Having problems with your Electrolux Epic 6500 Vacuum ?

I can not get the power cord to go back into the canister.

\015 The power cord is pulled out as far as it will go and the recoil will not take it back in. I have an Epic series 6500 SR.\015

Answers :

If you can't get it to go back in by pulling on it, you will need to open up the machine to rewind it by hand. Open the front of the canister and remove the bag. As you are looking at the front of the unit, there are two vinyl coverd strips that run the length of the unit. Pull forward on these strips and then pull out so that the vinyl seperates from the plastic underneath. Now grab the plastic strip with a pair of needle nose pliers and pull towards the front of the canister. These can be tough if the machine has never been opened up before, but pull as hard as you need to, to slide the strip out. Once both strips are out, turn the machine over, pull out on the sides of the bottom of the unit, and lift up. The bottom should come of relatively easily, and eveything will be exposed. You can now see the cordwinder and the spring that pulls the cord back in. If it's not broken, you should be able to manipulate the spring reel by hand and get the cord started so that it will rewind by itself. If not, you probably need to have the cordwinder replaced. Good Luck!!
Very helpful, Thanx
Repair Help & Product Troubleshooting for Electrolux Epic 6500 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I can not get the power cord to go back into the canister.

If you can't get it to go back in by pulling on it, you will need to open up the machine to rewind it by hand. Open the front of the canister and remove the bag. As you are looking at the front of the unit, there are two vinyl coverd strips that run ... Electrolux Epic 6500 Vacuum

No power. I was getting intermittent power with my miele s558 midsize canister, but it was predicated with me fiddling with the retractable cord to get it to come on and then not move the canister while I was vacuuming. Now I can get no power. I have taken it apart and can see no issues with connectors, cord, casings, etc. It all looks fine. It is about 5 years old and I have had no problems with it.

... Miele S558 Red Velvet Bagged Canister Vacuum

I just purchased a Sebo Airbelt D canister vacuum. I plugged it in and used it for ten seconds then turned it off, retracted the power cord and now cannot get the power cord out of the machine. Did I not spend enough money to get a quality product? Does anyone have any idea how to get the power cord out without breaking the machine?

... Vacuums

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa

... Electrolux Vacuums

We bought a new cord winder for our Electrolux 1205 Canister Vacuum cleaner and we are trying to install it is not turning on. We get it all connected but it doesn't turn on. Is there a reset button or some advise you can give me to get it working? I used a voltage detector to see if there was power running through the cord winder and there is.

Did you put a bag in the vacuum?\015\012I suspect there's an improper wire connection somewhere, but there are other things that could cause this I strongly recommend taking it to an authorized Aerus Electrolux dealer and letting a trained tec ... Electrolux Vacuums

Hot cord the cord on my vacuum cleaner has been getting very hot the heat is from one end to the other incuding the plug and also where the cord exits the back of the canister please help I love this vacuum cleaner it has been faithful to me for over 15 years!

Likely after all these years that the motor is starting to go bad and draw more amps thasn it should. a new motor at a vac dealer is your best bet. it was likely made by panasonic, so a new panasonic is your best bet, and less $$$than the kenmore for ... Kenmore 23313 Whispertone Bagged Canister Vacuum

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating

... Vacuums

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!

Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

I installed a new battery in my Roomba 540. It charges and runs directly with power cord but will not charge on dock. When I push the dock button, it acts like it "sees" the dock and approaches it and even slides on, but then gets back off again and just keeps going back and forth until I turn it off.

... Roomba Robotic Floor Bagless Vacuum

Cord rewind The power cord is jammed and won't go in or out. I can't find a way to get the cover off to have a look at it. Any suggestions please? Power cord jammed won't go in or out. Can comeone tell me how to undo the casing to get to the power cord?

Which model do you have.. ... Vacuums

Took my Miele Solaris canister vac in for repair as it wouldn't turn on. The repairman said to come back the next day for the estimate. I called and he said I needed a new cord reel and it would be $189. I drove to his shop and said I would wait to do it later, that I wasn't ready to spend that much. When I came home, it started right up but has no power and doesn't sound right, the noise of the motor is real soft, not as loud as before. I have this terrible feeling that when we decided not to

When you say 'has no power' do you mean , no suction? He may have left the suction hose of the motor and that's why it sounds different. I would call him back and request that he put the machine back to it's original 'state' as it was when you brough ... Vacuums

I have an Electrolux Silverado deluxe canister vacuum that won't run. It was running fine, I turned it off to move the plug and then it won't turn back on. It is getting power to the switch. Any help?

