Having problems with your Electrolux UltraLux 2000 Bagged Canister Vacuum ?

THE VACUUM CLEANER WORKS FOR 6-7 MINS THEN CUTS OUT, THEN AFTER A WHILE STARTS AGAIN FOR A FURTHER 6-7 MINS THEN KEEPS REPEATING THIS PROBLEM


Answers :

What you describe is typical of a machine that's overheating. This is almost always caused by a blockage. Check the machine thoroughly for any blockages, including any filters, and my bet is that you will find something that shouldn't be there that needs removing (or possibly replacing).\015\012I hope this helps.  Good luck!
Repair Help & Product Troubleshooting for Electrolux UltraLux 2000 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

THE VACUUM CLEANER WORKS FOR 6-7 MINS THEN CUTS OUT, THEN AFTER A WHILE STARTS AGAIN FOR A FURTHER 6-7 MINS THEN KEEPS REPEATING THIS PROBLEM


What you describe is typical of a machine that's overheating. This is almost always caused by a blockage. Check the machine thoroughly for any blockages, including any filters, and my bet is that you will find something that shouldn't be there that n ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I have a vx550cc that keeps kicking in and out quickly, then shuts down for a few seconds and starts up kicking in and out again. There is lots of suction at all the outlets and sweeps. The dirt bucket has been emptied and the filter cleaned. Al the LED lights light up when the motor kicks out, then back to one green when it starts back up. This unit has worked great for four years with no problems.


... Broan-NuTone VX475 Bagged Central System Vacuum

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha


... Eureka Smartvac 4870 Bagged Upright Vacuum

I have a Uro-Pro vapor steam cleaner Model EP95 Have used it only a few times and worked well Today it worked for about 5 mins and then nothing from the wand but steam started coming out from under the canister. What can cause th is problem and is it fixable


... Euro-Pro Steam Cleaner EP95 Canister Vacuum

No water I have had a bissell proheat for 3 months. Now, the water won't come out in either the floor cleaner, or the tools. I have checked all the stoppers, they all seem to be in working order. It started to work for about 5 min, then stopped again. Is this a fixable, quick problem, or should I return it as being defective?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

The Beater Bar keeps Shorting out, we had to replace it a while back and it was working really good, then it started shorting out, do you know what the problem is?


HighnTools \015\012posted this solution a while ago. There are so many people having similar issues. This might be related to your \015\012problem:\015\012 \015\012I \015\012have finally f ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Keeps turning itself off, have to wait 20 mins then it starts again. Is it a wiring problem?


The motor is likely getting too hot ... that will trip a thermal protection breaker .. when it cools after 20 minutes then it resets ... the motor gets hot when there is not enough air flow thru it ... you should check or replace all the filters in t ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have the Janome 6600 P. Beginning a seam the thread knotted and the machine made noise and needle would not move either up or down. I manually moved the needle using the handwheel and cut away the knotted thread. I began sewing again but instead of starting at the edge began about a half inch down, forward stitched, reversed to lock threads and problem repeated and received the message to "Stop for safety purposes". Did that. Referred to the manual, tried manual recommendation. Did not work. I


... Vacuums

Problem with powermate nozzle keeps tripping. hit overload reset and the lite comes on and starts to work but within 5 seconds shuts down again...help


... Kenmore 22313 Bagged Canister Vacuum

I have a DC04 and when i switch it on it works for 10-15 mins thens stops working for about 20 mins then starts working again.


Your vacuum is overheating - that's why it cuts out. You need to check everywhere possible for blockages and also make sure the washable filter is clean and dry. If the machine has been run without the washable filter in place, then the exhaust filte ... Vacuums

I have a Chamberlain Liftmaster Professional 1/3 hp garage door opener. I'm unable to find the model number, but it was made in April 2004 and has an orange learn button. It has been working fine since it was new, but now will not open or close when the code is entered on the touch pad. When the problem first started the door would close, but not open. I have tried to reprogram a new digital code, but it does not work at all. There are no problems when opening or closing the door with the re


... Vacuums

My Dyson animal seems to have an electrical issue that I am unable to pinpoint. Neither the wand nor the floor vac have any suction AT ALL. In fact the vac makes absolutely no sound and you wouldn't even know that it had power to it unless the rollers are turned on, the rollers work just fine. I had this problem start about a month ago and then it just started working again after messing with it for a while, now it has happened again and I am getting a little agitated! Please Help!!!!!!!!!!!


There is a filter inside the canister, and by your description it sounds like it needs to be cleaned. if you remove the filter and blow it out using a air compressor or using a slightly ridged brush and tapping the filter out this should solve your ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hoover Vacuum works, then stops in 3-5 mins. Works again in a couple of hours


More than likely there is an inline over current breaker that is bad or weak and needs to be replaced. This is for overcurent protection of the motor. It is fairly common for the protection circuit to go bad ... Vacuums

Vitamix 5000 stopped working. It stops working each time I use it; while blending I first smell a burning smell and then blender stops and will not start again. After sitting overnight it works again next morning and repeat same process. Any ideas how to repair?


