Having problems with your Electrolux Trilobite Vacuum ?

Trilobite robot Frozen beater brush continual running error

\015 My trilobite has been working fine for years now the beater brush is running with out any computer control.The Display ERROR # 10I can turn off the robot and the brush is still running.Any suggestion what parts of the PCB components to repair or PCB schematic available or suggestions ?Thanks\015

Answers :

If you can't find proper service from your country, please send your Trilobite to Finland
So have done some other people around europe too! :)
I am a professional with Trilobite robot's.
No service manual available, even for me...
\015\012For error 10 (power failure) there is several possible "burned" component's. 8 to 10 can be in same time faulty
\015\012Different in every time
\015\012After two weeks investigation I usually put totaly new prosessor card.
\015\012
Address for service is:
Oy JVV Tekniikka Ab
Mestarintie 43
SF-28800 PORI
tel. int +358 400 126597
remember add your return address with short description of fault and put the charged in the parcel
Repair Help & Product Troubleshooting for Electrolux Trilobite Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Trilobite robot Frozen beater brush continual running error


If you can't find proper service from your country, please send your Trilobite to Finland So have done some other people around europe too! :) I am a professional with Trilobite robot's.No service manual available, even for me... ... Electrolux Trilobite Vacuum

My Roomba runs for a while and says error 2 to clean the brushes. This happens with cleaned brushes. And I have followed the instructoins. i have got a brand new set of brushes also. When inserting them the same problem continues. The floor is clean.


Remove the two round rings.....this has worked for me like a charm since! So glad to have the Roomba back up and running! ... iRobot Roomba 560 Robotic Vacuum

My iRobot Roomba runs for 5 minutes, then it say error 2 open brushes clean brushes, which i did, then 5 minutes later it start again saying error 2 clean brushes.


... iRobot Vacuums

My wife had some thing caught in the front of our dyson dc17. Now when the beater brush is running it makes a noise. It still vacuums alright. I cleaned out the area around the beater brush.


It could be the belt has striped some of the teeth and may need replacing or the teeth on brushbar here is video how to check ... Dyson DC33 Animal Bagless Upright Vacuum

Runs for awhile then says error 2 please remove and clean roomba's brushes i do then runs for awhile and says same thing no dirt on brushes?


I had the same problem. You must clean this parts and inside this parts: Remove hair with cleaning toolRemove Roomba's brush bearingsClean Roomba's brush bearings with cleaning tool ... iRobot Roomba 560 Robotic Vacuum

Robot runs for about 5 min. then says clean brushes. brushes do not turn


The dust build up in these Roomba's do create a problem in all operating phases\015\012Keep in mind if taken apart every 6 months and cleaned inside they will operate like they should ... iRobot Roomba 560 Robotic Vacuum

Same problem as voirjs 12/29/09 - runs a while & needs brushes cleaned w/same repeat scenario. have been doing all of the cleaning as felix80 said on 1/8/10; but it still continues the run awhile & need cleaning behavior. a more indepth solution is required.


I called iRobot Customer Support, and they are sending me a new cleaning head module. ... iRobot Roomba 560 Robotic Vacuum

It continually repeats error 1, and will not run.


... iRobot Roomba 560 Robotic Vacuum

Beater brush is good, vacuum running no suction


This sounds like your vacs dust passage from the rotary brush to bag is blocked ? you can diy this if you turn vac over to show the brush and covering cover you will see cover is held by some screw/bolts ? remove these and cover then the brus ... Electrolux Vacuums

4296 Robotic Vacuum _ Brush quit spinning


I had the same prob. i contacted i-robot and was told the motor that turns the brush is shot. there is no replacement part. they offered to replace my i-robot with a new one from the 400 series. at about 60% of a new one. that's the only option that ... iRobot 4296 Robotic Vacuum

Makes clicking noise and runs for a couple of minutes and then says error 2 open roomba and clean brush cage-do that and the same thing happens 2 minutes later


Pet hair often gets sucked into the gear box that drives the brushes and can clog it enough to generate this error. \015\012you need to remove the CHM (cleaning head module) and open the gear box on it to clean it out... you can also visit iRobots ... iRobot Roomba 560 Robotic Vacuum

Beater brush won't run - Dyson DC25 All Floors Bagless Upright Vacuum


There is a switching device that controls this, and has to be sent to Dyson in California for repair, unless you are close to a certifid repair center ... Dyson DC25 All Floors Bagless Upright Vacuum

IRobot rumba 4000 seems to run ok and then starts making a kinda hi pitched growling noise and slows way down. it is very clean(blown clean with air compressor)sensors are clear ,newly installed well lubricated on ends of brush and beater bar, new battery. it seems like the wheel tracks may be dragging . i have cleaned and lubricated where i could on them but can't find a way to totally remove and inspect wheel tracks.


