Having problems with your electrolux ultralux classic ?

how to get power to the power head on ultralux classic

checked connections. no light comes on. Cannot find a reset button

Answers :

Repair Help & Product Troubleshooting for electrolux ultralux classic

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?


Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

On a Kirby sentria the metal spool sticking out that goes into hose or power head becomes extremely hot and left burns marks on brush tube. It only gets hot when using power head. I checked all adjust


Check the brush roll to be sure it's spinning free too much drag can cause that to get hotter but usually it would break the belt. That spindle will get hot from the friction created by turning the belt and from the motor's heat. They'll just get hot ... Kirby Vacuums

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!


Great. ... Kenmore Vacuums

I have an S3630 Hoover Windtunnel with a Mach 6.1 power head. One of the wheels on the back of the power head broke off. I will need the back under pannel with the back wheels. Where can I get these parts?


... Vacuums

My kenmore model no 116.22512200 canister vacuum power head has no suction & doesn't pick up even though it shows all the signs that it is getting power. The junior power mate works fine.


... Kenmore Vacuums

My samsung quiet storm modl 9068G needs a new brush in the power head. Where can I get one?


... Samsung Quiet Storm 9048R Bagged Canister Vacuum

How to get the power head on a Miracle mate vacuum to work?


... Vacuums

How does the Miele Vacuum Power Nozzle Pinion Gear get taken off and a new one put on? Is it pressed on and just need to pull off or is it screwed off. It is for the SEB217 power head


Greetings,\015\012\015\012What you need to do is screw the Pinion Gear off of the power brush. This can sometimes be tricking, because as I'm sure you're aware, when you twist the pinion gear to try and release it, it also spins the mot ... Miele S318 Bagged Canister Vacuum

I have a kemore progressive canister vacuum and the power head connects enough to the hose where the head accnoledges it's connected and the brush spins BUT i can't get it to lock in so i have


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Power head gets no power - Kenmore 23313 Whispertone Bagged Canister Vacuum


... Kenmore 23313 Whispertone Bagged Canister Vacuum

Miracle mate power head not getting power - Vacuums


Most likely you have a broken wire in the neck assembly, where the wand meets the floor nozzle. To check unplug the cord and remove wand from floor nozzle. On the neck, remove 3 small screws and slide the cover off the back of the neck. You will see ... Vacuums

Broken belt I have a royal canister model 4750 with a broken belt on the power head. I don't know how to disassemble the head to get at the belt.


If you have the power head with the headlight, squeeze the sides of the upper part (almost like a superstructure,) where the headlight is located. It should lift off, allowing access to the screws to get the powerhead apart the rest of the way, and o ... Vacuums

HAVE A RC1400 THAT WON'T RUN. BELIEVE ITS THE POWER CORD BUT CAN'T GET THE VACUUM OPEN . THERE ARE FOUR DEEP HOLES IN THE CASE BOTTOM BUT WHATEVER IS IN THEM , JUST HAS A FLAT ROUND HEAD, NOT PHILLIP'S HEAD OF SLOT. J F


Should be size 15 or 20 torx bit screwdriver required ... Riccar Vacuums

How do you change a belt for the belt on the Royal Part #2-470010-801, Power carpet head attachment for the Royal Classic Power Team canister model #4750?


... Royal Vacuums

Electrolux z8220 - is it possible to get a power head for it?


... Electrolux Centralux Vacuum

Where can I get a new power head and hose for this vacum


The Eureka central vacuums generally have standard inlets. You can use any brand with what you have. The most important thing you will need to decide on is electric vs non-electric. The brands attachments I would recommend are Imperium, Beam, and ... Eureka 1810 Central System Vacuum

Electrolux classic lux power head does not work


... Electrolux UltraLux 2000 Bagged Canister Vacuum

Carbon brushes on ME-48 power head motor worn out. Where can I get replacement brushes? Motor is O 90197X7, Lamb, Model 118173-73 - 240V 50/60Hz


Hi Les,Most sites sell only the motor.Here's a website that includes motor brushes: http://www.kleen-ritecorp.com/search.aspx?IsSubmit=true&searchTerm=lamb+motor&gclid=CIbZ59zwiKgCFQprKgod8W2itQHope you can find the righ ... Filter Queen Vacuums

Where can I get a new power head motor replacement for SE series,original motor GS ELECTRIC 5570-02-1 in UK or Ireland,Thank you,Liam.


... Rainbow E series Canister Wet/Dry Vacuum

The power head just stopped working last night and I can't get it to work on the carpet. What could be the problem?


Did you try setting the power reset button on top? Mine wasn't picking up dirt very well so i took it apart thing the belt was slipping it wasn't. The nozzle was clogged up at the head. i pulled out all this cat hair to see one of the cat toys was lo ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Hi -- I have a Kirby Sentria and it is great except that I am getting no suction at all through the big silver power head. Suction through all the other attachments works well. I haev tried it with the roller belt on and off, and that doesn't seem to make a difference. Am I missing something?? Thanks!


You can take off the power head and look in that whole where the belt is and see if there is a paper towel or something in there clogging it up. Also tug on the belt and make sure it is tight - because if it is loose it is broken and you ... Kirby Vacuums

Have a Bissell Proheat2 will not spray water from the carpet power head but sprays from tools setting Does anyone know how to get water to spray or clean out water


I had this problem. It was small pieces of debris that got into the solution lines and clogged all the nozzles. There is a nozzle for the handheld attachments, one on the front of the machine for spraying spots and two nozzles underneath just behind ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The roller on my power head does not spin consistently. So my vac is not picking up of course. The square end pieces and the rod that goes into the wooden roller seem loose. I tried tightening it but it still is not turning. Can I do a fix with glue or something till I can get a new roller?


... Rainbow E series Canister Wet/Dry Vacuum

My Ultralux 2000 vacuum power head does not work on my machine but does work on a different machine. What are the possilbe problems? I tried replacing the hose with a new one and that didn't help.


It's probably due to bad wiring connections between the wands, hose and wand, or power nozzle and wand. If it came with the Sidekick, try using it on the end of the hose. If not, simply try using the power nozzle on the end of the hose (no wands). ... Electrolux Eureka Easy Clean 2 in 1 Stick and Handheld Vacuum Model 108A 1 ea

Hello Could you tell me where i can get the brush for the power head for my kirby G5, my brushes are almost down to the wood (maybe 4-5mm) i live in melbourne and am happy to order online Cheers and thank you My email is [email protected]


Steelcityvacuum.com ... Kirby Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0522 seconds