Having problems with your Electrolux Lux 5500 Canister Vacuum ?

My electrolux canister model keeps shutting off after a few minutes use. can reset by unplugging and replugging, or by opening and closing access door


Answers :

Repair Help & Product Troubleshooting for Electrolux Lux 5500 Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My electrolux canister model keeps shutting off after a few minutes use. can reset by unplugging and replugging, or by opening and closing access door


... Electrolux Lux 5500 Canister Vacuum

GE Spacemaker Microwave PVM1870 fan keeps running after door closed and won't shut off. Have to open door or unplug. As soon as door is closed and plug is back in, fan starts up. If door handle is pressed downward, microwave starts! If door handle is raised, fan shuts off but light stays on.


... Vacuums

I have a Liftmaster garage door opener and the garage door faces south. Normally the opener works great except at certain times on a sunny day.The sunlight is not directly hitting one of the sensors but the door will comedown as far as half way and then it will go back up and the lights will flash. If I go inside and use the button I can hold it down until the door is fully closed. However, sure is a pain to have to take the car out, go back into the garage, shut the door and then leave the h


Sounds like a problem with a limit switch or something getting in the way of the electric eye that interrupts for safety reasons. \015\012Clean the electric eye transmitter and sensor of debris and cobwebs and make sure the wires are attached properl ... Vacuums

Model UH60010, Series X12.0, Mfg code K09A. While attempting to use the hose and the extensions to clean shelves, my wife reported no suction. I removed the brush roller and the plastic piece just below where the hose opening is located and saw a "flapper" door that was closed and had some debris sort of jamming it. I removed the debris, but the door requires extreme pressure to open to permit the dirt, etc to moved up thru the opening , through the hose, etc. I thught maybe that somehow tg


Hello,Check to make sure\015\012the dirt canister is empty. If dirt canister is full, then you will \015\012experience\015\012reduced suction. Empty dirt receptacle.\015\012 Could\015\012 be a clogged hose - ... Vacuums

After a brief power outage my Marantec 4700 garage door opener has problems opening/closing. When opening it stops at the fully open position and the lights blink, when closing it automatically reverses just as it fully closes and then the lights start to blink again. I checked for obstructions and tried to reset the limits of travel per the manual, it still does the same thing. Any ideas on what to try next?


This is not a sensor issue, I have a similar problem, sensors work fine, garage door is still fully functional, all operations, including safety sensors work properly, just the overhead lights flash. I suspect there was damage to the power board due ... Vacuums

I have a Chamberlain Liftmaster Professional 1/3 hp garage door opener. I'm unable to find the model number, but it was made in April 2004 and has an orange learn button. It has been working fine since it was new, but now will not open or close when the code is entered on the touch pad. When the problem first started the door would close, but not open. I have tried to reprogram a new digital code, but it does not work at all. There are no problems when opening or closing the door with the re


... Vacuums

I have an older Blue Max screwdrive. No safety beam on this model. The door will not close with the remote or wired switch. Press = door opens. press = nothing. press = door opens. press = nothing. With latch lever pulled door will open and close easily.


... Genie Company Vacuums

My electrolux oxygen canister cuts on and off. I have to open and close the vacuum, or take the base of the hose off and then re-insert. I have to do all these things before it will start up again. I sometimes shake the hose around, then it will come back on. If I try to dust with the dust brush (like a lamp shade or shelf) and the suction pulls against the object, the vacuum goes off for awhile. Sometimes I'll have to reset the vacuum by unplugging the electric cord. I never get to finis


Maybe you should have taken it back to that shop, it appartently isn't fixed. I would have replace that board, don't believe in modifing, you usually end up with other problems, like you have. One thing to check is maybe you have a partial clog in ... Vacuums

Kenmore Microwave Hood Combination Model #721.80839500 The microwave will not turn off. Even if we unplug to reset it, once we plug it back and close the door it runs constantly.


... Vacuums

My brand-new Hoover Windtunnel T-Series Pet Rewind Bagless vac simply shut off while I was using it and now I can't get it to turn back on. I've emptied the dirt collection bin and let the unit sit unplugged for 30 minutes to reset the Thermal Protector as per the manual. I've even tried a few different outlets just in case a fuse got tripped, but the vac still won't turn on. What happened? Do I need to return this vac to the store? I just bought it 5 hours ago.


