Having problems with your Electrolux Harmony Canister Vacuum - EL6985 Vacuum ?

Can't get dustbag to fit

\015 ELECTROLUX HARMONY CANNISTER VACUUM CLEANER STYLE OX.\015\012CAN'T FIT DUSTBAG ONTO HOSE\015

Answers :

The dust bag doesnt fit into hose your supposed to out ur bag into the plastic bag holkder then sit inside the canister and this model does not take an ox bag it takes an s bag y
Repair Help & Product Troubleshooting for Electrolux Harmony Canister Vacuum - EL6985 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have been given a SF-AAC 50 Miele filter which I was told fitted my Revolution 700 cleaner but I am very frustrated as I cant get it to fit please help


That is the wrong filter - the 50 series only fits Miele S4000 and S5000 models.\015\012\015\012The filter you need for the 700 is the Miele SF-AAC-30\015\012\015\012As seen here:\015\012\015\012http://www.miele.co.uk/accessories/De ... Vacuums

Can't get dustbag to fit


The dust bag doesnt fit into hose your supposed to out ur bag into the plastic bag holkder then sit inside the canister and this model does not take an ox bag it takes an s bag y ... Electrolux Harmony Canister Vacuum - EL6985 Vacuum

Rented triumph 430 and cant figure out how to work the accessories. I have the vac hose and a smaller hose attached ro dispense solution. There appears to be no way to plug in the smaller clear hose. Was I supposed to get another length of hose to connect from fitting on accessory to machine?


Yes don. call the store where u rented and tell them. ... Vacuums

I cant get the brush to fit back into my roomba


I had the same problem, but I cleaned out the hello brush bearing on the end and was able to fit the brushes back in. Apparently, enough little hairs got underneath it to push it out. This video shows you how to clean the brushes and shows you how ... Roomba Robotic Floor Bagless Vacuum

CANT GET MY POWERSTEAMER PRO DELUXE MODEL 8804 BACK TOGETHER


Http://newzealand.bissell.com/images/IncludeContent/Service_Center_Help/Upright_Deep_Cleaner_Repai ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

The belt wont turn...i cant get in to the inside to check to see if the belt isnt on the roller...how do i get up in there..i took the bottom plate off and you still cant get inside... thx Peggy


The following site has some great info on your machine:\015\012\015\012www.dysonmedic.com ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a morphy richards upright hoover model 7333 and i cant get to the belt to see if it is either broken or just come off the runners, i have lost my instructions and cant get the things apart to have a look, does anyone know anything about these hoovers? many thanks, Carina.


... Hoover Vacuums

How do i take the old belt off of my dyson dc 14? cant seem to figure out how to get the roller separated from the machine because i cant get the old belt off.


Go to: Dyson web site or \015\012\015\012 http://www.repairclinic.com/0100_24.asp\015\012\015\012There should be 4 to six screws holding the ... Vacuums

I HAVE A DC33 BRAND NEW DYSON I EMPTIED TO CANISTER AND NOW CAN NOT GET IT BACK ON FOR A GOOD FIT TO GET SUCTION


... Dyson DC33 Multi-Floor Upright Bagless Vacuum Cleaner

I have a samsung galaxy europa, i get repeated messages 100s of times (no exagerating) i cant get a replacement as i have had the phone unblocked, it was happening before i got it unblocked too, is there any was of getting it fixd?


Glad im not the only one i have the same problem with mine but it just seems to be o2 numbers, i have taken it back to the shop, and they i have changed the sim card about 3 times and they sent it off to samsung and they apperantly changed the handse ... Galaxy Vacuums

What hose gets hooked up for upholstery cleaner. The one that usually goes in front? I cant get my vacumn to turn on.


Hi!You need to take the power nozzle off and attach the thing that looks like a little plastic "cup" with two hooks and a screen on it. This is the intake guard. Attach it to the front. Now remove the cloth bag and put the hose on the hole wher ... Kirby Ultimate G Bagged Upright Vacuum

There is a clog in clear tube that sends trash from floor to cylinder. have pulled out lots but cant get really far in there. can I take the hose off somehow and get in there


Try using a hanger and see if you can snake it out there might be a small hose on bottom of power head,i hope this helps thanks ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

I have Optima, 12amp Eureka vacuum, Model 431, AXZ type and the extension hose for cleaning corners and edges --the plastic part that the attachments fit into has a piece broken off and tools don;t fit anymore. It looks like the hose attachment can be replaced--can it be and if so--where can I get a new hose attachment. It seems it is cheaply made of plastic and really shouldn't have broken a piece off.


