Having problems with your Electrolux Vacuums ?

Electrolux model 1521 how to remove motor Steps to remove motor please


Answers :

Open canister compartment, remove rubber side bumpers, then pry off back of cylinder with large screwdriver. The plastic side parts hold cylinder together, at back, pry part over holding tab, then tap side part around tab. Part should slide out. Repeat on other side, and top and bottom housing comes apart. You can now access the motor, cord reel, etc.\015\012\015\012\015\012---------------\015\012This will help. Thanks please keep updated.please do rate the solution\015\012positively .thank you for using fixya.
Repair Help & Product Troubleshooting for Electrolux Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Electrolux model 1521 how to remove motor Steps to remove motor please


Open canister compartment, remove rubber side bumpers, then pry off back of cylinder with large screwdriver. The plastic side parts hold cylinder together, at back, pry part over holding tab, then tap side part around tab. Part should slide out ... Electrolux Vacuums

I have a kenmore vacuum cleaner model # 116.23612. When the hose is attached to the canister it runs, but if you remove the head to just use the hose the unit stops working. Is the motor dead or is there some type of reset or fuse. Could you please tell me how to test this. If so could you please send me instructions on how to replace the motor. Thank you in advance for your help, Tony


... Kenmore Vacuums

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.


Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

Nilfisk GM 90 motor bearing Hi I have replaced the motor bearing on the GM 90 model but having problem with re fitting the turbyne I forgot the sequence it has 2 turbines and 4 2 inch washers Can you please tell me the sequence it is fitted Thanks,,,Ps the motor is 100% ok now Peter


... Nilfisk Vacuums

Removing D720 electrolux motor for replacement


... Vacuums

Removing D720 electrolux motor from machine body


... Vacuums

I was given a model 6591, plugged it in and it worked but didnt "****" and didnt sound right. I turned it off and removed the hose from the back found a badly plugged hose. Removed the hair plug cleaned filters and when I tried to turn it on again. Now the motor will not turn on or even make a noise. I hear there is a fuse that can be blown? How can I find the fuse if there is one? Thank You Ron


The User Guide for the bissell Clearview Power Trak\012\012http://canada.bissell.com/images/UserGuides/3590C.pdf\012 ... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum

I'm looking for a used or reasonable priced motor for my Electrolux LE, series 2100 vacuum. LEE is shown as model but no searches respond to this as a model number. Help. Thanks, Max


Unfortunately, the Electrolux company as such no longer exists. Eureka bought the name "Electrolux" and started making Eurekas with Electrolux stickers on the outside. This makes for some confusion when looking for parts. \015\012\015\012 ... Electrolux Vacuums

I have a Kenmore central vacuum cleaner model number c107 34601. We have emptied the bucket and shaken the filter out to clean it. There is a filter that is filthy so we shook it out into a bag but the cleaner still seems to not have great suction. I notice there is a similar cap to the outlets I plug the central vac hose into on the unit itself that doesn't power the nozzle when used. 1 - what is this for? 2 - Should I somehow remove the entire filter and if so - can you tell me step by step ho


... Electrolux Vacuums

Beater bar not spinning on my dyson animal DC14. Motor turns on and sounds good. My belt is not broken, and still tight on the bar. It looks like another possible belt or gear box between motor and bar. Can anyone please point me to next step?


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Do you know of anywhere I can get an electrolux repair manual for the 1205 model - I need to replace a motor. I have the motor Arthur Gaucher


Don't buy an Electrolux.......... play their one sided game! ... Electrolux Vacuums

I have usha Janome wonder stich model No. 392 , I need a new motor as my previous motor has gone unserviceable and is beyond repair. Please advice me how to get it as i am located in Mumbai


... Vacuums

Need to know price for a new electrolux gensis vaccum cleaner model 1625,canno find price anywhere,and please can u link me to a image/picture of one[how it looks but please tell me price for new one asap


I am pretty sure that model has been discontinued. ... Electrolux Vacuums

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely


The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums

Hi On a Hoover convertable model U4497-900 I'm trying to replace the fan. The old fan cracked, then flew apart. I have the new fan, have the motor assembly removed, but can't seem to get the pulley nut off the motor to replace the fan. Is there a trick to this or should I just try to muscle it? Thanks.


... Vacuums

Hi I have an electrolux vacumm cleaner, super J model. My problem is that the powerhead only works if the switch is in the off position. vacumm motor works in the on position, opposite of each other. Can anyone help? Model 1401


Looks like there's an interchanged wires in your vacuum. Both the motor and the powerhead must go together. Check it up. Leave themotor wiring connection intact. Just tinker and check the powerheadwiring connection . ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Removing motor from electrolux vacuum D725 - Electrolux Vacuums


When viewing from the rear there are small protrusions at 2 & 4 o'clock on one side and 8 & 10 o'clock on the other side of the motor suspension bracket. These are hooked behind an internal ridge in the barrel. On one side the barrel mu ... Electrolux Vacuums

Hi, i was able to get to my electrolux epic series 6500 motor. i know that my bearing is broken inside the motor but i am not able to remove the metal plates around the fans. how can i do so? thanls


You don't. This motor is not designed to come apart, not even by Electrolux service techs. The whole motor has got to be replaced. ... Electrolux Epic 6500 Vacuum

Electrolux power nozzle, model 1692, power cuts on and off. I don't have the manual for it, but I'm trying to remove and clean the brush compartment. I removed the top, but not sure how to get to the brush. I would like to find a manual for it, because it's completely different than the one I use to have.


... Electrolux Vacuums

My bissell model 18Z6 has developed a loud noise and vibration when the brush is running. I have removed the brush assy and cleaned all the hair, etc but still the noise. I ran the brush motor with the belt disconnected and all seemed ok, but of course there was no load on the motor. I suspect a problem with the brush assy bearings or axle or both but I hate to just throw parts at the problem. any suggestions would be greatly appreciated.


... Bissell Vacuums

REMOVING AN ELECTROLUX EPIC 3500 MOTOR


... Electrolux Epic 3500 Vacuum

Need a motor for 35 yr old electrolux model CB cannister shop vac


... Electrolux Vacuums

Removing kenmore vacuum Canister motor cover model 116-27312790


What you need to do is take it apart and look for any carpet peices dug up in there preventing the motor to spin. Also go look for another filter for it and if you google it you can probably get instructions or if you still have the book. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Remove the hose from guardian model C134F aerus electrolux vacuum


... Electrolux Guardian Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0683 seconds