Having problems with your Electrolux Epic 6500 Vacuum ?

Hi, i was able to get to my electrolux epic series 6500 motor. i know that my bearing is broken inside the motor but i am not able to remove the metal plates around the fans. how can i do so? thanls


Answers :

You don't. This motor is not designed to come apart, not even by Electrolux service techs. The whole motor has got to be replaced.
Repair Help & Product Troubleshooting for Electrolux Epic 6500 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi, i was able to get to my electrolux epic series 6500 motor. i know that my bearing is broken inside the motor but i am not able to remove the metal plates around the fans. how can i do so? thanls


You don't. This motor is not designed to come apart, not even by Electrolux service techs. The whole motor has got to be replaced. ... Electrolux Epic 6500 Vacuum

Sanitaire Model S661 Type A, heavy duty commercial motor, 8840 watts. A large nail was accidentally vacuumed. There was immediate noise, and then it smelled like smoke. We can see after removing the bottom plate that the translucent plastic fan was completely broken. Can it be replaced? We have no repair service nearby.


... Eureka Sanitaire S661 Bagged Upright Vacuum

Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?


I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb


Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

Hi On a Hoover convertable model U4497-900 I'm trying to replace the fan. The old fan cracked, then flew apart. I have the new fan, have the motor assembly removed, but can't seem to get the pulley nut off the motor to replace the fan. Is there a trick to this or should I just try to muscle it? Thanks.


... Vacuums

Fan replacement I found the part to replace my broken fan. I've remove many screws, but I can't remove, what seems to be, the obvious plate to get to the broken fan.


Http://reviews.ebay.com/KIRBY-VACUUM-REPAIR-HOW-TO-REPLACE-THE-FAN-IMP ... Kirby Ultimate G Bagged Upright Vacuum

Kirby Heritage II 2HD Vaccum Cleaner. I have removed the housing and reached the motor shaft for the vacuum fan. How do you remove the fan from the shaft.


Hi, you can visit this site to view how to remove the fan from the shaft...http://www.diyonline.com/servlet/GIB_BaseT/diylib_article.html?session.docid=1678Take care ... Vacuums

I have a Kirby Dual Sanitronic '50' Vacuum Cleaner I bought in 1966. The motor does not start when I attach the belt lifter of the rug nozzle. When I remove the rug nozzle and detach the belt from the motor fan shaft the motor starts when I depress the nozzle switch and the power switch . Seems like the brushes in the motor are worn out. I do not have a manual for this unit. Can you assist me as to what newer unit is this compatible to and the problem I'm having at present??


... Kirby Vacuums

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall


That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

Hello. We have an electrolux super J canister vaccum. Its fan is broken. How can I remove the fan from the motor axel ?Where can I get a new fan ? Looking forward to your reply, Robert


Japanese AV ****, Asian Femdom, Slave Domination & Bdsm\015\012\015\012http://www.avbondage.com ... Electrolux Vacuums

How do you remove fan off motor oreck xl9800


... Oreck XL2200 Bagged Upright Vacuum

The vacuum fan disintegrated. Unable to determine how to remove the fan from the motor shart.


Hello,Follow the steps below gradually:Remove your vacuum's power head by first switching the carpet\015\012height adjuster to its highest setting. Turn the belt lifter, making\015\012sure that the two red arrows pictured on t ... Vacuums

Oreck xl9300 Bought a new motor but cant figure how to pull off the metal fan from the old motor. Is it muscle or a trick?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=19810&thid=767429\015\012Oreck XL9300\015\012Posted by Cubfan70 on July 10, 2008\015\012Bought a new motor ... Oreck XL Ultra Bagged Upright Vacuum

I want to take the fan impellar off the motor to clean it. I cant seem to get the metal housing off of the motor. Do you have to take the nut off the impellar If so how do you stop the shaft from turning thank you.


Very simply you dont take the fan out of the motor. it was not made to be removed or cleaned because its not supposed o get dirty if your using good bags in the vacuum. the best you can do is blow it out with an air hose. ... Electrolux Epic 6500 Vacuum

FAN How do you replace the fan/removel of metal plate. i'm upgrading the plastic one to a metal one


Take off the bottom plate, remove the screws for the motor and fan chamber, remove motor from fan housing, remove the nut for the fan. You may have to lock down the armature if the nut is too tight. Replace fan and reinstall motor into the fan hous ... Oreck XL2600 Vacuum

I have a Electrolux , EL6988 Canister Vacum, howeveer the brushes and motor will not run when turned on. I have take the plates and cleaned around the brushes, but it will not come one. The vacum comes on but the motorized bushes do not activate. Thanks I have lost my owners manual, and have looked for the reset button and can't find or know where it is located. Any suggestions.


I need the molded wire harness inside the plastic wand ( one of the prongs is broke off) What is the part # or where can I buy it? Model EL6988 ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom


Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The metal plate at the front of our X4 Extra has been damaged from nail heads on timber floors and although we have straightened it, we now need to replace it. We have ordered the part but cannot see how the plate comes off. We are reasonably practical and should be able to do it if someone can provide some guidance.


... Sebo X4 Bagged Upright Vacuum

The TechDrive Pedal on my Kirby G6 fell out of the back of my vacuum cleaner. I removed the screws from the metal plate one the bottom to try to see if something had come a loose. Can you send me a diagram so I can put it back together or tell me where I can get a service manual. The only part I am having trouble with is the metal piece inside that engages the power drive. Thank you.


The pedal drive fell out . Do you have a manual telling me how to get it together again.. Thanks, Dianne ... Kirby G6 Bagged Upright Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I ran my vacuum against an area rug that has strings around it and a few strings got caught up in the beater bar. Now, the beater bar does not function- the motor runs but the beater bar does not seem to be operating. I removed the strings from the bar.


Hi,\015\012\015\012There is a switch next to the main power switch on the handle which turns the brushbar on and off. When the beater bar becomes obstructed as in your case, there is a safety feature which cuts power to the beater bar. Al ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

PHILIPS MOBILO PLUS 8566 (vacuum)- How to remove motor cover? I have to reach to the fans but I don'r find how to do Please I need a help [email protected] [email protected]


... Vacuums

My Vax Swift Pet Premium has suddenly lost suction. There was a lot of human hair wraped around the brush which I removed but no theres no suction at all. The motor sounds fine.


... Vacuums

Dyson DC07 My DC07 cuts out after 5 mins and I want to replace the thermal cutout. I have cleaned it thoroughly, including the cyclones but it still cuts out. How does the plastic moulding around the motor dismantle? I have started by removing the 4 torx screws but the upper grey housing does not want to detach and I am worried about breaking the plastic. Appreciate any advice.


Try this page: -http://www.fixya.com/support/t192124-overheating_dyson_dc07Regards Gualo ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0697 seconds