Having problems with your Electrolux Eureka Boss SmartVac Vacuum Cleaner 4870PZ ?

How do I change the hose on a Eureka the boss?


Answers :

Repair Help & Product Troubleshooting for Electrolux Eureka Boss SmartVac Vacuum Cleaner 4870PZ

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I change the hose on a Eureka the boss?


... Electrolux Eureka Boss SmartVac Vacuum Cleaner 4870PZ

Eureka Boss 12 amp Belt change - Eureka Mega Boss 4460DT Vacuum


... Eureka Mega Boss 4460DT Vacuum

Eureka Boss 2270 hose clogged - Eureka Boss 7601 Bagged Upright Vacuum


... Eureka Boss 7601 Bagged Upright Vacuum

Clogged hose on Eureka boss - Eureka Boss 7601 Bagged Upright Vacuum


... Eureka Boss 7601 Bagged Upright Vacuum

How do i Change the belt on the eureka boss 5893?


... Vacuums

I have the Eureka The Boss Power PLus Model # 4703 Type A. When using the detached hose and wand it works OK; however, when using the Vacuum with the hose attached it doesn't work well at all.


... Vacuums

How to change bag on eureka boss lite - Eureka 7618 Bagged Upright Vacuum


... Eureka 7618 Bagged Upright Vacuum

MY VACUUM ISN'T PULLING AS STRONG AS IT USED TO SO I THINK IT NEEDS A NEW BELT. I CAN'T FIND THE MANUEL ON IT SO I NEED SOME INSTRUCTIONS ON HOW TO CHANGE THE BELT. I DON'T WANT TO BREAK MY VAC. CAN SOME ONE PLEASE INSTRUCT ME ON HOW I SHOULD CHANGE THE BELT PLEASE. TYPE VAC: EUREKA THE BOSS WHIRLWIND LITE CYCLONIC POWER CANISTER TYPE VAC. THE HANDLE IS DETACHABLE TO CLEAN IN THE CORNER WITH A SMALL EXTENSION.


You can get Eureka replacement belts here:Eureka Vacuum Betls ... Vacuums

I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being


Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums

Something is stuck in my hose on the eureka boss smartvac, can i dtach plastic hose on side


Yes, there are a few screws that need to come out to do so, u can also use a coat hanger to loosen it up and turn it on, the vac will **** the loose dirt into the bag/canister ... Eureka Smartvac 4870 Bagged Upright Vacuum

How to change bag eureka victory - Eureka Mega Boss 4460DT Vacuum


... Eureka Mega Boss 4460DT Vacuum

Change belt eoreka mega boss - Eureka Mega Boss 4460DT Vacuum


... Eureka Mega Boss 4460DT Vacuum

How to change belt 4870MZ Eureka Smart Boss Vacuum


... Vacuums

Changeing belt how do you install a new belt? I have an Eureka, The Boss, bagless, upright. The brush is hardly rotating. I think it could be the belt but i cannot open the vacumm to check it. How can I fix this?


... Vacuums

Eureka the Boss Smart Vac. Hose has suction, but still isn't picking up. Weird.


Your belt is probably broken. Check your belt and make sure your brushroll has not seized. If both of those check out ok, (because the smartvac belt doesn't stretch,) the belt tensioner assembly may have gone bad. \015\012\015\012-R ... Eureka Vacuums

No suction power on my eureka boss vacuum (vacuum bag has been changed)?


Most probably a clog in the neck. This is where the power head connects to the body of the machine. Remove the base plate (screws in). Take a look at the back of the head behind the beater bar. There is likely something blocked in the nec ... Eureka Boss 7601 Bagged Upright Vacuum

Belt location i have a eureka upright the boss whirlwind lite and i need to change the belt. I have no clue where to find it. Need help with this


If you torn the macine over, at the bottom of the sweeper you will see the belt on on side. You have to take the bottom part apart and remove the brushes to replace the belt. I hope this helps. ... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum

How to change vacuum belt on Eureka the boss smart vac


... Eureka Vacuums

Eureka Boss is blowing hard out the hepa filter but no air in bag or suction from machine. No clogs found. Pulled all the hoses. Still nothing.


... Eureka Boss 7601 Bagged Upright Vacuum

I replaced the belt in our Eureka Boss Smart Vac, it still seems loose, it uses a type R belt. The beater belt still doesn't seem to turn properly and seems that it doesn't pick up very well when I use it on my berber carpet. We have 2 dogs and I like to use it frequently. I have changed the bags and belt......


Check to see that the beater brush is not frozen up. Pull the brush and clean it, spraying some WD40 on each end piece that holds the brush in place.\015\012Also be sure the belt is properly installed so that the brush turns in the correct direction ... Eureka Vacuums

I have a Eureka The Boss Smartvac. I was vacuuming and it just went off. It was on one second and then off the next. I changed the bag thinking it was full but it didn't go back on. What's happening?


If you also notice on the bottom left corner of the vacuum standing behind it you will see a small warning telling you about this and to let the system cool for 30 minutes prior to turning it back on. Make sure you clear everything during this time. ... Eureka Smartvac 4870 Bagged Upright Vacuum

No suction on my eureka boss smart vac. The belt is fine and the roller moves. I just changed the bag but no dice. any insight?


I know this is an old question but this is a good vac and maybe I can\012 help somebody else some day, wish I'd figured this out a couple months \012ago when this problem first started. :} Anywho, \012this is another option from an amateur; I don't ... Eureka Smartvac 4870 Bagged Upright Vacuum

Eureka boss 5856 vacuum cleaner is making a really loud noise. How do I change the belt. Do u think thats the reason why it's so loud ?


I have ben vacuum with my 5856 it has always worked great but today it just up and quit is there fuses or breaker that might cause this PLEASE HELP ... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

How do i change the belt on the eureka boss capture vacuum cleaner


Here is a link to the belts you need and a manual you can view which has instructions:Eureka Boss Capture Belt ... Vacuums

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o


I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0734 seconds