Having problems with your Electrolux UltraLux 2000 Bagged Canister Vacuum ?

My power cord will not retract back into the housing< i would like to open the back of the unit but there no screws or bults to due so. How do you open the back of model c151d


Answers :

Try standing vacuum on end, then gently tugging and releasing cord. This generally will retract it.
\015\012There are many problems that can result in disassembly and reassembly by an untrained person, including shock and fire. For those and other reasons, I don't recommend trying this yourself. Take it to the nearest Aerus Electrolux store for repair.
\015\012The back of the vacuum can only be removed by separating the top and bottom portions of the canister. The cord winder will need to be removed and the wires all disconnected. The cordwinder is then taken apart and the cord rewound and set for proper tension for rewinding. If the cord is simply stuck due to having been pulled out too far, this is generally not necessary.
\015\012
\015\012http://www.aerushome.com/storelocator/
Repair Help & Product Troubleshooting for Electrolux UltraLux 2000 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My power cord will not retract back into the housing< i would like to open the back of the unit but there no screws or bults to due so. How do you open the back of model c151d


Try standing vacuum on end, then gently tugging and releasing cord. This generally will retract it.\015\012There are many problems that can result in disassembly and reassembly by an untrained person, including shock and fire. For those and o ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I have a Kenmore Progressive Canister Model # 29612992. I was replacing the sweeper bag, when I opened the lip, the plastic arms was pull out of joint and will not close. I removed the 2 screws under the lid to put back it in place but there I can't remove the plastic molding because there are still screws holding somewhere. Are there tabs instead of screws still hold the molding?


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Found old J.C Penny vacuum cleaner on garage, looks industrial, canister model. It takes intake from the front but just expels it off the back. After opening, I see it needs a bag and a filter, the model is J.C Penny wet/dry 10 gal. MOD-SVP-017 Catalog # 824-4327. Unable to find any info on the web regarding it. Any help??


... Vacuums

I have a sta rite (pentair) cristal high rate sand filter model T-200-BP-1....its leaking water thru the top of the valve, where the valve cover screws on the valve body assembly. it leaks water out where they go together around the screws. Also when i vacuum it, everything that i vacuum gets washed back in the pool when its on the filter position. Also the backwash leaks when its turned 2 the filter position, does it supposed to do that?...the only way i have gotten it to stop is to put a seper


... Vacuums

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi


Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums

I have a model s3765 Hoover Windtunnel and it was no longer suctioning like it used to. I wanted to see if something was stuck in the rollers. I undid the screws at the base 3 of them and now I see there is a pic that do not undo these screws. I am having problems with getting them back in.


If you can post a pic of which 3 screws you are talking about and where you took them out of i can help u get it back together ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have the Sharper Image EV-HD15 Cool Mist Humidier Ultrasonic 1.6 gal humidifier. I purchased it last year. Yesterday I took it apart to clean as per instructions. I feel that I may not have place the round housing (which is secured with 4 screws) back correctly. When I turned the machine on it made a whirring sound. I took the unit apart again and rotated that round piece moving the opening away from the opening on the tower. The whirring sound was reduced but there was still a sou


... Sharper Image Vacuums

We have lost the manual for your Model 75224 can opener. This belongs to my elderly aunt who complains that she can't use it now because the handle was taken off and she can't get it back on. I recall this problem once before, and after looking at the picture in the manual, it was a cinch to put back on. Without the manual, however, I am having no luck.


I entered a search on Google, and I saw several pictures of the Can opener-- would just seeing a picture help?If not-- here is a site that claims to offer the manuals-- You will have to register, and dig into it a bit-- ... Vacuums

The Lifesaver smoke alarm model 1225 is hard wired, no battery and is chirping. I have it pulled out with wires coming out of the back, but can't open the front face to get in to disconnect the wire. Anyone know how to open it up?


Hi, you should be able to grasp it and twist it to open/remove it from the juntion box to expose the 120 volt wires. They do not open like one with a battery type, so twist it I believe CCW to remove it from the box to disconnect the wires. Please be ... Vacuums

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating


... Vacuums

Help! i have a whispertone 300 model 116 28612790. the retractable cord is jammed & i could only get the front part of the canister open that houses the motor, etc. there are only 2 screws to open it & i can't get it off to fix the cord. hope this makes sense. thank you!


