Having problems with your Electrolux Lux 5500 Canister Vacuum ?

I have a model 1521 electolux canister vacuum and have replaced the motor but forgot the wire locations can any one make me a simple diagram


Answers :

Repair Help & Product Troubleshooting for Electrolux Lux 5500 Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a model 1521 electolux canister vacuum and have replaced the motor but forgot the wire locations can any one make me a simple diagram


... Electrolux Lux 5500 Canister Vacuum

Hello, I am looking for a wiring diagram to install a touch/dimmer switch by "Comfort" mdl # RH-934B - Darjung Ind Ltd. It has a standard lampcord (two wires) coming from it as well as one white, one black and one yellow wire. The original touch/dimmer switch (no identification on it) had one white, one black, one red and one yellow - no lampcord. Thank you very much for your help!


The black and the white will go to the lamp ,eg,output.The yellow is the sensor wire which should be firmly attached to the metal base of the lamp ... Vacuums

Wiring diagram for Model #11635922500 - KENMORE Upright vac I took the cover off of the vacuum to repair the power cord and must have pulled a wire out of its wire nut by the sweeper bar. If I had a diagram it would be no problem to replace. The bad has four short gray wires coming out of it. It is one of the gray wires that has come loose.


... Kenmore Vacuums

Titan therm o dial T770 wiring diagram space heater I need wiring diagram to make repairs


... Vacuums

Wiring diagram took wires off motor and do not know which goes where.There are two main from plug in one whit one black then two of same coming from light in front.On the motor ther are more terminals than wires.On diagonal corners there are black dots.Can you please help this cost 800$ and do not want to burn the motor due to crossing pos and neg.Do you have a picture or know where I can find?


... Oreck XL21 Bagged Upright Vacuum

I need a relay board for a Nutone CV 450 12.6 amp dual motor vacumn unit. Where can I locate one? Part #??? Unit will run by itself, then shut off. Unit wll not run at all. It has a mind of its own. Crossed a couple of wires on one of the relays and the unit runs smooth as silk. I assume its the relay, but can't locate part number.


Why not just replace the relay? Part number 1094117... ... Broan-NuTone CV450 Central Bagged Central System Vacuum

Hello, I,ve just bought an Italian designed 3 bulb 70's wall lamp. It has a 2 wire lead feeding out with 2 wire lead running from one bulb socket To the other 2 inside the casing. I'm trying to wire it in my porch which has 3 wire cable coming from a 13amp plug for power. Any suggestions on making this work please ?


... Vacuums

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin


... Vacuums

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work


It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Wiring Schematices Hello, Thank you for posting the wiring schematics on FixYa. Those are the ones I needed. However, I cannot make them out on the webpage. So, if you could kindly send me a copy to my e-mail address, it would b highly appreciated. Prefferably in .pdf format if possible. Thank you very much. Desperate To Repair Kent


I had the same problem after not paying attention to the connections when replacing my motor. I spent days searching for information and only found several non-answers with small photos that no one can read.I contacted Oreck for wiring information. T ... Oreck XL Ultra Bagged Upright Vacuum

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...


The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My Hoover Wind tunnel has even a cheaper on/off switch and now, you can't buy a new one. I used to go to their website which had a wonderful diagram of the 'guts' but now the only parts are the obvious ones, belts, filters etc....I have to vacuum twice a day and I should be the test person cause its on and off on and off, but now for a vacuum I purchased 3 years ago for over 200 bucks and I can't fix it myself really makes me made or do you know where I can get this part? help? if not, I will ne


Have you tried going to appliancezone.com? I go there when I need parts... ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

HI, I HAVE ELECTROLUX LE(similar to 2000). I HAVE TAKEN IT APART, CLEANED IT, AND PUT BACK TOGETHER. IT SEEMS I GOT THE WIRING WRONG. CAN ANYONE GIVE ME A SIMPLE WIRING DIAGRAM FOR THIS VAC? THIS MODEL HAS NO CONTROL KNOB. IT'S NOT COMPICATED BUT I MUST HAVE CROSSED SOMETHING BECAUSE IT SHORTS OUT NOW. HAVE CHECKED ALMOST EVERYTHING ELSE. THANKS.


