Having problems with your Electrolux Guardian Bagged Canister Vacuum ?

Electolux power head screws

\015 I am trying to disassemble the powerhead to change the belt, but the two screws holding the top and bottom of the powerhead broke off and now I cannot get the screw stem out of the chamber holding it. Any ideas as how to remove them?\015

Answers :

Are all the other screws out?
Repair Help & Product Troubleshooting for Electrolux Guardian Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Electolux power head screws


Are all the other screws out? ... Electrolux Guardian Bagged Canister Vacuum

I have an electolux EL7001 canister vacuum. When I attach the large power nozzle....the one for the carpets not the small one for the floors...the nozzle is not powered unless I strap it on with duct tape. Is there some piece I can purchase that will secure the connection between the wand and the power nozzle head so that it is powered without the duct tape?thank you.


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

How does the Miele Vacuum Power Nozzle Pinion Gear get taken off and a new one put on? Is it pressed on and just need to pull off or is it screwed off. It is for the SEB217 power head


Greetings,\015\012\015\012What you need to do is screw the Pinion Gear off of the power brush. This can sometimes be tricking, because as I'm sure you're aware, when you twist the pinion gear to try and release it, it also spins the mot ... Miele S318 Bagged Canister Vacuum

How can you take the top of a rainbow D-4 series to repalce the plug for the power head? I can't find any screws to take out


This is a time consuming jod. You will need to carefully peel back thew rubber gasket around the separator . Underneath you will find several hidden screws.Loosen them off. With the separator removed you will be able to loosen the upper body and moto ... Vacuums

How to disassemble the power head of Kenmore vacuum, model 11652450203C . Tried with screwdriver but is there a screw somewhere inside that I'm missing


... Vacuums

I have an Electolux Oxygen canister vacuum and the power head suddenly stopped working. It is only a few months old. Any suggestions.


1. You have to verify if it's simply the belt that has broken and the spinning brush isn't spinning because of it. Place your ear next to the top of the power head to listen for the power head motor. If electricity is getting to the head you'll hear ... Electrolux Oxygen Z5540 Pet Lover Vacuum

Sears 116.31913 Lower units, vacuum motor and agitator power head do not have power/115v to them and won't run. I'm trying to take the handle apart to access the on off switch. I've taken all observable screws out and cannot separate the handle and section immediatly below the handle to access the on/off switch, to trouble shoot. Any tips for separating the plactic pieces enclosing the on/off switch?


... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Power head and wand connection is intermittent.


If there is a rubber bumper on your power head you must slip it off before the two halves will separate. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

The motor on my Epic 6500 works, the hose is sucking, but the power head isn;t working... I tried the sidestep power head and that one works. Ive opened and replaced the belt and that is fine. The bulb was already burned out and wasn't replaced so I cant tell if theres power to the head. What else could it be?


Connect the power nozzle directly to the hose and try.\015\012Check the terminals where the wand connects to the PN. If any are discolored or cracked, that may be the problem.\015\012Open the PN and check for loose or broken wires and co ... Electrolux Epic 6500 Vacuum

Power head attachment works great when plugged into the hose part of the vacuum. The problem is when I attach it to the tube for normal use there is no power. I have checked all the connections and switched the power switch on and off still no power from tube to power head. Is there anything else I can try? Model Callisto


Try having someone turn the machine on and off while you pull the cord in and out with the cord more angled towards the on/off switch. Sometimes these models have a break in the cord rewind and will not put the power through to the motor. ... Miele Vacuums

E series power head handle, internal wire came lose


Here is a pix.\015\012\015\012 ... Rainbow E series Canister Wet/Dry Vacuum

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin


... Vacuums

Our Electrolux canister vacuum just stopped working when we were vacuuming the floor. The power does come on when the power head is attached but as soon as the power head is removed the power shuts off. I tried pressing the reset button but that doesn't help. Is there a solution that I can try at home?


Sound like you problem is in the connection going to the power head you will see a small screw on the power nozzel where it joins to the handle take out the screw and take it a part you will see where one of the bars have been disconnect from the pow ... Electrolux Guardian Bagged Canister Vacuum

Miele Blue moon vacuum motor surging on and off and power light flashing. After many surges of the motor (on->off->on-> off etc), the motor no longer attempting to start as ferquently ie. now off for many seconds and may turn on for 1 second.. sometimes stops turming on and just power light flashes. There is also no voltage at the plug for the hose for the power head. I noticed that the vacuum first started having probs when hair was caught in the power head and the ovetrheating light went on


... Miele Blue Moon Bagged Canister Vacuum

I have a tank style vacuum. When I vacuum with the power head it dims and slows down when I push the power head back and forth, but it powers back up louder when I stop pushing it If i remove the powerhead from the hose the vacuum works fine.


Most likely the belt. Thats the cheapest so try it first ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos


It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

Electrolux Epic 6500 Power head


Call your local Aerus repair shop. ... Vacuums

Power head has power but motor won't run


Circuit brealer switch may be bad, but the fact that Rainbow nozzle made this strange sound makes me think that it may have ha ... Rainbow E series Canister Wet/Dry Vacuum

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!


Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

I have had my Fantom Lightning vacuum for about 12 years and the power head motor has burnt out. I would like to know how to purchase a new power head as I just love my Fantom. How much are they and can I still buy one?


There are no parts \015\012you can try and find used one\015\012if your in my area i have a used one in stock ... Fantom Vacums Lighting Canister Vacuum

The power head on my kenmore 22822 Canister Vacuum won't work? the power upholstery head works fine.


I have the kenmore whisper belt and i have a reset button on mine ... Kenmore 22822 Canister Vacuum

I have an S3630 Hoover Windtunnel with a Mach 6.1 power head. One of the wheels on the back of the power head broke off. I will need the back under pannel with the back wheels. Where can I get these parts?


... Vacuums

The power head keeps shorting out during use. one of the connecting prongs from the handle to the power head is black instead of silver and is smaller in diameter like it has been arcing inside the connection. could this be the problem and if so can I replace it or will I have to take it to a repair facility. Thank you for your help, Jim Carey [email protected]


This is a problem with the connection in the wands and the powerhead. Because they are shorting out you may have to replace the neck on the power nozzle. (Leave that to a pro). But you will definatly have to purchase a new wand as replacement wires a ... Electrolux Lux 7000 Bagged Canister Vacuum

Power head motor is good,runs great from test cord switch seems to work. brush roll cleaned but power head motor will not run


If you have checked the power delivery down to the powerhead and you have current running to the powerhead, then you likely have a burned fuse. There is a fuse built into the powerhead motor and is usually located on the field winding. This is not ea ... Eureka 6831A Bagged Canister Vacuum

The Dyson DC21 power head keeps tripping out. The carpets in the house are medium to low pile. It even trips out over hard surfaces. Could it be the resistor in the power head is to weak or faulty.


... Dyson DC21 Bagless Canister Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0356 seconds