... Hoover Vacuums

My garage door opener will start to close then stop and go back to the open position. If I put pressure on the door as it is closing sometimes it will close all the way and sometimes it will return to the open position. Can you help me. Thanks


Sounds like the pressure sensor is being tripped - this is a safety feature on most makes in the last 10 years.Find the make/model of your device and it probably has some knobs on the main unit to adjust. For example, on the ... Vacuums

I have a craftsman garage door opener remote control model TX2028 139.18191. The remote stopped opening or closing the garage door. I replaced the battery and tried to re-program it through the LEARN button as per the manual of the Garage 1/2 HP opener. The process has failed after several trials and the remote is still not working. Is there anything else that I can try or should I get a new remote. Thank you


... Vacuums

I hit the button and just the light comes on,then i hit the button again and the door closes almost all the way but opens and light keeps flashing . the sensors are on and clear of obstructions . it is a wayne dalton quantum 3212 garage door opener.


Hello ccap..... It sounds like one of those sensors has gotten out of alignment with the other. check to see if there is a steady green light on each sensor. If not, adjust until the light is a steady green. Joe\015\012\015\012Thanks ... Vacuums

I shorted out the light socket on my Chamberlain Professional Garage Door opener. Now it wont open, I am looking for a fuse or reset button, but cant find one. Is there a way to reset it or did I fry the solinoid


First check your house fuse. ... Vacuums

I have a genie screw type garage-door opener. the fuse blew on the moter drive board , now the door only opens when you push the light button on the wall console ,will not go closed.green light blinks continually. when I power it up it jumps closed then nothing. It seems like the motor is not reversing.


... Genie Company Vacuums

I have Pro Safe PSF80 and everytime I enter my password, the lights are blinking and can't open the safe. Since the only way to reset my password is when the door opens, I cna't reset it either. I need yuor help, how to fix this problem.


2 blows with a pickaxe on the hinge and it was open in less than 1 minute ... Vacuums

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced


There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

I have a 1/2hp master mechanic door opener. when I close the door it goes the full travel down and then opens back up. i checked the eyes and everything was lined up. do you have any suggestions?


Look at the setting for "fully closed". it sounds like yours is set for slightly than the actual opening....So, the door reaches that location, and it thinks it hit an obstruction, which causes the door to open....While you are there, reset the sensi ... Vacuums

My e wave microwave appears to be in fine working order until the door is opened. It then trips the breaker and ceases working. Ater the house breaker is reset, the power is restored to the microwave until the door is opened again.. I havve tried plugging the microwave into another area that is on a different power breaker but again the breaker trips and the microwave ends all functions. Have you any solutions to my problem? Email Address [email protected]


You may have a short circuit on the INTERIOR LIGHT BULB circuit in your microwave.\015\012\015\012This might explain why the breaker trips every time you open the door.\015\012\015\012If so, you would have to unplug and disass ... Vacuums

My Dyson DC14 Animal doesn't have the suction it used to. The piece in the back on the bottom - a flap it appears - stays open now, causing the machine to make a louder noise than usual. At first, if I put my hand on the flap opening it would close, allowing for normal suction. Now, it stays "open" permanently", causing the loss of suction.


Hi its Darran at Dyson.Having had a look at a DC14 here, I am unsure as to the part you are referring to. So that we can help you further, please contact our Helpline free on 0800 298 0298, between the hours of 7am - 10pm, 7 days a week. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Have a hoover windtunnel platinum. I have changed the bag ( hepa Q bag) but the bag light wont reset. so the vaccum wont turn on. I have unpluged it and let it set for a while with the new bag in and repluged it in. I have checked the brushes and it is all clean but it will not reset. This only the second bag so it is a new machine I should not be having problems. Is there some sore of reset button I can hit.


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

I have a hoover windtunnel platinum. I have changed the bag ( hepa Q bag) but the bag light wont reset. so the vaccum wont turn on. I have unpluged it and let it set for a while with the new bag in and repluged it in. I have checked the brushes and it is all clean but it will not reset. This only the second bag so it is a new machine I should not be having problems. Is there some sore of reset button I can hit.


... Hoover Company Wind Tunnel U53019 Upright Vacuum

I purchased an Emerson smartset alarm clock I had to unplug and replug Unfortunately, I can't get the time reset properly It keeps resetting iteself........to the worng time I can't find what i did with the original instructions Where can I get a duplicate manual or instructions to correct?


Scroll through this list the duel alarm with smart set will probably be simiular. Good luck. http://portablem ... Emerson Vacuums

I own a stanley model 7100 garage door and the light does not come on or off when the garage door is open or closing


Hello. Begin by changing the bulb. Get a new bulb which is vibration proof. J. ... Vacuums

I opened the cannister to change the bag and when I closed it the motor switch will not turn on. The second position which turns on the attachment for rugs still comes on. We thougth it was the switch so we ordered the part and it is still doing the same thing. Is there a reset button somewhere inside? The only reset button I see is on the attachment which is working.


It can be a few things. First check the overload protector located on top of the canister. If it has tripped the unit will not run. Push it in to reset. \015\012If that is the problem check the motor safety filter to see if it is clogged and caused t ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0624 seconds