Having problems with your Electrolux Vacuums ?

Electrolux model LX vacuum- Problem, ejects empty

\015 Vintage Electrolux model LX vacuum- Problem, ejects empty bag, the blower works very well, but the vacuum suction is very limited. Is this repairable at a reasonable cost?\015

Answers :

The vacuum is doing exactly what it is suppossed to do, on this model, the bag will eject when the suction is reduced due to the pores in the bag becoming clogged by dirt, dust, or fine powder. Try a NEW bag, and **** up less superfine dust such as baby powder or plaster dust that immediately clog the bag. Next, on later model LX's on the bottom of the canister near the bag door is a dial, setting the dial to a higher number will reduce the sensitivity of this automatic bag ejection operation and will allow the vacuum to continue to run until the bag is even more clogged, however, running the vacuum with a fully clogged bag causes the motor to overheat and reduces suction and damages the vacuum. If you have an early model LX, there may have been a "basement and attic" key mounted to the bottom, but often are lost by now and it is used to make such an adjustment. The 1952 model LX was the first with the diaphram automatic bag ejection system and the problem of the bag ejecting too soon was common. An improvement on the model LXI added the control dial with numbers 1 to 6 on it to adjust the sensitivity. I am looking up more info on adjusting a model without the dial because I just picked one up at an estate sale a few days ago and I've heard (some time ago) that the early ones with no dial had a "basement and attic" key that snapped to the bottom of the cleaner to make this adjustment, not sure where it is though and the one I have does not seem to have the key. Will let you know more if I find it! Thanks, I am an Electrolux fan and will use nothing else because I have used so many vacuums but love the convenience of Electrolux design and durability. They have been in my family since my grandparents came to America and are simply the best in my opinion.
Repair Help & Product Troubleshooting for Electrolux Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Electrolux model LX vacuum- Problem, ejects empty

The vacuum is doing exactly what it is suppossed to do, on this model, the bag will eject when the suction is reduced due to the pores in the bag becoming clogged by dirt, dust, or fine powder. Try a NEW bag, and **** up less superfine dust such as b ... Electrolux Vacuums

My Kenmore canister vacuum cleaner model 116.27514700 has unacceptably low suction.It is much less than my older GE Walmart canister vacuum. the 2 filters are very clean and there is no blockage in the hose and the dust collection bag is empty. Is poor suction a characteristic of this model or if not is there a way to fix this problem?

... Panasonic Kenmore Canister Vacuum Vacuum

I have an old Progressive vacuum cleaner that says "Hepa Filter" and "Whisper Belt". Not sure what the model # is. The problem is that the vacuum part itself (the part that touches the floor and rolls over) has ejected its filter that we can see through the little window- it just came out under the rollers under the device... we cannot see how to re-insert this piece of filter which looks like a kind of round, flat grey foam/fabric and clearly goes inside- (top of the part that touches the flo

Check this procedure:\015\012\015\012Unplug the appliance that you will be \015\012changing the filter in.\015\012\011\011\011\011\011\011\011\015\012\015\012\011\011\011\011\011\011\011\011\015\ ... Kenmore 23313 Whispertone Bagged Canister Vacuum

We have a Bissell Proheat 2X (model 8920). The problem we are having is when water/soap is initially released (all settings) it continues to leak out the front water spray nozzles unit the water containers are empty. The vacuum works but can't keep up with the continuous water leaking out. Do you have any idea what is sticking open to allow the continued release of water when the machine is running? Thanks Rick

Return it. It is faulty and should not do that. Mine does not. Does require changing water about evrery 10 minutes but one can see the filth in the water. Also re-clean with plain water over areas that were cleaned to remove all cleaner. Old cleaner ... Bissell 8920 ProHeat 2XTM Upright Vacuum

On-off switch My problem is finding a source for an on-off switch for an electrolux vacuum sweeper model 2100. I have replaced the broken toggle and now the sweeper turns on but only as long as the outside button is depressed. It appears that the on-off switch itself is broken as the switch does not ''hold'' when the toggle is activated. It seems to return to it's ''off'' setting as soon as the toggle is released. What ''holds'' the switch in its ''on'' position? Does it depend only on the on-

Hi Hugh. The 2100 has a rocker switch under neath the button. it is probably broken, or the button has a worn detent spring. If you would like, I could send you a switch kit with the rocker, button, and detent spring enclosed for around 20 dollars ... Vacuums

Helping out someone that has a ECV 1590A model 117A Electrolux central Vacuum. There seems to be a problem with the brushes. I'm looking for a manual or what brushes to get or a new motor. It seems to run fine what it starts.

