6500 SR ...no power to power nozzle. I think it is the switch in the handle because if I use my friend's hose/handle (same model), my power nozzle works fine when I turn on the switch. If you think it is the switch, can I get a part for it?

That's about the best one to narrow down a problem, however, there could also be a break in your hose wiring. Switches, hoses, and hose handle assemblies are all available at your local Aerus Electrolux store. Simply take your entire machine in so ... Vacuums

How do I replace or repair my tristar power nozzle cordI don't know how to get to or how difficult it will be. there is a short in wire because it is separating from the power nozzle.

Dear kerri_clark,Can't you take a picture of tristar power nozzle cord that you mean.I need to take a look at this to assist you further more.regards,dm ... Vacuums

Repairing contacts in Electrolux Z8240 handle

Hi There, Alec From VacuumSpot here. I work as a vacuum technician and unfortunately I am the bearer of bad news the handle is not really repairable. Even in warranty Electrol ... Electrolux Vacuums

Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a '97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I'm sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa

Honestly you should take it to a vac.shop they can fix any vac. ... Windsor SR12 Sensor Bagged Upright Vacuum

I have the Polti Vaporetto model VTT 2085 FIE 74, year of manufacture 1998; my son managed to lose the large brush. I would like to purchase a replacement large brush and also the round brush for the 120 degree C jet nozzle. I also want to buy some cotton cloths for the large brush and for the small brush. Where can I obtain these parts and cloths?

... Vacuums

I have a bissell proheatX2. it has quit spraying to the floor and out of upholstery hose. I contacted bissell who won't do anything, they refered me to a repair shop which told me i need to take the heater out of handle and unclog it. How do i do this, is there a disassembly proceedure?

... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The power head keeps shorting out during use. one of the connecting prongs from the handle to the power head is black instead of silver and is smaller in diameter like it has been arcing inside the connection. could this be the problem and if so can I replace it or will I have to take it to a repair facility. Thank you for your help, Jim Carey [email protected]

This is a problem with the connection in the wands and the powerhead. Because they are shorting out you may have to replace the neck on the power nozzle. (Leave that to a pro). But you will definatly have to purchase a new wand as replacement wires a ... Electrolux Lux 7000 Bagged Canister Vacuum

Stand up lever is plastic, broke when stepped on to release handle, can it be repaired, replaced with a better one, plastic breaks too easily?

The pedal release can be replaced but the base will need to be checked for cracks as well. if the base is broken most common is the socket the pedal release snaps into. some of the plastic parts have been made with better materials ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

I have Dyson DC05. The plastic clip from handle to the metal pipe is broken. Can this be repaired or do I need to replace the whole metal pipe section? If so where can I do this.

Dear Madam/SirThis is very simple problem. the problem can be solved in a very simple manner.As you have told me that the plastic grip from the handle to the metal pipe is broken.You Can do it near by any welding s ... Dyson Vacuums

I have owned 4 sebo uprite vacs. Every one of them has the same problem. Where the handle connects to the vac it break contact and shuts off and on. It seems the connection between these two parts is very weak. The only answer I get from my local repair shop is

Well you now know the error of your ways, don't buy another!The best fix is to remove the connectors and connect the wires directly together. ... Century 400 UVAC Vacuum

Rod problem... One of the electrical connection posts that are on the top of the rod appears to be broken which causes the power head to work only when it makes contact. Is this repairable? If not, is it replaceable? If not, are the rods available for purchase? The vacuum cleaner itself works well,

You would need a new wand. this might work for your unit. ... Fantom Vacums Lighting Canister Vacuum

Mrs Cleaner flex has pulled out how do I replace Electric supply wire to switch on handle has broken at switch. How do you remove switch to repair? tonysimmons

Hi\015\012\015\012\015\012\015\012\015\012\015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I am trying to replace the power cord for my 82 year old father-in-law's Oreck XL 2600HH. He already took it apart. I need to know where the semi U shaped spring steel piece is supposed to go inside the Helping Hand Handle? Any drawings or schematics available? Thank you for your time. Arthur

That justs lies on the inner handle whenb you put the spring back. There should be two holds where each end of the spring sits in. ... Oreck XL Ultra Bagged Upright Vacuum

There was a foam piece above the motor of my rainbow d4c power nozzle. When I took the plate off it desintigrated and fell off. Was that supposed to be there? If so how do I find a replacement?

You said "above the motor", so I assume you meant the smaller foam piece located there, and not the gasket seal that is affixed to the inside of the metal bottom plate, (which is what the previous solution responder was referring to).Most ... Rainbow 75th Anniversary Canister Vacuum

The hose does not stay connected to the wand although the collar appears to be locked in place for a while. Is there a replacement part for this? Also the holder where the wand goes in has split horizontally. This appears to be one piece with the body of the unit. Is it repairable? It still holds the wand but continues to get worse.

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Power nozzle of my S3670 does not work (vacuum itself does work), the headlight bulb in the nozzle is broken. This happened in the past several times - we would bring the vacuum to service center - I don't know what they did other than replacing the bulb. I decided to go to ACE and buy replacement bulb myself, replaced the one in the nozzle - this did not fix the problem. I don't see any fuzes or anything in the nozzle. However, the manuals says to "Use only HOOVER part no. 27317307, which is a

... Hoover S3670 Bagged Canister Vacuum

How to replace Hoover PowerMAX power nozzle cord?

... Hoover Powermax S3601 Bagged Canister Vacuum

Beam Soft Touch handle electric harness replacement

Set the bottom part of the handle down(not the part that the screws go in)the contact board will fit into slots on the left side of thehandle half, the switch will go where the cutout is for it on the top, the plug is notched to fit at the lower fron ... Beam Industries Wet/Dry Auto Central System Vacuum

Whispertone powerhead handle release replacement

Take a butter knife and/or flat head screwdriver and press forward on the four tabs that retain the pedal. ... Kenmore 23313 Whispertone Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0761 seconds