It sounds like your Roomba's brush gears are not working. Run the robot without the dust bin to see if the brushes are turning. If they are not, the robot will need to be replaced. Contact iRobot CS for support at (877) 855-8593. ... iRobot Roomba 4000 Bagless Robotic Vacuum

It's making a very loud noise when running. I have a Bissell Quicksteamer series 2080. When I was using it yesterday it was making a light squealing noise then it turned into a loud racket. I shut it off and and cleaned the brush (lots of dog hair on it) But the racket continued.


... Bissell 1770 Quicksteamer II Upright Vacuum

Dyson Root Cyclone. The brush continues to run when the machine is in the upright park position. How di I fix this please? Neil


Sounds like you have a faulty clutch.\012New clutches are available on eBay ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The motor on my carpet tool (beater brush) stopped running yesterday. The main vacuum still works, but the switch for the carpet tool just clicks and doesn't turn it on.


You have to take it apart. Unscrew screws on bottom, short screw is at the front. turn over with top up. take plastic covering off first, then turn over again. unscrew retaining screws which keep beater brush in. take out beater brush. get seam rippe ... Electrolux Vacuums

The vacumn is running but the beater brush is not turning.


This is from the Dyson website. It gives step by step guide for replacing belt and or beater bar. http://www.dysonmedic.com/DC07%20Folder/DC07%20Belt%20&%20Brushbar%20change.htmlGood luck. ... Dyson Vacuums

Have roomba 550 that keeps on turning around ending up with an error. cleaned the sensors and brushes but no result. when i undo its bottom and put it back it runs until it bumps into something


... iRobot Roomba 550 Vacuum

Runs but doesn't vacuum/****. Sidebrush works fine. Cleaned the roller brushes, and that seemed to confuse the robot and now it keeps going backward a few inches, turning, and then starts going backward again.


Sounds like a sensor problem. pull and clean the front black/white caster assembly and the revealed movement sensor and the 4 cliff sensors along the bottom of the front. Make sure the front caster wheel turns freely. You may have to remove the rolle ... iRobot Roomba 560 Robotic Vacuum

Beater brush runs intermittently - Fantom Vacums Cyclone XT Upright Vacuum


Try changing the the belt.If it is worn it could cause your problem ... Fantom Vacums Cyclone XT Upright Vacuum

Keeps saying error 2 - clean brushes - iRobot Roomba 560 Robotic Vacuum


... iRobot Roomba 560 Robotic Vacuum

I have a Hoover Savvy model U8174-900.. The beater brush only runs sometimes when I pull the unit backward. The handle switch seems OK but I cannot figure out why it is acting strange like this. Tilting the handle up or down does not seem to have an effect on this situaltion. Thanks for your help. Ron Simon


The Savvy has had its problems with the switch in the handle it will need to be replaced. Don the Vacuum Doctor Alb,N.M. ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

My Trilobite starts and runs for about 3 minutes (on plain parquet floor) when it suddenly stops with error 5. One is supposed to clean the role. I did it but the problem remains.


Hi,If you can't find proper service from your country, please send your Trilobite to Finland So have done some other people around europe too! :) I am a professional with Trilobite robot's.Mostly error 7 will be repaid f ... Electrolux Trilobite Vacuum

Model # 116.22102C...the motor is running but the beater bar with the brushes is not turning or picking up.


... Kenmore Vacuums

Brushes run freely on the cog and I put on 2 new belts and new brushes on my Bissell Proheatx2 the brushes do not turn when the machine is running even if I have the handle in the relesed position


I know how frustrating it can be when the brushes don't turn when you're ready to clean.Here's a quick link to troubleshooting steps to assist you:\015\012 ... Bissell Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0957 seconds