Having problems with your Electrolux Vacuums ?

The carpet sweeper on my electrolux stopped working....used it for a little bit and then it just stopped


Answers :

Make sure the brush is cleared and clean, press the reset button, and try again.
\015\012If the motor runs, but the brush doesn't turn, it's likely due to a broken belt. Have it replaced by someone who knows what they're doing.
\015\012I strongly recommend taking it into an authorized shop.
Repair Help & Product Troubleshooting for Electrolux Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The carpet sweeper on my electrolux stopped working....used it for a little bit and then it just stopped


Make sure the brush is cleared and clean, press the reset button, and try again.\015\012If the motor runs, but the brush doesn't turn, it's likely due to a broken belt. Have it replaced by someone who knows what they're doing.\015\012I s ... Electrolux Vacuums

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

My carpet cleaner (bissell proheat plus) is not steaming, dispensing cleaner. Seems like there's a little thingy that should be spinning or turning..... When I work a small area of carpet, it just leaves behind dry blobs of carpet gunk like pet hair. I had to use a carpet sweeper to clean up. FYI - I filled the cleaning fluid container and after trying to clean the carpet, it did empty out but the carpet isn't wet. Any tips? The manual doesn't help.


You need to replace the pump belt. Here is the belt you need:Bissell ProHeat Belt ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bissell pet hair eraser vac, beater brush stops spinning when on carpet of any length, belt is new, hose is securley attached and it will only spin like a carpet sweeper while on carpet?


... Bissell 3920 Bagless Upright Vacuum

Hoover windtunnel Not sure of model number- but brush roller clamps down on carpet being vacuumed and stops spinning regardless of which of the 3 height selections is selected. Can make it work by leveraging the handle down (or back towards me) to keep the cleaning head a little off of the carpet-any suggestions or ideas?


Would suggest the drive belt is stretched and thus is slipping when contact is made with the carpet. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Bissell bagless sweeper sucks up dirt but will not put dirt in the canister cup. It will pickup until it clogs, then it will stop picking up dirt. It will really hold quite a bit of dirt before it stops completely up. Thanks for any help.


I had the same problem, called Bissell over 10 times! They send me 3 plastic inserts for the dirt chamber, not the problem. I solved it by throwing the Bissell away and buying a Eureka bagged vacuum, no more problems. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Hi, I have an electrolux Ambassador and the other day I was vacuuming a fringe carpet and the fringe made the electrolux stop (has happened before) and when I pressed the reset button, the motor is on but the wheel does not spin. Any suggestions?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=678083\015\012Generic problem for all Vacuums\015\012Hi, I have an Electrolux Ambassador\015\012Posted ... Vacuums

Roll brush stops on contact with carpet


There could be a problem witht the tensioned. Take off the top cover and try to see why it isn't pushing the belt when the handle is tilted back. Hopefully the belt is in the proper position, I have seen where the belt was put on the wrong side of ... Vacuums

My electrolux ultra silencer carpet sweeper won't stay on


... Electrolux Vacuums

Electrolux Epic 6500 SR Carpet Sweeper won't go on. Belt good brush moves, bulb looks good, reset red button I'm not sure, works, looks good. Vacuum starts has suction ,


This link is the manualhttp://www.totalvac.com/manuals/electrolux_manual_Epic6500.pdf ... Vacuums

My Bissell spot bot stopped sucking the solution from the container. When we had the problem before we just reseated the container and it started releasing the water/solution. There is a funk little hole that takes water from the container and it seems to move around a bit. We own 3 spot bots, and have had trouble with all of them.


... Bissell 12005 Spot Bot Handheld Vacuum

I have a Eureka Atlantis carpet cleaner and a little water always leaks out of the bottom. Recently, the head of my handheld upholstery cleaner keeps leaking water. How do I get it to stop? Thanks.


... Eureka Atlantis 2595A Upright Wet/Dry Vacuum

The low speed for bare floors won't work at all. The regular speed for vacuuming carpets turns on but spits items back out after a little bit.


