Having problems with your Electrolux UltraLux 2000 Bagged Canister Vacuum ?

Need a wiring diargam to look at

\015 Looking for advice on how to connect the right colored wires on the motor of electralaux 9o vacuum. Need help with the wiring for this vacuum.\015

Answers :

You won't find a diagram.
You will have series of yellow and white and sometimes gray wires on the outside of the motor housing and often a letter code etched on the housing , indicating the original wiring from years ago, red, blue, yellow, however the newer wiring eliminated those colors.
These wires are almost fool proof as they will align with the longest wire at the furthest point,a center one piggy backed , etc however before starting please post back to advise if you have removed the rewind and or motor and if so, did you disturb the motor wiring inside the motor shroud.
Please post the original problem you opened the vac for as well and I will try to walk you through this
Repair Help & Product Troubleshooting for Electrolux UltraLux 2000 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need a wiring diargam to look at

You won't find a diagram. You will have series of yellow and white and sometimes gray wires on the outside of the motor housing and often a letter code etched on the housing , indicating the original wiring from years ago, red, blue, yellow, ho ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?

Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

We have a series e rainbow cleaner. my wife had been using it i turned off and turned the canister up sie down to get the serial number. it would not turn back on.we need a new hose and thats why i was looking for the serial num. it has a rocker switch and the motor will work on low but will not run on the suction side. i have checked the wiring harnesses out as best i could without taken it all apart. im wondering if it may be the switch. it started once and then stopped.

There is one way to verify if it is the switch.It's kind of dangerous though,but not too bad.You need an extra piece of wire,fairly thick.I would use 4 guage myself.Hold it with pliers,just in case it gets hot.Turn the switch on and hold the wire to ... Rainbow Vacuums

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n

From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

Lil Rider tractor need help with wiring

... Trademark Lil Rider 360 Battery Operated 4 Wheeler - Red/Yellow

I bought a new motor for my Riccar 8850. The new motor has 3 wires and the old one has 2. Which color wire is the ground? (or, which color wire don't I need?)

The third wire is a hot wire that goes to the headlight. ... Riccar 8850 Vacuum

Need a wiring diagram for a karcher puzi 100 yellow. Mainly need to know which way round the wires go on the switches?

... Vacuums

Need proper wiring connections inside unit, where they have pulled apart from squeeze connectors.(Wiring diagram needed) Can someone E-Mail this to me? Fritz (an ''old'' mechanic) Folks I have talked to, say there is no specific model number for these units. They are just described by name, and serial #. and I have relayed exactly what was labled on the unit. Please post this and quit asking me to enter a "valid" product.

Fritz , thanks please confirm... there are likely more than 2 leads from the motor?? I have not seen or worked on the Tristar CXL as it is very new.You will have a high low function but: Should the power head function at both spee ... Vacuums

I took my durabrand toaster oven model t0-80 apart and i need the wire diagram to put wires back on it cause it needed cleaning.

... Vacuums

Need connector wires inside wand. Electrolux central vac. 16" wand 1 1/4" wand dia. Don't need wand, just the wires.

Go to a store like Lowe's and look in their electrical department. You need wire the same gauge size (stranded or solid) and comparable insulation. Hope this helps! ... Vacuums

Trying to attatch the wires from the light kit to the fan but the blue and white wires from the fan have white caps on them covering the wire. Do these need to be removed in order to attach the wires with the wire nuts? If so, how are these white plastic caps removed?

They're called "wire nuts". Turn them counterclockwise to remove, lay the wires you need to join side by side with the ends of the bared sections even and screw the nut on. lp ... Vacuums

Hello! I have a Rainbow vacuum Model# D4C that needs a switch. I am only able to get the new style 4 wire switch and it has the 6 wire. Can I make the 4 wire switch work in place of the 6 wire?

... Vacuums

Need to replace power cord on Hoover windtunnel need wiring help

Without seeing this it would be difficult to describe. I would take it to a vac shop and let him show you. there are no real schematics for the wiring of these units. I usually would cut off the cable with a few inches of insulation to know where to ... Hoover U5399-900 WindTunnel Lite Upright Vacuum

Hi, I have an old 2 wire chandelier I would like to make a plug-in. I have bought the wire swag kit to change it, but the chandelier wires are unmarked. Both wires are copper and I cannot see an insulator on either side...I need help!! Thanks!