... Electrolux UltraLux 2000 Bagged Canister Vacuum

I have the new power on/off switch to replace the old one(Rainbow vacuum). However the new switch has 4 contacts & the old one has 6. Need wiring diagram.


Simply pair 1 each of the power head leads and motor leads on to one terminal and wire the cord as on previous switch. ... Rainbow E series Canister Wet/Dry Vacuum

I have a remote Hunter Ceiling Fan w/ remote 1-2-3 fan speed buttons and one on/off/dimmer light button. Model Number CP-9110R. It only has one pull string and it is for the light. I would like convert the light to work off of a simple wall on/off switch and the fan to be controlled by a 3-speed pull string. Can I by-pass all the sensors and make it work?


I see noone has answered so I will.Yes,it could be done,but if there is not a conversion kit for your fan,it would not be wise to do it.For starters,all of the things required would probably cost at least $15.Also,there is at least one tool you would ... Vacuums

Power cord wiring diagram


... Oreck XL Ultra Bagged Upright Vacuum

Oreck XL Is there any chance you could e-mail me the wiring diagram for the Oreck XL? I just can't read the one that's on-line. Thanks, [email protected]


I would advise you to ALWAYS to FIRST UNPLUG THEIR VACUUM before beginning any service procedure. The motor has 5 wires to the motor as stated in the Oreck owners manual, tow are for the headlights, one is a ground wire, and the other two are f ... Oreck XL Ultra Bagged Upright Vacuum

Where can i get a wiring diagram for the Numatic Hzdq 570-2 2000w as one of my work mate have disconnected all and has not a clue where they go back on the new motor. thanks


... Vacuums

Hi, can you email me the version of a XL Oreck wiring diagram. The one on line is too small to see


1. Try zooming in on the online diagram.\015\0122. Copy and paste into a paint shop type program, then enlarge it. ... Vacuums

I have a coralife aqualight model 53008. It uses two 65watt compact bulbs. The whole light quit working one day. I tested the bulbs in another aqualight I have and the bulbs were fine. I want to know where the ballast is. I opened up the ends and the wires are so secure I cannot pull on them to locate a ballast. Please advise if this is a ballast problem and how do I replace it. Thanks Linda


... Vacuums

I recently made a long distance move and the charging wire for my Electrolux Pronto 2 in 1 didn't make it to my new home. How do I get a new one? Thank you. Your promptness of reply will be greatly appreciated as I miss this very handy gadget. Thank you, Marie


Hi,You can buy it separately in the Electrolux service center if you need it urgently.Please choose the are in electrolux and choose the nearest service centre.elsebuy onlinehttp://www.bizrate.com/vacuum-ac ... Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne

The removable filter at the front is cleaned regularly, and is not clogged. However, the machine appears to be suffering from being clogged by dust, as it has started to make a high pitched noise, and I fear it may burn out. I can see some dust inside the front panel but cannot see how to remove the front to clean it out. (NB. I have located two screws - one on either side - but cannot see how to proceed further.) Please help! Thank you.


\015\012\015\012Hi,Here\015\012is a tip that I wrote about my Bissel but I bet you have the same\015\012problem and the hose is clogged...Bissell Bagless Upright\015\012 ... Vacuums

Need wiring diagram for electrolux 1521


... Electrolux Lux 5500 Canister Vacuum

I have an Electrolux Epci 3500 Sr upright vacuum cleaner ... 100 percent positive switch is shot and one of the wires inside is fried but before buying a new handle assembly online how do I check the motor to make sure it's not fried?


The switch is replaceable, so you don't need to replace the complete handle assembly. I've got a 3500 that I replaced the switch on and it works great now. You can get a new switch at the local Aerus Electrolux store. To find the nearest store, ju ... Electrolux Epic 3500 Vacuum

I am looking for the Wiring Diagram for Rainbow E2 controller. One capacitor has been burned, And I would like to found out its nominal value. Thanks Victor


... Rainbow E series Canister Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0723 seconds