There is only one speed on a central vacuum. The power nozzle motor has nothing to do whether or not you have suction. Sounds like you don't have any suction. Unplug your hose from the wall. Start at the unit. Short out the two low voltage wires atta ... Electrolux Central Vacuum

When running the 2100 Electrolux vacuum, it is stopping and starting when pulling or pushing the floor attachment. Seems like the connection at the top of the handle is a little loose or the electric tabs are loose where the hose connects. Any ideas?


Other option is that on the hose end of the electrical connection, you can use an awl on the electrical connections to bend them in slightly so they make good contact when they are automatically plugged in when you connect the wands. HOWEVER, ONLY D ... Electrolux UltraLux 2000 Bagged Canister Vacuum

IRobot stopped picking up larger bits from the carpet. It picks up the dust, but anything larger, it leaves behind. Have changed the filter/brushes. Is there anything else I need to do


Its sounds like the brushes aren't turning. Pull the vacuum and bin off the back and start it and look to see if the brushes are turning. ... iRobot Roomba 560 Robotic Vacuum

Lately, my Kirby Ultimate G has been acting funny. When I push it forward, it's fine, but when I pull it backward on the carpet, the light on the front flickers and the power flutters off an on. I thought it might be the rollers, so tonight I turned the machine over and pulled out the hair that was wrapped around the roller. However, that did not fix the problem. I should probably backtrack a little bit. In the past, I have had problems with the vacuum running over its own power cord.


The cord will need to be replaced with a cord made for the machine, as it has a non-standard plug. The cord cover is held in place with a # 20 Torx screw. Remove the screw and push the cover gently from behind to unlatch it. The handle must also be r ... Kirby Ultimate G Bagged Upright Vacuum

Chatter We have a Kirby Ultimate G. Since we purchased it it bounces across the floor and the level of the sweeper has nothing to do with it. To get it to stop, it has to be at the highest level. The place we bought it, has done nothing to help us. We tried a new beater brush, no help. If I have to use it at it's highest level to sweep my carpet, I might as well not waste my time. ANy suggestions?


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=11557&thid=576381\015\012Chatter\015\012Posted by CANRN on May 06, 2008\015\012We have a Kirby Ultimate G. Since we purcha ... Kirby Ultimate G Bagged Upright Vacuum

I took the hose off to wash it then after letting it dry overnight I put it back on but Im guessing it there was still a little bit of water in between the grooves which ran to bottom of vacuum and now my dyson gets stuck, sort of like a tight hinge. It vacuums fine but I have to keep pushing it down to the carpet with my foot. How can I fix this problem?


Lubrication at the pivot points ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.


Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums

I have a hoover carpet cleaner with the 6 brushes and they have stopped turning i have cleaned the little screen and still no results what may be the problem


I found a copy of the manual on the inter net and was looking through it and it told me how to takemy brush assembly out, so i did that and replaced my brush assembly. it was really easy and only cost 25.00. thanks for the help\015\012 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My electrolux guardian power nozzle took up a corner of a bed sheet and stopped working. I removed the sheet and pushed the sweeper reset and then discovered i had no lights on on the grip/handle. I checked the outlets an they're ok. what to do? please help. thanks, Duane


There is a reset button/switch on top or bottom side in most of the vacuums.Check out if there is one in your model.If no then its a internal problem.When the bed sheet stuck up in the unit.At that time the short happened in the unit and it stopped ... Electrolux Guardian Bagged Canister Vacuum

The beater bar on my dyson DC28 is not turning when it is placed on the carpet. If you lift the sweeper up the beater bar will turn but then when you place it back down on the floor it stops.


... Dyson DC28 Animal Bagless Upright Vacuum

I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.


The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My carpet cleaner will not spray. Maybe a little thru the tool but not enough pressure to SPRAY


Thanks to many others who have posted on similar problems -- water\015\012and/or solution sprays through the handheld tools, but not through the\015\012main machine.As others have suggested, I removed the water\015\012reservoir, which exp ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0793 seconds