Having problems with your Electrolux Vacuums ?

How do you get into Elecrolux Discovery Upright to replace bely

\015 How do you get into the underneath parts of the Electrolux 1572 Discvery Upright Vacuum to replace the belt that drives the rotating "beater". I took out the 4 screws in bottom plate but it doesn't come off. What's the trick? The vacumm is about 18-20 years old, if that helps.\015

Answers :

Make sure you got all the screws, and then gently pry the cover off, its probably never been off i presume , have some patienc and you'll get it
there may be a fifth screw
Repair Help & Product Troubleshooting for Electrolux Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you get into Elecrolux Discovery Upright to replace bely

Make sure you got all the screws, and then gently pry the cover off, its probably never been off i presume , have some patienc and you'll get itthere may be a fifth screw ... Electrolux Vacuums

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The rotating sweeper on my Electrolux Discovery II isn't turning. Can I assume there is a belt that needs to be replaced? Also, how do I get at the sweeper unit to replace the belt? Finally, where can I find a replacement belt? Thanks!! Dewey

... Electrolux Vacuums

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.

Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums

My brush will not turn on my Bissell 6393 upright bagless vacuum... what is wrong? The belt broke and I replaced it twice... I now have 6 more replacements but the brush still won't rotate. Do I have to get a new brush?

This type of plastic brush roll fails pretty frequently. Hair and other debis gets jammed in the end caps. The hair and debris gets hot which in turn tends to melt the plastic end caps. Remove your brush roll, hold the ends with your fingers and try ... Vacuums

I have a riccar 500 upright and the axel broke in half. The repair shop says it cannot be repaired without replacing the part. WHere can I get the replacement part?

The repair shop should have all the parts needed. However, sometimes the manufacturer stops making some parts. If this is the case, you may need to try to find one at a thrift store or garage sale and cannibalize it. ... Riccar 8955 Upright Vacuum

Trying to replace belt on hoover convertible bagless upright u8188900. belt replace # 38528-049. i have opened vacuum and put belt back on, but it will not get tight enough around the motor gear and the brush spool to be able to activate. am i missing something? mike

... Hoover Vacuums

I have a model # 880 Royal upright that the brush roller ends are bad. Can I get replacements for these? They have the 1/2 in. square ends. What about replacement for the whole roller assembly. The brushes are fairly well worn. Thanks, Arthur Summers

The below site sells the rollers for some models. I'm not sure about yours. The second one, part number R-673273, may fit. Check your brush for a part number. \015\012\015\012 ... Royal Vacuums

Can I get a replacement handle for a hoover wind tunnel upright? It snapped off

That part is available. Includes the handle, cord and "digital" switches. Here's the link:http://www.vacuummedic.com/product.php?id=389Goo ... Hoover UH30010COM Bagged Vacuum

WH5205 upright vacuum power cable replacement. How do you get at the cable connections inside? HELP! :(

... Hoover Vacuums

Bissell 6590 the part I am trying to replace allows you to lower the handle to lay flat to get under furniture and it also allows the handle to stay in the upright postion. i have looked on bissell.com and did not find it-but I will try again. you are super and Thanks allot . Have a super easy day! Michele

It is called the detent lever part # 2030052. If you can't order it from bissell.com or over the phone, most repair shops should be able to order it for you. ... Bissell 6590 CleanView Bagless Upright Vacuum

I have to replace the power cord on my Bissell upright pet hair eraser vacuum because it is damaged from getting run over by the vacuum. Familiar story? Rather than pay a technician a lot of money, I feel I should be able to tackle this myself (went to college and everything). What are some pointers to help me bravely tackle this without the help of a male (no offense guys)?

Of course, its simple.\015\012Use electric tape to make sure the wires never touch, usually a phillips screwdriver will do to uncscrew the machine.\015\012just make sure you line up the cords the right way, positive to +ve and negative to ... Vacuums

I have an Elextrolux Discovery Advantage(upright) . I need to replace the lower hose. Unfortunately the hose comes out of the roller/feeder area fine but I believe it is held in with a screw in the canaster area. My question is this: How can i open the Canaster area - ther is no isable screws

It's simply screwed into the tank. Simply unscrew in a clock-wise direction to remove. To install the new hose, screw in in a counter-clockwise direction. This is opposite the direction normally used for regular screws. \015\012You don't ne ... Electrolux Vacuums

I have a Miele S1721 Powerhouse upright vacuum. When the belt broke I took it into the shop (because when i tried to replace the belt, the tension was so tight I couldn't get it back together!!). When I got it home I DISCOVERED THAT THE HEIGHT ADJUSTMENT DIDN'T WORK anymore. It seems like it's set really hight, because it no longer contacts and brushes the carpet. So it's now useless. I went back to the shop and the tech denied that there was anything wrong. (I didn't have the vac with me). No

Hi\015\012The Miele uprights (S170 and upwards) with the Powerhouse title are ALL Panasonic uprights which have been at one time sold in the UK. Therefore the upright may use TWO drive belts which need to be looked at: Take off the sole plate a ... Vacuums

The brush on my shark upright vacuum is broken where do i get a replacement in montreal quebec

... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

Need to replace 2 belts on the Panasonic MC-UG302 upright hoover and I dont know how to do it. Is it possible to get a brief discription/diagram of fitting belts from somewhere. Tks

... Panasonic Vacuums

How do I get Apart to replace Belt ? - Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Cant get the suction impellar off to replace - Kirby Generation 3 Bagged Upright Vacuum

Shaft has to be spun clockwise. It has reversed thread. If this is not the problem but you just need to somehow hold the field - see instructions HERE. You may ... Kirby Generation 3 Bagged Upright Vacuum

I have a 15 yr old electrolux genesis upright vacuum cleaner that I can't get the roller out, to replace the belt.

Fip it upside down and hit the roller with a malett\015\012\015\012http://evacuumstore.com/c-99-electrolux-belts.aspx?manu ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

I don't know how to replace the belt on my hoover upright. The manual diagram does not display how to get to the motor shaft. (U4617-930)

... Hoover U4707900 Upright Vacuum

Have a Bissell Power Steamer Upright Deep Cleaner - Dirt Livter PowerBrush. Model 1895 The water tank 'must' have been dropped and is cracked too much to use. Can I get a replacement?

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Fan blade is broken in half on my sanitaire upright I have the replacement but cant get the old one off

... Eureka Sanitaire SC4570 Bagged Upright Vacuum

I have replaced the filters and the bag on my Sebo X1 automatic upright but it still has doggy odor that I cannot seem to get rid of. What could be the cause and what can I do?

Hi, Yeah those things are fairly simple and easy to clean, My guess is that its in the hose.\015\012Try a weak solution of bleach and water, pour it in and let soak for 20 mins then rinse well. Dry it throughly in the sun before youe next use. ... Vacuums

I need a replacement belt for Hoover Elite upright vaccum ,model no. U5043-930. What belt do I get?

Hello, \015\012\015\012Your vacuum cleaner originally came with Hoover belt part number 38528027, however Hoover has now discontinued this part number, and replaced this belt with the new belt which is part number 38528040.\015\012 ... Hoover U5227-930 Elite Upright Vacuum

Where can I get a replacement hose for the eureka 431A optima bagless upright vacuum

You could try Espares.co.uk if your u/k ... Eureka 431A Optima Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0779 seconds