Having problems with your Electrolux Lux 5500 Canister Vacuum ?

Electrolux 5500 The cord on my vacuum cleaner won't retrack. What is the trick to get the back end off the vacuum cleaner? It looks like it was pulled out too far.


Answers :

Depends on which model you have, but most of them you take off the center section, then you cab get to the 2 screws on top , and there is a screw on the bottom, then the back end will pull off. But I wouldn't try taking the cord reel apart, if that spring lets go while you are doing that, it could be dangerous. Also make sure that it isn't plugged in.
Your local Aerus representative can fix that for you really cheap.... Especially compared to if it gets broke, that could be more to fix than if you bought a new machine.
Repair Help & Product Troubleshooting for Electrolux Lux 5500 Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Electrolux 5500 The cord on my vacuum cleaner won't retrack. What is the trick to get the back end off the vacuum cleaner? It looks like it was pulled out too far.


Depends on which model you have, but most of them you take off the center section, then you cab get to the 2 screws on top , and there is a screw on the bottom, then the back end will pull off. But I wouldn't try taking the cord reel apart, if that ... Electrolux Lux 5500 Canister Vacuum

I have an Air Track plus vacuum cleaner and something has got stuck between the flexible part of the hose and the solid black section at the end. I tried to put a coin down to clear it but that has got stuck too. It looks like the rigid section should come apart (a small notch each side) but I can't figure how to do this.


... Samsung Vacuums

Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.


Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums

Hi. We have a Riccar N2100 vacuum cleaner, which has served us well for many, many years. I'd like to attempt a repair on this unit, and looking for advice and/or a parts diagram to proceed. The unit makes a groaning sound when shut off. The sound tapers off in pitch as the motor and beater bar come to a stop. The sound only happens when the vacuum cleaner is turned off in the normal upright position. The sound does not happen when the lower unit and main housing are both laying flat. I took


... Vacuums

Shampoo attachments... I have all these attachments for my vacuum but never needed to use them. It was my mom's vacuum and she can't find the manual so I'm in a rut and my rug looks like a herd of elephants have been all over it (the rug is also my mom's) so it really needs washed. Can someone please walk me through the necessary steps to get this thing turned into a super duper carpet cleaner? Thanks.


We have manual with plenty of pictures HERE.Good Luck ... Kirby G5 Bagged Upright Vacuum

I have a Bissell Model 8905 Carpet Cleaner. I was going to replace the belts because the pump belt broke, but when I turned the machine over, a small piece fell out. It looks like a tensioner arm because it has a small round part at each end on opposite sides of an arm that has an offset or "dogleg" in it. I am looking for an exploded parts diagram to determine what the part is and where it came from.


... Bissell 8910 ProHeat Clear View Upright Vacuum

I need a replacement belt for a V1315 Shark Roadster Vacuum cleaner. Looks like there's no way to get one. Is there a compatible belt that will fit this vacuum?


... Euro-Pro Roadster V1315 Upright Vacuum

I have an old Progressive vacuum cleaner that says "Hepa Filter" and "Whisper Belt". Not sure what the model # is. The problem is that the vacuum part itself (the part that touches the floor and rolls over) has ejected its filter that we can see through the little window- it just came out under the rollers under the device... we cannot see how to re-insert this piece of filter which looks like a kind of round, flat grey foam/fabric and clearly goes inside- (top of the part that touches the flo


Check this procedure:\015\012\015\012Unplug the appliance that you will be \015\012changing the filter in.\015\012\011\011\011\011\011\011\011\015\012\015\012\011\011\011\011\011\011\011\011\015\ ... Kenmore 23313 Whispertone Bagged Canister Vacuum

I HAVE A FANTOM VACUUM CLEANER MOD.#F1205400. I PURCHASED IT ABOUT 6 OR SO YEARS AGO.IT WORKS PERFECT,AS FAR AS SUCTION, THE ONLY PROBLEM IS ABOUT 2 MONTHS AGO,SOMETHING HAPPENED TO IT AND IT GOT VERY LOUD, KIND OF LIKE A CAR WITHOUT MUFFLER. I TOOK IT APART,AND FOUND NOTHING OBVIOUS. CAN YOU GIVE ME SOME IDEA OF WHAT I CAN CHECK TO RESOLVE THIS PROBLEM. AS I SAID BEFORE IT STILL VACUUMS GREAT. THANK YOU, VINCE


You probably have a bad motor bearing. I don't know if the motor is available now or, these older Fantom's are obsolete along with most of their parts. ... Vacuums

The belt on my used Eureka Boss 5857 upright slips off the end of the motor shaft every time the vacuum is used. When I turn the brush roll slowly by hand, the belt walks toward the end of the shaft. It looks like there was a plastic projection from the base that snapped off, and maybe that plastic piece used to block the belt from falling off. Do I need to try to reconstruct that plastic piece, or is something else wrong?


... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

Windtunnel Hello: I was reading thru another readers problem of power to vacuum but won't turn on. Same problem for me. All hoses are free of clogs and I have the vacuum basically taken apart as far as I can. You state a THERMO by the motor may be open. What does this part look like? Thank you. Craig


The thermo is a small square piece with two wires coming out of it. Did you check the switch? The switch has a high failure rate. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hello, I have a Kenmore Progressive Canister Vacuum 116.20912006. It won't turn on. On the hose assembly, the end where the hose swivel is, there are 4 metal pins that plug into the canister. One of the pins looks like it broke off. There are only three pins remaining. I assume there should be four pins as there are four holes. Is this the problem and is it fixable? The vacuum is from 2002 so I am not sure a replacement part is even available and at what price. Thank you. Susan susan.eng@


Hi Susan, if the pin has broken off you can do one of two things, first, would be to find a local vacuum repair shop and take it there for them to look at. they may be able to look at the hose and fix it for you pretty cheaply. what ... Kenmore Progressive 20912 Bagged Canister Vacuum

I have a cannister (Animal something...) Today, it didn't sound right - like a blockage. I took out the filter - seemed OK; I looked for a blockage - found none. I continued to vacuum, but it wasn't picking up. Then, I stopped again, and I found a blockage (cat toy mouse) right at the end of the hose (attachment end.) I cleared, and I turned back on - nothing. Completely dead. It is one year old, just about exactly. Desperate, Sharon Tracy


Hello,if your canister is completely dead, then it means its having a power problem. You need to focus your attention on that part of your canister that relates to power. Such as; power wire, if you don see any fault with the power cord, ... Dyson Vacuums

Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and


The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I own a Miele S5210 vacuum cleaner which has stopped working. It looks like the dust bag wasn't fitted properly and the machine is very dirty and the filters are completely clogged. I've cleaned it up as best I can and have replaced the filters but it still won't operate. How can I get inside the casing to clean the inner motor compartment? Thanks Tom


... Vacuums

My Kenmore 7520 canister vacuum has a problem with the retractable cord. It has jammed and does not come out or retract. It jammed half way through the retracting action. Cannot pull it out or retract. Would like to know how to open the canister to take a look for the problem. Thank you


... Vacuums

I have a Panasonic MCE6003 vacuum cleaner. I regretfully leant it to a neighbour and it came back full of dog hair and keeps cutting out. I cleaned out the dust container and the main filter but it still kept cutting out after 5 minutes. I decided to unscrew the part with the motor and wash the filter inside.It was all going well until a large rubber washer bit, a piece that looks like the thermostat and a little white button attached to two black wires fell out and now I have no idea how to put


... Panasonic Vacuums

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.


... Vacuums

Miele S5000 (revolution 5000) vacuum cleaner - How do I open the casing? When the power button on the handle is pressed the green power-level lights on the handle light, but the motor sounds like it gives a little 'jump' but nothing more. The orange power light on the body also dims. I assume the motor or fan is jammed, but I can't open the body to find out. I've taken out to screws inside near either end of the handle, but to no apparent effect. I'm assuming the body is held together by plastic


... Vacuums

Which Kenmore vacuum cleaners are made by Panasonic? Are all of their direct drive machines made by Panasonic? We have a blue Hoover Windtunnel with the dirt sensor. It cleans well, but it is unbelievably noisy. I wondered if something was out of place and the brushes were hitting, but everything looks normal. We bought Kenmore models 36722 and 36724 and love them. I believe they were made by Panasonic. Our Kirby sits in the basement. Much heavier. These are quiet and clean well. I would like an


Some Kenmore vacuums are made by Panasonic, some are made by Hoover or Eureka or even Sebo. I would go to a Panasonic dealer for that kind of machine instead of trying to go by the Kenmore brand. Sears has a hard time with service. A good Vacuum C ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Dyson DC07 I actually need to locate and replace the brush as it split on one end. Looks like I need to pull the belt off to do that. Might as well replace the belt while I'm at it.


Hi.\015\012\015\012Depending on wether your machine has A clutch fitted will decide how easy this job will be.\015\012\015\012The non clutched model is very simple turn the 3 plastic screws on sole plate to unlock position lif ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Our meile vacuum has a short in the power cord - i think my son pulled it out too far. How do I take it apart to look at the base of the cord?


A how to take this vacuum has been posted here\015\012\015\012Good luck! ... Miele S318 Bagged Canister Vacuum

I have a philips FC9222 vacuum cleaner. When i switched it on today all the lights came on but the motor did not start. all the lights are on and you cant adjust the power up or dow n using the button on the top. the whole thing just looks like it has frozen on. i would be grateful if anyone can help. thank you.


... Vacuums

My recovery unit appears to smoke when pulling a vacuum It is some kind of condisation coming from the top of the pump. It has never done this before. What is the couse. Looks like smoke but isnt.


... Mastercool 69788 Recovery/Recycle/Recharge AC Recycler System

Dead motor? My 8 year old Miele S251i has worked fine, until I was recently vacuuming and moved the plug from one outlet to another. When I restarted the vacuum, it made rrrrr.....rrrrrr....rrrrr noises and smelled like something was burning. I turned it off, and it's shown no signs of life since. Sound like a motor problem? I've taken the cover off and looked at the cord and seen the motor, nothing looks obviously wrong, but I'm also not mechanical.


... Miele S251 Flamenco II Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0941 seconds