Even if you get it apart chances are it needs a new spring but it requires a special tool to get the rubber molding off that separates the top from bottom and sears repair guys and vacuum shops have them. I would take it to a used vac store and get t ... Kenmore 23313 Whispertone Bagged Canister Vacuum

I need to change the retractable cord in a Kenmore Model 116.228.13204 vaccum but can't figure out how to remove the housing. I have removed the bag and the two screws but the top appears to be attached under the foot pedal. How do you release it. Does the foot release pop off somehow to reveal another screw in the back of the housing?


Go to this web site, it gives you complete schematics of your model. This will make it easier to see where all screws are and what you have to remove to get to reel. http://www.searspartsdirect.com/partsdirect Just enter your model # and complete bre ... Kenmore Vacuums

How do i remove the reel cover for my SEARS canister model 116312690 vacuum cleaner. we are unable to move the cord forward or back. We have found two screws, but are still unable to remove the cove


... Kenmore Vacuums

Sears kenmore vacuum model 116 22852600c what type of screws on the bottom back


... Kenmore Vacuums

I have a Miele STB 200-205 turbobrush that no longer spins. What can I do to clean it out, other than open the back with the orange screws?


Probably nothing. You probably have a clog in the dirt path. ... Vacuums

I have a Dirt Devil Featherlite Model 085430. It making a horrible noise and I want to open it up to see if anything is broken or lodged in the motor housing. I've removed all the screws I can find and still can't get the thing apart.


Hi,\015\012\015\012The user manuals in this site may be helpful.\015\012\015\012Best wishes. ... Vacuums

Tafel Steam Iron Model 2820 3.12 104 - switch connections - can you please explain how this is works Iron stoped workin open the back and one of cales to the switch is hanging loose - but can not workout the obvious way to reconnect - can you help by showing me a diagram of the switch mechanism kind regrad


... Vacuums

How to remove the " button cord rewind " from the kenmore progressive model 116-28712790 ?? I need to get to the screw below to open up to get to the motor.


I found the problem... screws on top under the cord rewind bar ... Vacuums

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?


Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

My Panasonic model MC-V6830 works but no suction. I checked and belt was loose, but there is nothing to attach the back of the belt onto. Seems some screws or plastic pully part/parts are missing. What parts do I need to order to fix this vacuum?


... Panasonic Vacuums

I need to open up this Hoover Uprite Runabout deluxe to replace the belt. I dont see any screws to remove to access. Model # U5064-940


You will find them on the bottom of the machine on the brush roll cover. This is the belt you need:Hoover Runabout Deluxe U5064-940 Belt ... Vacuums

My polti 2400 leaks, where can I get a screw driver/ spanner to open up the back to identify the problem


... Polti Vaporetto 2400 Canister Steam Vacuum

I need to get to the internals of the machine in order to retape the electric wire that originates inside. I have removed all of the visible external screws that are keeping the 2 sides together but it still will not open. It is a Euro-Pro vacuum model ep 601. Can you help?


\015\012\015\0121. \015\0121 Lower handle of vacuum and flip\015\012over so that it lies flat on floor upside down.\015\0122. Twist 3 plast ... Euro-Pro Vacuums

Dear Sir: I just purchased a Bissell Rug Shampooer at a garage sale. The only thing I find for a model is on the back and it says Model 1695 there. Nothing on front. It is Navy blue and has a grey tank on it with a smaller one inserted at bottom of the large tank. It has two switches on the back of it and the trigger switch at the handle. The cleaner works, BUT, it does not extract any water back into the tank that is to pick up the dirty water. Could you suggest what I may look at t


... Bissell Vacuums

Where can i buy parts for the model C151D vacuum. any place i checked does not have that model of electrolux listed. i need the power wand attachment. i ordered one that looked like it from sears parts direct but it wasn't the proper one and they do not list the model C151D


Any Aerus Electrolux store. For the one nearest you, check the below link and follow the directions. Keep in mind that if it's too far away, they do ship. If you're close enough, they do deliver.\015\012This model is not the same company tha ... Electrolux UltraLux 2000 Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0572 seconds