... Eureka 431A Optima Bagless Upright Vacuum

I am trying to replace the cable and actuator on a Hoover windtunnel self propelled vacuum. but I cant get the top or hood off the get to them, I have removed all the screws I can see, roller, belts..what am I missing?? thanks so much for any help


Hi there SmartAlec from NelsonVacuums.com.au here. You will need to remove the knobs for carpet/hard floor selection and the carpet height to remove the cover they act as k ... Vacuums

I have a rainbow vacuum and it just quit cant figure out how to get to switch to see if it is getting power


Follow the cord up into the vacum it;s probably in the arm. ... Vacuums

There is a break in the cord where the clamp is entering the unit of our Majestic IAQS system Filterqueen Lux have tried to get into it but cant seem to get it open! Any ideas?? This unit is approximately 5 years oldish!


Undo the side clamps so that you can get to the dirt below. Grab the handle and remove the top portion of the canister. Take the top portion and to go the table. Remove all the attachments (if they are even attached). twist an ... Filter Queen Majestic Canister Vacuum

I've recently bought a hitachi HDR505 & haven't had a problem using it with an indoor ariel other than the fact in bad weather conditions there have been problems with the signals. So I tried to attach the ariel wire that connects from a box in the corner of my living room which connects to the outdoor ariel but cannot connect it into the 'ariel in' compartment on the box as it does not fit into that hole but does fit into the 'ariel out' hole. Please could I get help with a solution asap as I w


... Hitachi Vacuums

I have a handheld steam cleaner model mc1220 and i cant get the lid open .what can i do to get it to open.thank you.


... McCulloch MC1275 Steam Vacuum

How do you put the telescopic wand down? Just got a new dyson 17 and I cant use it cause I cant get the dang wand down..


Make sure your handle is snapped in all the way on to the machine, that will release the clip on the hose to allow for the wand to slide in. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I NEED A TELESCOPIC HOSE FOR MY PHILIPS EXPRESSION HOOVER, WHERE CAN I GET THIS MY HOSE PIPE IS BROKEN AND I HAVE TRIED TO GET A NEW ONE AT VARIOUS SHOPS HERE IN IRELAND AND I CANT.


Hi - greetings from Scotland!\015\012Im not sure if you mean telescopic hose = do you mean telescopic metal tubes? If so they are readily available on ebay.co.uk I buy from many sellers on there but Hoovermania are one of the best. \015\012\015 ... Philips Vacuums

Manual issues Have reciently purchased a kirby from ebay (gotta love ebay) but has no manual. I believe the model is a heritage (cant see a II though) Do they all have roughly the same manuals??? I have all the attactments - spray painter, hair trimmer, turbo brush etc but really want to get the most from the machine. Where do I get manuals for machines that are 20yo???!!!


Many years ago I was a service engineer for these machines in England they were actually made by a company called Scott &Fetzer in the USA and Branded KIRBY or CIMEX.\015\012\015\012See if Scott &Fetzer are still around and ask th ... Kirby Heritage II Vacuum

I'm trying to use the reverse flow hole on my Miele s712 to blow up an air mattres. None of my fitting appear to fit so I can use the hose. Is there something I'm missing? Is there a trick of the trade? Or am i missing some gear. It's new, out of the box but I just can't get the hose onto the reverse flow. The Poduct is a Miele S712 vacuum dispite what this system has allowed me to enter. ; )


I GO THROU INSTRUCTION BOOKE OF SERIES 700 I DO NOT FOUND THIS REVERSE FLOW......THANKS ... Miele S548 Bagged Canister Vacuum

I HAVE LOST MY INSTRUCTION BOOK FOR THE STEAM VAC SPIN AND SCRUB. I WANT TO USE THE STAIR ATTACHMENT, BUT I CAN'T FIGURE OUT HOW TO HOOK IT UP, OR OPERATE IT. I SEE WHERE THE PLUG IN PART GOES IN THE FRONT OF THE MACHINE, BUT I CAN'T GET THE OTHER PART TO SLIDE INTO PLACE ON THE FRONT OF THE RESOVIOR TANK AFTER I REMOVE THE FRONT PANEL, AS THE DIRECTIONS ON THE FRONT OF THE RECOVERY TANK SAY TO DO. THE FIT IS JUST TOO TIGHT. WHAT AM I DON'T WRONG- OR HOW COULD I GET A REPLACEMENT INSTRUCTION BOO


You can download a PDF version of the manual at the link below. I believe you can contact Hoover as well and they might mail you one.http://www.hoover.com/CustomerService/Manuals/Default.aspxGood Luck! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Cant get the belt to pick up on the hook when trying to get the head attachment working


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=844275\015\012Generic problem for all Vacuums\015\012Can’t get the belt to\015\012Posted by jltbo ... Vacuums

On my Kenmore whispertone 5.1 the bearings are bad on the motor there are two bearings they are listed as 608 BRS I see bearings all over ebay 6082RS 608SS but none BRS can I use any 608 Bearing or does it have to be a 608 BRS Bearing are these dry bearings or greased bearings I cant get any real information on the bearings I dont want to go to sears when I can get bearing much cheaper off ebay can some one shed some light on the bearings I would use the motor is made by Lamb Ametek went to ther


... Kenmore Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0616 seconds