... Electrolux Vacuums

Power cord won't retract back in - Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Canister Vacuum Cleaner - old Model 26412690 Serial #: DF3441912 I need a diagram of the electrical cord retrieval system. I have it disassembled and I need help getting it back together again.

Hello Nurburd !\015\012\015\012Go to the following link , here you will find the service manual for the 26412690 \015\012 ... Kenmore Vacuums

I have a Kenmore canister serial number DB12027279, model 116-2234590. The problem is that the power cord plug gets very hot. Please advise what to do. Thank you.

Just a suggestion, as the debris enters the machine, it has to pass the motor. The motor has vents around it. Enough "debris" gets in that motor, the motor starves for power, which inturns make the media, the cord, work harder.\015\012\01 ... Vacuums

I took apart the power end that goes into the canister to try and get a kleenex out. in doing so i revealed the brass? rings inside also the prong part was taken out. i thought i had everything back in the way it came out but now it will not turn on. is there a reset but or something? thank you

... Panasonic MC-V9644 Bagged Canister Vacuum

My electrolux oxygen canister cuts on and off. I have to open and close the vacuum, or take the base of the hose off and then re-insert. I have to do all these things before it will start up again. I sometimes shake the hose around, then it will come back on. If I try to dust with the dust brush (like a lamp shade or shelf) and the suction pulls against the object, the vacuum goes off for awhile. Sometimes I'll have to reset the vacuum by unplugging the electric cord. I never get to finis

Maybe you should have taken it back to that shop, it appartently isn't fixed. I would have replace that board, don't believe in modifing, you usually end up with other problems, like you have. One thing to check is maybe you have a partial clog in ... Vacuums

GE canister 106766 Power cord does not stay in bezel

Yes you are absolutely right.you would save on shipping cost if order both together.\015\012\015\012and for parts you can also order it from \015\012www.radioshack. ... GE 106766 Bagged Canister Vacuum

After fixing the pull cord on the poulan pro ppb30 /30cc backpack blower i can not get the cord to pull back in if i pull it. how do i get the correct tension on the recoil spring when i put it back together?

... Vacuums

I need a new power cord for the power nozzle on my Electrolux 2100 canister vacuum. The power nozzle has part number N115M written on the bottom. I have found the power cord for power nozzles PN6 and PN7 online, and it looks identical in photos but I'm not sure if it's the right part.

You can buy the hose at an authorized Aerus Electrolux store. If near enough, they will deliver, if too far, they can ship it. The nearest dealer can be found using the below link. Just follow the instructions.\015\012Just provide the model ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Miele vacuum Sometimes when I hit the auto roll up cord button or even move the cord, the power vacuum goes off. I move the cord again and it comes back on. I took it apart and looked at the connection from the cord to the auto roller. These are the electrical slip on type connections and are still in good shape. There are no bends in the cord. I air dusted everthing inside, put it together (with no extra parts!). Good news..it powered up so I did not break it, but it still has the same problem.

... Vacuums

Bosch canister vac BSG81313. Took cover off to remove lots of hair, dirt etc from running without bag in place. Everything went back together OK, but cord reel spring went zip when cover was removed. How do I rewind the spring so there is tension when the cord is pulled out ? Wound cord back onto reel, but reel just clicks ever revolution etc...no tension when cord is pulled out of vac. Bob

The spring inside the hub of the cord wheel has escaped from the locking tab. You must completely dismantle the vacuum to access the cord wheel - take it out, reattach the spring and reassemble the unit. All you need is a phillips screwdriver, a pai ... Vacuums

Power cord can not find replacement power cord for power brush attachment on kenmore canister vacuum, model #2491290 power brush attachment model # 5491290. i can not even find those model #'s anywhere online, not even partsdirect.com. any help would be great. thanks, david

Call 1-800-948-1358 ask for Buck mon.-fri. 9am-5pm est sat.9am-1pm est ... Vacuums

How do I remove the collar to replace the cord to the power bar, I have the part, cannot get the little collar off to connect the new wire, purple to white and white to black... cannot get the old wir

... Hoover Powermax S3530 Bagged Canister Vacuum

When taking the handle/wand back to use it seems to lose the suction power regardless of what setting I use. Upon several times of standing it back up it seems to engage the suction power correctly is there a button or something that does not always engage to get power? can I fix it

When you say taking handle back I assume you mean the action to start rotation of brushes. Had simular problem and found by removing brush from tube and then cleaning "baked on rubbish" in plastic tube (so you can see clearly through tube) Clean with ... Dyson DC28 Animal Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 2.4112 seconds