Can you determine some way of telling which wire goes to the center conductor on each of the lamp sockets. (That particular wire,-- however it is identified-- (Maybe a tracer thread? in the woven ins ... Vacuums

Picked the zig cp3g at car boot sale,just what i was looking for,but no instructions just wires been cut,tidy little unit.on the battery transfer switch, red, green and blue. and from lights green,aux brown,and water pump yellow.....firstly how do i wire to power up,and how does the single wires from unit not have return wires,thanks.

Hi,\015\012\015\012For your requirement wiring will be following: the green wire will be from the knob beside\015\012the tree switch to battery switch. Red wire will be from another side of battery\015\012switch to circuit o ... Vacuums

Rowenta Effective Steam Iron DX1700 Need wiring diagram. How do I wire the power cord to the internal Red, Blue, and White wires? What wires are neutral and which are hot?

... Vacuums

I have a Janome Model 556, purchased in 1968 in Zimbabwe. I need to know how to replace the wires of the foot pedal. There were 4 wires used to go into the small plug attached to the machine, however the wall plug only had 3 wires.

... Vacuums

Hello, I am looking for a wiring diagram to install a touch/dimmer switch by "Comfort" mdl # RH-934B - Darjung Ind Ltd. It has a standard lampcord (two wires) coming from it as well as one white, one black and one yellow wire. The original touch/dimmer switch (no identification on it) had one white, one black, one red and one yellow - no lampcord. Thank you very much for your help!

The black and the white will go to the lamp ,eg,output.The yellow is the sensor wire which should be firmly attached to the metal base of the lamp ... Vacuums

I need to wire the switch to my coleman 2234 push button 12v water pump in my camper trailer. it is wired to the battery now with the "red" connected through a small fuse. i just cant figure out where to wire the on/off switch to.

Hi there. When connecting a switch, it is important to remember that a switch will only "break" the positive (+) circuit, while the neutral wire will go directly to the battery. So, basically split the red wire coming from your pump and connect the s ... Coleman Vacuums

The handle was getting hot and we opened the handle and the wires were melted around the switch. I need a part number for it. All I have seen are 2 wire and this is a 3 wire. Thank you.

Had exactly the same problem with my upright Eureka Model 5893\015\012bagless. Eventually, the handle would get hot, and finally it just\015\012quit. When handle was disassembled, the wires were melted and it was\015\012toast. Ordered a switch aft ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Wiring the switch for a kenmore vacuum cleaner I need to know where teh different colored wires go. It had a short in it so I replaced the plug but think I wired it incorrectly. Its a Whispertone 300 model 116.28612790 The canister works but the beater bar doesn't.( it worked before a rewired the switch. Thanks

... Kenmore 23313 Whispertone Bagged Canister Vacuum

Wiring diagram Need wiring diagram for the motor wiring.

\015\012\015\012HI, tell me is this you want,, \015\012\015\012Gunjan:-) ... Vacuums

Wiring Schematic I need the wiring schematics for my XL3600HH, as I am replacing the motor and did not receive the schematics. Unfortunately, I can not remember the exact wiring. Please help. Thank you

Hope this will help you. There is 4 different ways to hook it up depending on what you have,\015\012\015\012 ... Vacuums

Need to replace belt on Eureka Powerline 12.0 vac. Screws look like Torx head or something on bottom of vac. Are those the screws that need to come out for changing? If so, what size do I need?

No, do not remove the torx head screws for a belt change. If there are any screws that need to be removed for the belt change, they will be phillips head. What is model # of vac?? ... Eureka Vacuums

I need to know how to hook the wires up to the start switch. There are two wires from the external cord and two wires from the internal cord.

White wire to neutral black wire to hot if you post colors I could help you red ,orange, black,pink, blue, or violet are usually hot guessing a striped wire is usually neutral please post colors ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0551 seconds