Having problems with your Electrolux Guardian Bagged Canister Vacuum ?

I jammed a deodorant cap into the entry hard plastic part of the hose. can I open that up to get it out?


Answers :

What goes into a vac hose enters the smallest part. The handle is designed to be a small reducer to prevent some blockage so the obstruction must back out. Do not attempt to use a sharp coathanger as you could tear the inside of t the hose and do not attempt to push the cover deeper as it will wedge tight. Your best bet is to draw this item back out with another vac. Sometimes bumping,( not smashing) the side of the handle against a carpeted floor area while doing so will help dislodge the item. Failing that you will need to open the handle itself.

If you look closely on this hose there are several small screw covers which will pop out with a pin to reveal hidden screws. Once removed the handle will open like a **** shell and then slide off the hose. The handle must be carefully aligned when reinstalling and the wire covers installed last, with the handle fully in place.
If all else fails and you must use a wire coat hanger, create a small 190 degree hook at the end so there is no chance of a sharp edge cutting the hose itself if pushed to far. Post back with results or if you need more help
Repair Help & Product Troubleshooting for Electrolux Guardian Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I jammed a deodorant cap into the entry hard plastic part of the hose. can I open that up to get it out?


What goes into a vac hose enters the smallest part. The handle is designed to be a small reducer to prevent some blockage so the obstruction must back out. Do not attempt to use a sharp coathanger as you could tear the inside of t the hose and do no ... Electrolux Guardian Bagged Canister Vacuum

I have the eureka bagless capture. The main hose is what I am interested in. I cracked the end of the hose where I would attach other parts such as the slim attachment for corners and to get inside the pillows in my chair, The part that I broke is on the very end of the hose. I had the plastic part clogged with some hair and during the process of getting it cleaned out, the part that I am speaking about is broken. Can you help me. I thank you, Mo moss


Change the hose part try a company called cds they r in the midlands but they courier parts\015\012out 2u dont have their no 2 hand u will need the model number try the\015\012web marting ... Eureka Uno 2998AZ Bagless Upright Vacuum

I have Optima, 12amp Eureka vacuum, Model 431, AXZ type and the extension hose for cleaning corners and edges --the plastic part that the attachments fit into has a piece broken off and tools don;t fit anymore. It looks like the hose attachment can be replaced--can it be and if so--where can I get a new hose attachment. It seems it is cheaply made of plastic and really shouldn't have broken a piece off.


... Eureka 431A Optima Bagless Upright Vacuum

Have Electrolux 1590 whole house vac, and can't see how to get brushes out. Leads so short, and don't want to break them trying to free brushes. Do they slide out of plastic housing? My eyes not real good, but it looks like the leads are part of a brass sleeve that slides into the plastic housing. It also looks like the plastic housing may be a snap lock type, but I don't see how to open it.


... Electrolux Vacuums

The plastic coupler that hooks onto the propane tank cracked. There is a replacement part, coupler, regulator, Y hoses to the main and side burner, avail but how do you disconnect and re connect them? The hoses have a clamped metal ban attaching them to the burner tubes can't get them off. Thermos Barbecue Model # 461410707 Thanks much.


Wrong forum to help you out. ... Vacuums

Shampoo-er This seems to be a common problem, the shampooer is putting out alot of water and hardly any suds. I read through the posts about the little filter that sometimes gets out of place and I think I found it in the box - is it about 1" diameter hard plastic ring around very fine mesh? If so where exactly does it go? Some posts say in the hose, and others say in the opening of the tank. Or does it go in the place where the hose attaches to the tray? I also found a round sponge in the box o


It goes on the small hole on the tank where the hose attaches to it. The sponge goes in the hole directly under the on/off valve. Here is a link to my online shampooer instructions.\015\012 \015\012 ... Kirby Ultimate G Bagged Upright Vacuum

I have a lawn sprinkler system that has a main inlet valve that opens when the sprinkler is run. This inlet valve failed after a recent long freeze when water retained in the valve became ice and then expanded. Questions: 1. Can I replace just the plastic parts that broke or do I have to replace the total valve? The valve is made by FEBCO,CA and the following is written on the valve: 4010387; 765-PUB; B 6412 and 150 MWWP. 2. Where can I get the valve or the parts? My zip code is 77479 and I ca


Yes you can, take the piece into home depot they can help with it. usually you can replace the total valve as awhole , its easier to do it this way, and still cost effective :) \015\012\015\012press add a comment in upper right corner if ... Vacuums

I'm using Miele Medivac vacuum and I just sucked in a small plastic eye drop container by accident(I sometimes take off the brush part to **** in 'small enough' articles). And it is jammed in the part where the plastic hose connector bends. I think I can take it out if I can just disconnect the long necked plastic hose connector that connects the metal wand part and the hose part. Is it designed to be disconnected or should I not even try it?


I love the fact that the filter bleeped out s.u.c.k ha ha! ... Vacuums

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.