... Electrolux Vacuums

Hi there, I have an excellent Electrolux (but older) Diplomat LX model which stops when the bag is supposedly full. It''s not full however, but merely 1/4 to 1/3 full. I'd like to reduce the "sensitivity" of the sensor or turn it off altogether. I don't run my vacuum with a full bag, but there's a limit. Please tell me how to address this problem. Thanks very much. Pierre

... Electrolux Vacuums

I have an Electrolux Oxygen 3 Ultra Canister Model No Rel7020. I am having problems with the On/Off Button and the Bare floor/Carpet Brushroll On/off button. The Carpet On/Off will not work at all. In order to turn the vacuum on, I must press a combination of the first two buttons. Is this an electrical issue

You have a problem with the electrical switches. If you are comfortable with this, take apart and double check internal wiring to make sure nothing was frayed, or disconnected. Make sure it is unplugged. If you know how to operate a multimeter, yo ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Hi We have a Electrolux Loopie Pet Lover 1900W Cyclonic Upright Vacuum Cleaner and are having problems emptying it - have slid the lever over to the right as indicated but the dust compartment simply will not come out - is there a knack?? Many thanks

... Electrolux Vacuums

I have an electrolux Z8280 cyclonic twin clean vacuum cleaner 2000w. At the moment the power (blue) and filter light (red) are both flashing at the same time and it won't turn on at all. I have emptied the dirt, checked for blockages, and checked the filters and i still don't know what the problem is :( Can anyone help me? Thanks

It's REALLY easy: https://www.youtube.com/watch?v=HiHwY-lncc0 ... Vacuums

The belt on my vacuum cleaner model 6596 bissel powerforce bagless turbo keeps breaking. As soon as I put on a new belt and start it up the belt snaps. It is the durabelt meant for this vacuum model. Also, my son has been having the same problem with his. He has the same model and same belt. This problem is occurring even after a thourough cleaning.

I would guess you aren't centering the belt correctly, thus it's edge is caught between the brush and another solid object, causing the breakage.\015\012When you get the belt on the the brush and the brush back in place, turn the brush a few ti ... Bissell 6596 Bagless Upright Vacuum

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!

Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.

It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums

Hi good day, I have a Kenmore Grab n Go 12.0AMPS Vacuum cleaner, Model# 116.34722402 & serial#T53601507. The vacuum is now having a problem whereby the rolling brush underneath is not spinning when the vac is on. This has caused it to stop sucking up dust. Could you please advise as to what might be the problem. Thanks in advance for your kind assistance. regards, Clarance

... Kenmore 34722 Grab-N-Go Upright Vacuum

My beater bar does not work on my vacuum. The problem is not in the hose or the attachment, because I connected to another electrolux vacuum and it worked. So the problem must be in the canister.

It's most likely a loose wire in the canister then. I recommend taking the whole vacuum to an Aerus Electrolux store and letting the service tech check it out. They can find out the problem quickly.\015\012Be aware they may try to sell you a ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Vacuum, power nozzle model 1622, electrolux - Electrolux Vacuums

... Electrolux Vacuums

I have a Kirby G4 Vacuum Cleaner - MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I've had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This

Hello,\015\012My educated guess is that it's either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair...\015\012\015\012 ... Kirby G4 Bagged Upright Vacuum

I have a Kenmore canister vacuum - model 25614506. Some time ago, I was not able to turn the vacuum off with the on/off switch, but could still use the vacuum. Turned if off/on by pulling the plug. The other day when I went to plug it in, I heard a pop. Now the sweeper runs but the vacuum cleaner does not **** - no air flow. What could be the problem. The cleaner is only 4 years old.

The motor has an inline fuse ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

I have the Kenmore Model 116.36722600 Vacuum; while cleaning the carpets the vacuum all of the sudden stop working; I didn't smell anything burning; it was almost like someone unplugged it. I checked the rollers and I can move it forward and backwards with no problem. Do you think the motor just burned out? Does this vacuum have a fuse that I can reuse? I love this vacuum and would hate to toss it. thank you

... Vacuums

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v

Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

Replaced cord reel in Electrolux Epic 6000 series and the tempurature light comes on and vacuum will not come on. What is the problem?

1) see the schematic attached: and proceed according. God bless you ... Electrolux Lux 7000 Bagged Canister Vacuum

Hoover Model# U8185-900 Problem: No suction, not engaging Vacuum cleaner roller spins as usual, but there's no suction when trying to vacuum the carpet. Can anyone point me in the right direction? Tha

... Hoover U8185-900 Upright Vacuum

Electrolux vacuum brush not turning problem: was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won't even switch on. Hope you can help

Under the vacuum, there is a guard.\012remove the guard , either by 2 screws or by 2 clips.\012there is a belt under the guard.\012that is connected to the brush.\012the belt need to be replaced. ... Vacuums

Where can i buy parts for the model C151D vacuum. any place i checked does not have that model of electrolux listed. i need the power wand attachment. i ordered one that looked like it from sears parts direct but it wasn't the proper one and they do not list the model C151D

Any Aerus Electrolux store. For the one nearest you, check the below link and follow the directions. Keep in mind that if it's too far away, they do ship. If you're close enough, they do deliver.\015\012This model is not the same company tha ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I have a multifunction robotic auto vacuum cleaner model number XR210. It doesn't seem to be charging when at the docking station. The light is flashing on the docking station as if it was charging, but then I am getting intermittent noises like the vacuum is about to start up, then it beeps and goes silent again. I have emptied the machine. The display does not read 88 as if there is a malfunction, so I'm really not sure what's wrong with it. If I put the vacuum to the docking station the displ

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1036 seconds