Having problems with your Electrolux UltraLux 2000 Bagged Canister Vacuum ?

Can I use my ultra lix 2000 to vaccum my new ceramic tile and wood floors? It so how do you stop the beater brushes from turning so that they do not scratch the floor?

Answers :

Yes you can, just set the height at maximum.
Repair Help & Product Troubleshooting for Electrolux UltraLux 2000 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Can I use my ultra lix 2000 to vaccum my new ceramic tile and wood floors? It so how do you stop the beater brushes from turning so that they do not scratch the floor?

Yes you can, just set the height at maximum. ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I would like to vaccum my new ceramic tile and wood floors with my ulta lux 2000 how do you get the beater brush to stop turning so that it will not scratch the floors?

There should be an on/off switch on the right top of the power nozzle. If it's been running, then flip the switch. ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.

Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.

... Kirby Ultimate G Bagged Upright Vacuum

My Hoover spin/scrub floor cleaner has stopped scrubbing- the brushes spin for a few seconds right after turning it on, then stop until I turn it off and then on again. How can I fix this? I do not have a lot of money. I have taken off and cleaned the brushes and bottom vacuum opening.

Hi giacoma11,The common cause for this problem is the belt of your vacuum. It could be that the belt came loose or already worn out and needs replacement. To check if the belt is loose all you need to do is unscrew the bottom of the vacuu ... Hoover H3060 FloorMate SpinScrub 800 Upright Wet/Dry Vacuum

I have a brand new hoover canister s3755 and the beater brush will not turn on the carpet it spins fine as soon as you lift it slightly off of the floor, I can't imagine it is the belt as the mac

It's commonly the belt when they're new. More explained here:http://www.vacuummedic.com/blog/2012/10/09/my-brand-new-vacuum-doesnt-work/Call Hoover and complain, they'll likely send you a new one. The service centers will not ... Vacuums

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?

Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I replaced the beater brush and works on carpet but when I turn the beater brush oof to do floors, the vacuum shuts off.

... LG Electronics Kompressor Pet Care Upright Vacuum Cleaner LUV200R

The beater bar on my dyson DC28 is not turning when it is placed on the carpet. If you lift the sweeper up the beater bar will turn but then when you place it back down on the floor it stops.

... Dyson DC28 Animal Bagless Upright Vacuum

F7220-900 The brushes do not rotate, motor seems to run properly. Brushes did rotate very slowly but stopped when put on floor. Brushes rotate when turned by hand.

Clean the lint filter first. Remove both tanks. Lay the cleaner down(unplugged from power of course) Below the brushes(directly behind them) to the right side as you're looking at the underside is the filter. Squeeze the filter frame, lift it and pul ... Hoover F7220900 SteamVac V2 Upright Vacuum

The roll brush will not turn when on floor. Too much pressure stops brush. Changed belts and still not working

Turn the belt inside out. This problem stems from a design flaw in the mechanism that turns the hoover from bare floor to carpet. After taking it apart I realized that the spring that pushes the belt tight (to make roller spin) is not any where nea ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?

Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile

... Eureka Smartvac 4870 Bagged Upright Vacuum

Dc25 brush bar stops turning when placed on floor. Turns freely otherwise

... Dyson DC25 Vacuum

I was vacuuming with my DC28 Animal and all fo a sudden the beater bar stopped working and NONE of the floor mode buttons work.. no lights or anyhting. I checked for obstructions per the Dyson manua

... Dyson DC28 Animal Bagless Upright Vacuum

The motor on my carpet tool (beater brush) stopped running yesterday. The main vacuum still works, but the switch for the carpet tool just clicks and doesn't turn it on.

You have to take it apart. Unscrew screws on bottom, short screw is at the front. turn over with top up. take plastic covering off first, then turn over again. unscrew retaining screws which keep beater brush in. take out beater brush. get seam rippe ... Electrolux Vacuums

Tristar vacuum beater brush stopped turning - Tristar Vacuums

... Tristar Vacuums

Dc 25 beater brushes not turning around - Dyson DC25 All Floors Bagless Upright Vacuum

Check the belt if thats ok then you will need to check the switch for the brushes ... Dyson DC25 All Floors Bagless Upright Vacuum

Bissel brush stops turning when it come it contact with floor

... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Why does my Dyson Animal Upright Vacuum power light turn red when I tilt it back to vacuum? It will work if I switch it to bare floors and don't need the beater brush.

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Brush has stopped turning..DC 107...all floors model

You need to replace the drive belt. You can get one here:Dyson DC17 Belt ... Vacuums

Chatter We have a Kirby Ultimate G. Since we purchased it it bounces across the floor and the level of the sweeper has nothing to do with it. To get it to stop, it has to be at the highest level. The place we bought it, has done nothing to help us. We tried a new beater brush, no help. If I have to use it at it's highest level to sweep my carpet, I might as well not waste my time. ANy suggestions?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=11557&thid=576381\015\012Chatter\015\012Posted by CANRN on May 06, 2008\015\012We have a Kirby Ultimate G. Since we purcha ... Kirby Ultimate G Bagged Upright Vacuum

The beater brush on my vacuum appears to roll when I turn on the vacuum however, you only hear the actual sound of it on occasion and the vacuum is not vacuuming thread off the floor.

Greetings from GoVacuum,\015\012\015\012Your belt has probably been stretched to a point, the brush no longer spins when it touches the carpet. You probably can turn the machine over, and see the brush spinning, but it's probably stretch ... Eureka Vacuums

Brush will not stop moving when put in upright or bar floor mode. Also red power light doesn't come on when turned on.

Hi Chris,I'm sorry to hear you're having difficulties with your DC28. I'd encourage you to get in touch with us directly, so we can provide further assistance in resolving this issue. Please call our Helpline free on 1-866-693-9766 - or if yo ... Dyson DC28 Animal Bagless Upright Vacuum

LlllSteam vac ws working very well--shilfted to using hand vac on furniture--when I shiftead back to wanting to use the floor vacuum using the 6 brushes and the floor vac system, the r6 rotaty brushes will not turn or function. What do IO havae to do to get them to turn and function? The lever on the side ils set for carpet terrain. What do I do now to get brushed to turn and scrub as they should and did previously. James Yerges 1'630-232-2798 JMYerges&comcast.net

What is the exact model number of that unit. There are several with that name. The only things that it could be are the handle mechanism that activates the brushes or the indicator is not working nad the level that selects the brushes is not working. ... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3225 seconds