It has an internal thermal shutdown. Let it sit for a while and it will reset itself. You can expedite by putting the motor base in the freezer for a few minutes, or by blowing a hair dryer into the base of the motor. ... Vacuums

I have owned my kirby sentria for 2.5 years and have had no problems until now. The vacuum still works but I cannot lower it all the way down or the light will turn off and it will start to smell like something is burning inside. I use it on the 2nd or 3rd setting with no problem. I have changed the belt and cleaned all the hair and strings that were on the roller but it still has this problem.


Kirby has a 3 yr back to base guarentee so contact ur local rep or kirby direct and thy will sort it all from there, hope this helps :) ... Kirby Vacuums

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!


Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

I have a Bissell 3576-2 sweeper. It's worked for years, but now it won't start. The light turns on but the motor doesn't. Before this problem started, I took the machine apart to clean all


... Bissell CleanView II Plus Upright Bagless VacuumVacuum

The roomba 560 keeps going in circles after it hits an object. Or it will keep hitting the object repeatly until you pick it up and move it. I have cleaned the sensors and wheels and it still does not work properly. Thank you.


... iRobot Roomba 560 Robotic Vacuum

Carpet vacuum attachment quit working after sucking up a bedskirt. Bedskirt has been removed but carpet attachment will not work. My old vacuum had a reset button on the carpet attachment for use when the carpet attachment sucked up something and turned off. Does the Hoover have such a feature, and, if so, where is it? If not, how do I fix the problem and how do I keep it from recurring? Model # S3765-040. Serial # 100700081298. Purchased 2/08.


I have a Hoover Conquest approx. 4 yrs old. The turbo head is not working Model No. PB4 230-240V AC 50Hz 200w CS4901N (N127) I have been trying to locate another one or another one similiar to fit my machine ... Hoover Vacuums

My purple Dyson Animal (without the ball) isn't working correctly. When I turn it on, the red power light, as well as the medium pile buttons flashes. When I first turn it on, the brush rotates for 3 to 5 seconds, then once I start moving the vacuum, it stops and that's when the lights start flashing. I've checked the filters, they are dry and installed correctly. What could be the problem?


I need help repairing my Dyson. I cannot push the buttons down to select Short pile/Medium pile or bare floor. The buttons will not push down at all. It will not allow me to select anything. I have very short pile carpet so it does not pick up that w ... Dyson DC28 Animal Bagless Upright Vacuum

My lux 7000 has a new bag but when i start to use it with the power unit or without the unit shut's it self off i can reset the lites or the motor if you will by clicking the on off switch 4or 5 times and i'm ready to go again untill you start to work and off it goes you can repeat the switch thing as long as u want, it just won't let u vacuum ,it turn's it self off .I blew it all out but found nothing in it. if u don't try to vacuum it will run as long as u want to listen to it. Can you


Have you replace the afterfilter? It may also cause this if rather dirty. It's located under the tool caddy/air diffuser on the back half of the machine.\015\012Try this: Disconnect hose, turn on vacuum. Does it continue running? If so, pl ... Electrolux Lux 7000 Bagged Canister Vacuum

I heard that a class action lawsuit against Oreck Vacuum is being started because of all the problems customers are having with their vacuums. Does anyone know about this? My Oreck is only a couple of years old and keeps burning up belts. I took it in after only one week of usage when I started to notice white smoke coming out of it and the smell of burning rubber. I feel like I got the old run-around, when the service tech told me he couldn't find anything wrong (but replaced the burned up belt


You are correct about the fact that legal action has been taken. Go to this link to read more\015\012\015\012 ... Oreck XL2200 Bagged Upright Vacuum

DZ9080 IRON IS NOT VERY OLD, BUT HAS HEATING AND STEAMING PROBLEMS. IT MAY BE ALL HEATING RELATED! MY WIFE WILL SOMETIMES JUST LEAVE IT "ON" FOR TWO HOURS AND THEN IT WILL START STEAMING AGAIN. I CANNOT MAKE SENSE OF THE HEATING INDICATORS; SOMETIMES IT WILL STAY GREEN NO MATTER WHERE YOU SET THE DIAL ---- AND IT DOES NOT FEEL HOT! WHEN I TRIED IT AGAIN TODAY, THE SHOT-OF-STEAM WORKED FOR A WHILE (AND THE SPRAY WORKED), BUT THEN ALL IT WOULD DO IS DRIP WATER AT THE TIP WHEN TIPPED DOWNWARD.


I couldn't find any warranty information on this iron, but I suspect that the heating element either has a faulty connection or part of it has cracked, making contact at time, but poor contact at other times. The unit will have to be taken apart an ... Rowenta Vacuums

Had my dyson root cyclone for about 4 years now, and in the last year it's had a few problems. About 4 months ago it started to make this awful grinding sound when the roller bar was engaged and I took it to a repair shop and they said it was the roller bar itself. The shop replaced the part and it worked fine for a couple of months and then it started to make the grinding noise again. I tried the clutch reset suggestion (turn it on its side and turn the carpet/bare floor switch slowly back and


Bdepends how much thay charged you for a roller brush because you can buy a good vac for about 100 pounds with a 12 month guarentee so its up to you ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a PQ1500S Brother Quilting/Sewing machine..I am having problems regulating the tension, what should it be set at normally??? I keep having problems with repeated thread breakage, and its a new machine. I have followed all information in the manual. Thanks Theresac57


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0824 seconds