Having problems with your Electrolux Epic 6500 Vacuum ?

How do you take the handle apart?

\015 Epic 6500sr\015\012I have a bad contact in my handle. my carpet brush goes on & off as we vaccuum. I have narrowed in down to the handle. How do you take the handle apart?\015

Answers :

Take a box cutter blade or something razor thin and locate the 2 screw covers on the handle. Pry the two covers off and remove the 2 hex screws. Pull handle apart. Done. Might want to check your elbow down on the power nozzle before you rip apart that handle though. 4 out of 5 times, the problem is in the elbow.
Repair Help & Product Troubleshooting for Electrolux Epic 6500 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you take the handle apart?


Take a box cutter blade or something razor thin and locate the 2 screw covers on the handle. Pry the two covers off and remove the 2 hex screws. Pull handle apart. Done. Might want to check your elbow down on the power nozzle before you rip apart ... Electrolux Epic 6500 Vacuum

Floppy handle When I depressed the pedel to lower the handle on our Savvy there was a snap and now the the handle won't stay up. I assume there is a spring or someting else that broke. I can't find an exploded view of the vacumm to to take it apart to find out whats broken. Any ideas on what it is.


You have to take the base cover off to find out what broke,there are some screws on the bottom remove those to take the bottom plate off then,then up inside there are more screws to on the top remove the emblem and take that screw out ,that should e ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Sears 116.31913 Lower units, vacuum motor and agitator power head do not have power/115v to them and won't run. I'm trying to take the handle apart to access the on off switch. I've taken all observable screws out and cannot separate the handle and section immediatly below the handle to access the on/off switch, to trouble shoot. Any tips for separating the plactic pieces enclosing the on/off switch?


... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

My Kenmore progressive canistor vacuum has a loose electrical conection in the hose handle. How do you take the handle apart?


There are 3 visible screws there in the handle and one not so visible. start by removing the 3 visible screws.Take a flat screwdriver and pry off the colored portion of the handle that would contain the switch. There is one mo ... Kenmore 25512/ 25513 Progressive Canister Vacuum

My infinity vac NV29 seems to have an extension wand stuck down in then tube and I am not able to get it out. We rented our winter home and evidently they found some type of extension that did not belong to it. Is there a way to take the handle apart in order to remove it? I am not able to use it with the handle and have to use the one on top of the canister, which is extremly difficult for me since I am disabled. Thank you.


... Euro-Pro Vacuums

I have a Dyson DC22 that seems to have lost a lot of suction. I can't peer right inside the wand, but it seems that hose may have disconnected from the telescoping handle allowing a huge leak. How can I take the handle apart to inspect/fix this?


... Dyson DC22 Motorhead Canister Vacuum Bagless Cyclonic Vacuum

I have a hoover windtunnel upright vacuum, It will not shut off and I have to unplug it to do so. If I take apart the upper handle and manually flip the internal switch it works just fine, only when using the external switch on the handle, wont shut off.


This is a common problem with this machine. The switch has too much resistance to be turned on and off with the switch button and rod. If you put in a new switch, ( # 28161075 ), your problem should be fixed. ... Vacuums

Hi, I vacuumed a small rubber bouncy ball up into the vacuum by mistake. The suction is not as strong now, and I'm not sure what to do. Where I can easily take the hose apart (eg. at the handle places) I cannot find the ball. What do you suggeest?


... Vacuums

My Dyson will not turn on unless I pull the handle back. I have take the entire vacum apart cleaned all blockage and it still will not turn on in the upright position.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

How do you take apart Price Pfister T533-5WW - Price Pfister Genesis T533-5WW White Lever Handle Pullout Faucet


... Price Pfister Genesis T533-5WW White Lever Handle Pullout Faucet

Sock stuck in hose midway. Unable to getit out with wire or brrom handle. Is there a way to take hose apart at either end.


If the sock is midway, taking either or both ends apart won't help. Take it to a vacuum repair shop and ask them to try to unplug it. You may need to buy a new hose. ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

The on off switch is stuck in the on position. I can'tfigure how to take the handle apart. Where can I find an on-line manual? Hoover wind tunnel up-right.


On the windtunnel the switch is not in the handle. It is located in the top of the body housing underneath where the handle meets the body. The slide lever you are pushing on to make the machine run is just a push rod. ... Vacuums

How do I take the handle apart on a Hoover linx vacuum?


... Hoover Platinum LiNX Cordless Stick Vacuum

Take handle apart sebo vacuum - Sebo Automatic X1 Bagged Upright Vacuum


... Sebo Automatic X1 Bagged Upright Vacuum

How to reattach the hoses on the bissell 9200 model after taking it apart


... Bissell Vacuums

Cable stuck in machine (sphera 20). How do I take apart to release cable please? I cannot see any visible screws to take the machine apart. Cable will not retract or come out of machine


... Bosch Vacuums

I need to take the canister apart to screw the filter housing back in place. I can't figure out how to take the canister apart or another way to screw the filter housing back in place.


You did not identify your model and the TriStar website does not provide manuals. They do have a FAQ page which does provide some illustrated guidance which may be helpful. See here:\015\012\015\01 ... Tristar Vacuums

E series How did you take your rainbow e series apart? Do you have a manual? I've got a few pieces off mine but can't see where any other screws are to completly take apart to be able to look at motor. Thanks Kelly


The clear lenses on either side of the top part of the E-series Rainbow are removable. If you look at the each lens you will see two sections on the top edge of each lens that looks like this |___| |___| about 1 1/2 inches in from each end. Put a ... Rainbow E series Canister Wet/Dry Vacuum

Bissell Healthy Home Vacuum brush stopped working. The hose attachment works fine, just the brush on bottom. Without taking it completely apart, it shows no sign of blockage. Any suggestions? Or, will I have to take it apart?


You will have to remove the bottom plate to get at the brush. The drive belt either slipped off or broke, this will have to be replaced. ... Vacuums

I need to take the canister apart to screw the filter housing back in place. I can't figure out how to take the canister apart or another way to screw the filter housing back in place.


... Tristar Vacuums

How to take apart wand of kenmore vacuum 116.24614400 to replace COVER #8191782 on Sears part


... Kenmore Vacuums

Shopvac 90L400 quit working (4 years old). Thought the switch was bad but not the problem. I read that there is a fuse link in the motor that frequently burns up. I tried to take motor apart but not sure of the process. I was able to get to the motor but cannot pull it out of the armature. It appears I have to take the aluminum blower unit off the shaft (it appears to be pressed on with a retaining washer). Do I have to take it off to pull the shaft and motor assembly out? Is that where the fuse


By pass the switch and take power right to the motor leads.. that should tell you if the motor is ok.. have not seen fuse link on a vac motor.. graingers has new motors, but not inexpensive ... Vacuums

I have just purchased two (2) Electrolux Nimble vacuum cleaners. Not one, but both, straight out of the box, the beater bars will not run. It turns on, select carpet, and lower the handle, the red light to check beater bar/or filter lights up. You can reset the light by unplugging the unit, then plugging it back in, but with same results. Now the kicker, if you take out the handle, select carpet, lower the body by the carry handle, it will run and operate correctly, however, as soon as you r


... Vacuums

How do I take apart my Bissell 7920 ProHeat Pro-Tech


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Will not steam. before taking apart is there a


Hi,Look at the manual...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...E ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0455 seconds