... Vacuums

Broken black plastic of hose handle where it meets the metal part


You are going to have to contact the manufacture google the name and model # and serial # appliance parts places wont stock the specific part good luck . Tom ... Karcher K DS 5500 Vacuum

Model UH60010, Series X12.0, Mfg code K09A. While attempting to use the hose and the extensions to clean shelves, my wife reported no suction. I removed the brush roller and the plastic piece just below where the hose opening is located and saw a "flapper" door that was closed and had some debris sort of jamming it. I removed the debris, but the door requires extreme pressure to open to permit the dirt, etc to moved up thru the opening , through the hose, etc. I thught maybe that somehow tg


Hello,Check to make sure\015\012the dirt canister is empty. If dirt canister is full, then you will \015\012experience\015\012reduced suction. Empty dirt receptacle.\015\012 Could\015\012 be a clogged hose - ... Vacuums

Getting part My repair shop cannot get the part for my filter queen. It's the plug in the body of the machine that the short plug goes in from the hose. It's been bent. Can I get a replacement part?


Have you called your filter queen dealer? i used to be a rep. and we would fix problems at the office that i worked out of. hope this helps. ... Filter Queen Majestic Canister Vacuum

I just need the part number for my Guardian Electrolux model C134A i ran over the Hose and that was the part that broke. i need to compare prices so i can determine if it is cost effictive to change the switch or get a new hose


The part number for the hose is 47086.\015\012The best thing to do is contact the nearest Aerus Electrolux dealer. \015\012If it's just the switch or handle that broke, it will be more cost effective to have that replaced. If I remember ... Electrolux Guardian Bagged Canister Vacuum

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?


Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

Bissell 2x has suction coming out of the "base" part(when I put my had over the rubber ring that leads from base to the handle part there's suction), but there's no suction coming out of the hose. I'm not certain if there's a clog, 'cause I can't get the hose off.


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have an old Shop Vac model 3331.5. This is a 12 gallon 1.5 hight peak shop vac with a detachable blower. After many years I decided to use the blower feature, but have lost the lost the manual. Question; how do I attach the hoses to the blower? The motor has that cap on it the direct the flow of air in one direction and the wide hoses do not fit over it. I may be missing a part, but I would think the directional cap would have to come off anyway.


Remove the cap that directs the air and insert the hose in there. ... Vacuums

Help! i have a whispertone 300 model 116 28612790. the retractable cord is jammed & i could only get the front part of the canister open that houses the motor, etc. there are only 2 screws to open it & i can't get it off to fix the cord. hope this makes sense. thank you!


Even if you get it apart chances are it needs a new spring but it requires a special tool to get the rubber molding off that separates the top from bottom and sears repair guys and vacuum shops have them. I would take it to a used vac store and get t ... Kenmore 23313 Whispertone Bagged Canister Vacuum

I'm using a Eureka maxima 12 amp vacuum and where the hose is connected to the vacuum by a screw that part is broken where do I find a replacement hose that includes the clear plastic part that I can attatch to the vacuum?


... Eureka 4700A Maxima Bagless Upright Vacuum

Dyson DC 14 hose has no suction, with or without brush attachments. Hot air shoots out from the base of the canister when I try to use the hose. I cleaned the top filter, but can't figure out how to remove the hepa filter to clean it without destroying the case. It looks like it might take three hands to insert pennies and "flip" the case open as is suggested on a youtube video for a different model. Would this even help, assuming I could get the thing open?


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Clogged hose A makeup brush (about 3.5 inches long) was sucked up through the vacuum hose. It won't come back through the same way it came in because the bristles in the brush are expanded. We can see the brush on the side of the hose that connects to the canister but can't get it around the bend of the 360 part of the hose... is there any way to take the hose apart more?


... Kenmore 25512/ 25513 Progressive Canister Vacuum

On my Eureka Model 1759A (from mid-1980s), the plastic catch that holds the two parts of the metal body together has broken. I would like to replace the part of the catch that attaches to the top (the part with the lip on it), but I can't find the part online ... or even a drawing. Where can I get this part ? ? ? HELP ! ! !


This latch is riveted to the body. If you are lucky you may find an old Eureka warranty/ repair center with one on the shelf, or another canister for parts. That will be your best hope. ... Vacuums

Hi. Bought a M3888-3 Royalcylinder vacuum from Lidl. Lost manual that came with it. Only had it 4 mths. Need new hose. Plastic hose has snapped near whereit attaches to metal hose. Can I get a replacement hose from somewhere in U.K.? I know the vacuum is from Germany.


... Royal Vacuums

My dyson DC23 sucked up some plastic bags in the hose. How do I get them out?


... Dyson DC23 Bagless Canister Cyclonic Vacuum

Broken hose The hose on my Hoover F5837-900 Steam vac Supreme broke away from the coupler on the bottom of the unit - under/behind the recovery tank (solution tube is till attached). It might have gotten pinched in there a couple times. Problem - it was glued in the coupler really well, and I cannot get the whole thing out - hose will be too short anyway - is there a way to fix this or a part I can order instead??


You will have to replace the complete hose asm, part # 90001337 ... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

I want to install a new hose on a Sears vacuum Mod #116.23812300. How do I remove the Hose Connection Cover(#4370325)? It appears to be a flexible plastic part, however, it will not move from it's position on the old hose.


Hi,\015\012\015\012Please CLICK HERE \015\012This guide will explain you how to replace the hose.\015\012\015\012Goodluck.. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0964 seconds