Having problems with your Electrolux UltraLux 2000 Bagged Canister Vacuum ?

Full bag indicator light is on, just changed the bag. Motor turns on the cuts off immediately. I already paid $10.00 and there was no solution.


Answers :

Sounds like the hose is blocked, disconnect it and put a coin through it to check
Repair Help & Product Troubleshooting for Electrolux UltraLux 2000 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Full bag indicator light is on, just changed the bag. Motor turns on the cuts off immediately. I already paid $10.00 and there was no solution.


Sounds like the hose is blocked, disconnect it and put a coin through it to check ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Full bag indicator light is on, just changed the bag. Motor turns on the cuts off immediately. I already paid $10.00 and there was no solution. I have an E2000 Does anyone know what all the symbols mean when they light up?


Turn the dial on the top of the vacuum all the way to the right and try it again. ... Electrolux UltraLux 2000 Bagged Canister Vacuum

My Dirt Devil M082476 Full Bag indicator light keeps coming on when I turn my vacum up to full intensity. I have tried changing the bag and checked that all hose is clear. If I leave the vacum on low intensity the suction is minimal and does not increas when I turn up the suction. Is there a solution to this? I look forward to your response


... Dirt Devil M084105 Jaguar Vacuum

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?


First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

Won't dispense water/cleaning solution (bissell proheat clearview) the water reservoir is full as well as the soap. The engine is turning on and the light indicating heat is on is functioning. Any suggestions?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Cleaned all of the lines, shampoo solutions will go through but the water from the tank is not going through. the floww indicator will start to turn then after a second it completely stops. What is wrong with this thing?


... Bissell Vacuums

SEBO vacuum cleaner makes a strange noise and shuts itself off after a few minutes. Suction not working when tube is attached, but works with hand-held portion only. Indicator light saying bag is full/clogged is on, but we've cleaned out the bag, cut away any fur/strings that were wrapped on the turning portion, and cleaned out the refuse valve. Not sure what else to do. Thanks!


... Sebo Vacuums

Have a Miele S658 Blue Moon that cuts out intermittently, sounds like most of the solutions to similar problems indicate the circuit board has gone bad in the hose mechanism.......can just the circuit board be replaced or does the entire hose have to be replaced?


Probably needs a new hose. ... Vacuums

Bissell Pro-Heat 7901-1 no cleaning solution is pumped out. The flow indicator is spinning and the belt is spinning the beater bar. Have cleaned the flow indicator, checked vavles in the solution tank and water tank and they are working properly. Also checked the trigger to make sure it works okay. Any ideas?? Moody Fan


Bissell Pro Heat shampooer - Fill the soap dispenser with extremely hot water and shampoo with only water for a few minutes. There is often dried soap in the lines. Make sure that all filters are clean. Press the soap container and the water conta ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

CUTTING OFF Our Dco7 cuts off after a few minutes of use. If we wait a few minutes and power it back on it will turn on but turn off again by itself.


Ok What is probably causing the problem is an internal error inside the vacuum. What I recomend you to do is take it back where you bought it and tell them what ever is wrong with it.PLEASE RATE MY ANSWER AS SOON AS POSSIBLE! ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Hoover SteamVac is spitting out dirty soultion from the recovery tank, it seems. I have removed the clean solution tank and turned it on to **** up what was soaked into my carpet and it just kept spitting out slowly. When I first turn it on, it spits out a tremendous amount. What could be causing it to spit out solution?


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!


Call BISSELL Consumer Services.\015\0121-800-237-7691\015\012Mon-Fri: 8am to 10pm ET\015\012Sat: 9am to 8pm ET ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Clarke scrubbers helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? ther


... Clarke Vacuums

Henry hoover Hi all, I bought a spares/ repairs Henry on ebay having been told there was no cable rewind and believing that since I had a spare one in the shed it would be an easy fix. However, poor Henry had his cable replaced to find when plugged in, he tries to start but nothing happens. The motor turns once and just cuts out. If you turn it on and off again it happens again. One whir and turn of the motor, then nothing. It blew the fuses out in the kitchen first time too, so could it be a re


Hi it can be the connector at the end of the Henry cable inside the cable rewind unit happened to us! ... Numatic Henry Bagged Canister Vacuum

I have a dyson DC28 vacuum and the power button flashes on and off and the beater bar quit turning. I turned it over and found some string caught on the beater bar which I removed, but the beater bar still does'nt turn and the power button still flashes on and off. I hope you can give me a solution to this problem.


I had the same symptom with my wife's DC28. The problem was associated with the cam driven height adjustment mechanism. The beater bar must rock freely up and down when pressing on the tabs that the end cam lobes actuate. On ours I found hair and cru ... Dyson DC28 Animal Bagless Upright Vacuum

Clarke Instructions helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? t


... Vacuums

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

The beater bar on my Dyson won't turn. The vacuum runs and suctions but the bar won't turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won't turn


The belt doesn't have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won't operate the way it is supposed to. You can get replacement Dyson Belts here: ... Vacuums

After turning on power , brush roller freezes and indicator light turns red


Try turning the roller by hand UNPLUG VACUUM FIRSTit should turn very easy, otherwise it is bindingall uprights have this problem eventuallyhair and fibers get in roller bushing and seizeluckily disassembling is relatively easy, same ... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

The unit sprays for the first few seconds after I turn the unit on and then stops spraying any water or solution. I turn it off, wait a few minutes and the same thing happens. What is going on and how can I get it to work properly?


This sounds as though the pump belt is slipping. This may be caused because the pump belt has stretched slightly or the pump is seized and will not turn. Remove the pump belt and turn the pump rotor with your fingers to see it turns freely. If ... Bissell 7901-R Clearview Proheat Plus Upright Vacuum

Eureka Boss - Belt is not broke but brush will not turn. I have already turned it over - checked belt - and pushed the reset button.


The belt may look fine but they can still be stretched or worn and it won' turn the brush. Try changing the belt and see what it does. You can get Eureka belts here: ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Cleaning solution does not come out of the rotating cleaning head or the hand-held nozzle the solution pump seems ok but does not run (electrical continuity check between the two leads on the pump show very low resistance so they seem to be intact) - no dirt or blockage is apparent (it is a very simple device with 1 moving part wires to the pump also pass a continuity check THERE IS NO VOLTAGE on the pump leads from the control circuit board when I turn on the "manual" cleaning mode - a


You can contact Bissell directly at the following\015\012\015\012For UK inquiries:\015\012Monday - Thursday 9 am — 5 pm\015\012Friday 9 am — 4 pm\015\012\015\012BISSELL Homecare (Overseas) Inc ... Bissell SpotBot Robotic Wet/Dry Vacuum

Used the Bissell Pro-dry 7350. Turned it off emptied dirty water and re-filled hot water & cleaning solution. Wouldn't turn back on. Have only used 3 times.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have the Quick Steamer Plus 160 Series/2070 Powerbrush. It will not release cleaning solution and will not pick up solution that had already been dispensed. Is this something simple I can fix???


I checked the bottom of the fresh water supply container and all\015\012was well there then I used a pin in the tiny air valve on the container.\015\012Turned the machine on, pulled the lever to release water and held\015\012it for several minutes an ... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

No power The vacuum worked. Then cut off. I changed the bag and let it sit a bit. Then it turned on. I used it for about 5 minutes and now it's off again and won't turn back on. Is there a fuse or something I can reset?


Miele Capricorn whole unit shuts off totally off when I am using the Miele and I turn the powerhead sharply to the left. It an on-going problem that I have had serviced serval times. The last time the place I purchaced it from replaced the whole bead ... Miele S514 Solaris Electro Plus Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0733 seconds