Having problems with your Electrolux Vacuums ?

Removing motor from electrolux vacuum D725 - Electrolux Vacuums


Answers :

When viewing from the rear there are small protrusions at 2 & 4 o'clock on one side and 8 & 10 o'clock on the other side of the motor suspension bracket. These are hooked behind an internal ridge in the barrel. On one side the barrel must be expanded at these points and the motor suspension bracket will pop out on that side under the action of the support spring on the end of the motor. There is a special tool for this but it can be achieved as below.
\015\012You will need two screwdrivers smallish but still strong/stiff enough.
At the 3 o'clock position insert one screwdriver from the rear between the barrel & the plastic motor bracket. Lever against the plastic bracket using the tip to expand the barrel outwards. Make sure the screwdriver is inserted far enough until the tip is against the ridge in the barrel. The stiffness of the ridge will keep distortion of the barrel to a minimum. Insert a second screwdriver at the same point. Keep levering the barrel outwards far enough so that the second can be pushed past the ridge holding the barrel outwards. Remove the first screwdriver and lever the barrel outwards working towards the 2 & 4 o’clock positions until the bracket pops out on that side. The other side then will also be free.

Repair Help & Product Troubleshooting for Electrolux Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Removing motor from electrolux vacuum D725 - Electrolux Vacuums


When viewing from the rear there are small protrusions at 2 & 4 o'clock on one side and 8 & 10 o'clock on the other side of the motor suspension bracket. These are hooked behind an internal ridge in the barrel. On one side the barrel mu ... Electrolux Vacuums

Our unit is 7024A Electrolux Oxygen 3 - it seems to work great but suddenly, the head or 'power brush' or whatever it is called - has died. I checked by removing the hose and plugging it directly into the body, but it is still dead. Without that motorized head working, the vacuum is useless. Is it worth replacing? The unit is only about 1 year old and has seen light use only. Very frustrating, since it was the most expensive unit in the store:(


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Motor removal - Electrolux UltraLux 2000 Bagged Canister Vacuum


The body on this unit split apart at the bumpers. You will open the front lid and slide the bumpers and the internal slides forward to separate the panels then the rear housing will drop off. At that point you must gently separate the halves by openi ... Electrolux UltraLux 2000 Bagged Canister Vacuum

My Electrolux Regency Series upright vacuum brush motor does not activate. Cleaned the brush and press reset to no avail. Opened handle switch assembly and checked each wire attached to all three switch settings. Tried disassembling brush assembly but could not pry open after removing all screws.


... Electrolux Vacuums

The motor running the beater bar on ny Electrolux canister vacuum cleaner runs intermittently. It runs about 2 minutes and then cuts off and automatically starts again after a 1 to 2 minute interval. I have tried taking it apart and removing the dust and grit in the beater bar attachment but with no change in operation. What would you suggest?


Check all the wiring connections to make sure they're tight. \015\0121/2. Wiring to power nozzle motor or reset switch is loose.\015\0121. Cord from power nozzle to upper wand. If the plastic portion of the wand is cracked near the co ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall


That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!


Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

I have an electrolux genesis upright vacuum that I bought used about 8 years ago. It has been A great vacuum the best I ever had. I thought the belt had come off so I took it in for repair. They called today and said that the brush rotor motor was bad and it would be around 148.00 dollars to repair. My question is could I buy the part and have my husband replace it or would it be too complicated. Can you still buy an electrolux vacuum comparable to this one and how much are they. I love this vac


... Vacuums

Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.


... Sanyo Vacuums

Electrolux model 1521 how to remove motor Steps to remove motor please


Open canister compartment, remove rubber side bumpers, then pry off back of cylinder with large screwdriver. The plastic side parts hold cylinder together, at back, pry part over holding tab, then tap side part around tab. Part should slide out ... Electrolux Vacuums

I have a nearly 9 year old Electrolux Excellio Z5228 vacuum cleaner. It has recently started cutting out during operation. I cleaned the micro filter (between bag & motor) via brush & hitting against wall & seems / looks quite clean. I washed the gore filter (output from motor to clean the exhaust air) as per instructions, then let to dry. It was very clogged but now very clean. The vacuum clearner still cuts out often. Even after a long rest (say overnight) it still won't start, then ano


... Electrolux Vacuums

Remove old hose Electrolux guardian vacuum - Electrolux Guardian Bagged Canister Vacuum


... Electrolux Guardian Bagged Canister Vacuum

I have a Kirby Dual Sanitronic '50' Vacuum Cleaner I bought in 1966. The motor does not start when I attach the belt lifter of the rug nozzle. When I remove the rug nozzle and detach the belt from the motor fan shaft the motor starts when I depress the nozzle switch and the power switch . Seems like the brushes in the motor are worn out. I do not have a manual for this unit. Can you assist me as to what newer unit is this compatible to and the problem I'm having at present??


... Kirby Vacuums

My electrolux epic 6500sr vacuum has a seized motor. How do I acess the motor to service or change it? There are no obvious screws or clips to open the motor outer case


... Vacuums

How do I gain access to the motor of an Electrolux 2000 canister vacuum. The air intake on the motor must be partially blocked as there is a loss of suction and the motor makes that high pitched whine like it does when you cover the hose with your hand


Dismantling the vacuum probably won't help much, and reassembling can be a bear. \015\012To check the intake, remove bag and look into bottom of bag well. It there's a filter there, remove it and check intake at bottom of bag well. Clear if t ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Miele Cat & Dog vacuum gets VERY hot and is VERY loud. Hose has no restrictions and I have changed the dust compartment (motor) filter and the exhaust filter. It still gets hot when I run it with the top open and all filters removed, so I'm guessing the problem is with the motor. Should I be going into the motor compartment? If so, what am I looking for?


Hi\015\012\015\012The fact that it gets very hot could be due to a number of issues.,but the fact that it started making a very loud noise at the same time suggests that there might be more problems maybe brushes etc.\015\012\ ... Miele S514 Solaris Bagged Canister Vacuum

Beater Bar Belt Removal from Upright Electrolux Vacuum


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783793\015\012Generic problem for all Vacuums\015\012Beater bar Belt Removal from Upright Electrolux...\015\012 ... Vacuums

Removing obstruction from vacuum motor


There should be 2 screws on the top of the base.that will take the cover off remove the belt and on each side of the motor there are 1 or 2 screws that hold the motor onto the base,remove those and you should be able to lift the top half of the vacuu ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Removing motor cover on Panasonic canister vacuum


... Panasonic Vacuums

Removing D720 electrolux motor from machine body


... Vacuums

No suction on my Electrolux central vacuum in all outlets even though motor is running and there is no clog in the hose.


I would start with washing out the ilter really good and letting dry. then try the system. ... Electrolux Central Vacuum

Removing D720 electrolux motor for replacement


... Vacuums

Remove suction motor on rainbow vacuum


How I can open Rainboe E-series Vacuum to change new Air Filter? ... Vacuums

Removing kenmore vacuum Canister motor cover model 116-27312790


What you need to do is take it apart and look for any carpet peices dug up in there preventing the motor to spin. Also go look for another filter for it and if you google it you can probably get instructions or if you still have the book. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Replace vacuum motor on a Electrolux Epic 6500 sr


... Electrolux Epic 6500 Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0753 seconds