Having problems with your Electrolux Lux 7000 Bagged Canister Vacuum ?

ElectroLex Cannister model C101J Cord won't retract, trying to remove hard plastc side strips. Appears to be 'one-way' lock in 'T' channel - suggestions unlock?


Answers :

Use a screwdriver to pry on the top or bottom of REAR cover. I t is held by 4 prongs that fit into 4 holes in tabs. It took a little effort to do mine but it came off. From there you can access retractor mechanism.
Repair Help & Product Troubleshooting for Electrolux Lux 7000 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

ElectroLex Cannister model C101J Cord won't retract, trying to remove hard plastc side strips. Appears to be 'one-way' lock in 'T' channel - suggestions unlock?


Use a screwdriver to pry on the top or bottom of REAR cover. I t is held by 4 prongs that fit into 4 holes in tabs. It took a little effort to do mine but it came off. From there you can access retractor mechanism. ... Electrolux Lux 7000 Bagged Canister Vacuum

WE CANNOT CHANGE THE CHANNEL ON RADIO IT HAS DEFAULTED TO RADIO ONE AND THERE DOES NOT APPEAR TO BE ANY WAY OF CHANGING IT TO RADIO TWO HELP PLEASE!


I was never too fond of Jimmy young however Try switching of unplugging for a few mins then try a new auto scan this will search for available frequencies ,which I hope picks up Radio 2 in your case..Good luck ... Vacuums

I am putting my bissel 8910 back together and behind the motor there is a black 3-way tubing connector. One side goes to the pump discharge, one side goes to a tubing going to the right rear wheel (facing the unit from the front) I don't know where the third side goes to. I do not seem to have another tubing for this one to go to? Maybe it is lost or ?


Hi, its hard to know what its for without seeing it. The best way to test this is to start the machine and vacuum a part of the carpet/ floor. Then let me know wht the vacuum is not doing. This will narrow it down. Please, get back to me. This sounds ... Bissell 8910 ProHeat Clear View Upright Vacuum

One of my Levolor double-honeycomb blinds is no longer level (one side goes up faster than the other). Another of my blinds (same brand, model) seems to have broken, with one side no longer rising. Both blinds are about 9 years old. Is there any way to fix them? Or, does it make more economic sense to replace them? Thank you!


Hello,\015\012\015\012This problem is a common problem on this device, there are many people\015\012who are searching for the answer on what to do and what are the causes\015\012of this problem. The answer to this is still not clear. ... Vacuums

My dyson dc25 vaccum lock for the beater bar keeps comming unlocked,i use a screw driver to lock the bar side door ,but the carpet seems to unlock when i use it and if i don't watch it the beater bar will slide out we baught the unit about four months ago and love it


... Vacuums

My dad has a pro 2020 scanner which he has deleted or locked out channels on. So when he scans for channels it skips lets say channel 2,3, & 5. And now he would like to use it but does not know how to unlock the channels or reprogram them. Can you help me out. Are the channels reprogramable or retrievable?


You posted the wrong appliance, is this a radio scanner or a vacuum??????????? ... Vacuums

I have a Sleeptight Imetec Electric Blanket with timer and Dual Controls one for each side of the bed recently the timer was set for 45 minutes and when 45 mins elasped it went off and the control light began to flash which is normal however it is since stuck in this mode light flashing will not heat just keeps flashing is there any way of sorting this the other side of the blanket for the other side of the bed seems to be ok although it did the same thing but reset itself any ideas Regards


... Vacuums

I have Necchi Lydia 544, inheretade, and don't know which way the needle is fixed! what side does the flat part of the needle face? Also, what are the two bobbin holders on behind the main body of the machine, and how do they work? And, how the hairy heck! do I thread it? finally, for now! How do I get the bobbin holder to ...a...hold the bobbin, and b...make it stay in the machine, ..well, it obviously attaches in one way only, and I cannot find that way!? Thanks, Yvonne.


Hi,Here are some websites with useful information on your machine:http://www.free-guitar-tablature.com/Lydia.html This one shows how to take the bobbin case out with pictures.http://www.youtube.com/watch?v=FbEMwLNzsG4 ... Vacuums

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge


... Vacuums

The hose does not stay connected to the wand although the collar appears to be locked in place for a while. Is there a replacement part for this? Also the holder where the wand goes in has split horizontally. This appears to be one piece with the body of the unit. Is it repairable? It still holds the wand but continues to get worse.


... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a roomba 551. Have cleaned and removed every bit of dirt and hair off it bu the brush cage won't close when the larger bush is put in. The cage will only click locked on one side, and the other side keeps hitting the brush and won't close. It's almost as if the bursh itself is not even, but this doesn't seem to be the case either. I've even tried removing the yellow rings, but makes no difference. Occasionally it runs fine, but most of the time the roomba just hobbles and clacks as i


Hi, had the same problem, it was like the main brush no longer fit into it's slot, so the brush cage would not latch. I discovered that the yellow bearing tip on the main brush twists off, and inside I found a lot of hair twisted around the pin. Th ... Vacuums

The removable filter at the front is cleaned regularly, and is not clogged. However, the machine appears to be suffering from being clogged by dust, as it has started to make a high pitched noise, and I fear it may burn out. I can see some dust inside the front panel but cannot see how to remove the front to clean it out. (NB. I have located two screws - one on either side - but cannot see how to proceed further.) Please help! Thank you.


\015\012\015\012Hi,Here\015\012is a tip that I wrote about my Bissel but I bet you have the same\015\012problem and the hose is clogged...Bissell Bagless Upright\015\012 ... Vacuums

I have a singer 2808 and the bobin case seems to come out each time i try to use the machine. it appears to have broken on the one side. is it possible to get this repaired and how much will it cost. i would also like to get hold of a user manual.


Hi This section is to do with Vacuum Cleaners, please re-list under the correct section. Many Thanks ... Vacuums

Should the handle stay in the hose when it is detached from the machine? My DC04 did but we just got this one and it doesn't seem to stay in. There doesn't appear to be a way of keeping it in?


There is two versions of hose for the DC04 just check you have the correct hose on your machine.If your machine is green, the hose should have a rubber cuff, that just pushes on and of the metal tubeIf your machine is any other colour, the ho ... Dyson Ball DC24 Bagless Upright Vacuum

The wheels on one side are not turning....any suggestions?


... Polaris 360 Pool Cleaner 360

Have older white serger (White Super Lock 503) looking for threading instructions. which way the needle goes in (and it only has one.)


... Vacuums

I have a DC07 Animal and the roller stopped rolling. I appears that the roller sheared off on one side.


Your belt could be torn or the teeth could be worn off. Contact dyson for a local repair rep. ... Dyson Vacuums

Roomba My Scheduler started making a "grinding" noise every now and then until one day it just started grinding and then stopped (I could restart the unit, however it repeated the grinding and stopping). I have checked the wheels and all of the gears appear to be in good order. I have a hunch the brush motor may be stripped. Any opinions? Thanks: RAnderson


Hi!\015\012\015\012Further investigation (running diagnostics mode) revealed the impeller (in the dust bin) was out of whack. I got another dust bin from EBAY and replaced the impeller and motor. Unit works fine. ... iRobot Roomba 4210 Bagless Robotic Vacuum

I just bought a Hoover Platinum Collection MaxExtract Carpet Cleaner (Model No. F8100900). This is the first time I've used it and got half way through one room and the unit cut off and has no power at all. No lights anywhere. On/Off button is inoperable. I checked the outlet and it's still operating so it's not a circuit breaker issue. The problem appears to be with the machine. Has anyone heard of this happening this quickly? Is there a reset button on the machine>


... Hoover Vacuums

Belts I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do t


It is the flat belt that gets stretched and should be replaced at least every 6 months. The V belt wears down so it won't it right in the brush roll V. Maybe the belt tensioner wheel has a problem, sometimes they get hook up and won't engage the V ... Vacuums

Accessory lock is stripped, need a new one? not sure how to fix this prob.


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=11557&thid=564785\015\012Accessory lock\015\012Posted by goulds5 on May 02, 2008\015\012Accessory lock is stripped, need a ... Kirby Ultimate G Bagged Upright Vacuum

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do they re


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=675093\015\012Generic problem for all Vacuums\015\012I have a Hoover self-propelled\015\012Posted by kl ... Vacuums

A 'burn' hole has appeared in the Microwave Outlet Cover causing arcing (or similar sparking and blue flashing!). Would replacing this cover with a new one solve the problem or does it suggest something that would quickly reoccur? Would it be an economical repair or should we ditch the machine for a replacement? Thanks in advance etc it is appreciated.


... Vacuums

2002 esb avalon tanning bed 220volts. 2 lights out on top side by side and two on bottom side by side and one by itself checked all fuses on top and bottom one was blown changed it to new fuse and it blew right away what could be the problem


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0579 seconds