Having problems with your Electrolux Vacuums ?

How to replace belt on lux 4000 vacuum? - Electrolux Vacuums


Answers :

The following is for most models of the Aerus Electrolux UR models.
\015\012
\015\012Lay the vacuum on it's front so you can see the bottom of the powerhead as shown below. Befrore going further, hold your hand straight and move your hand across the opening for the brush. If the bristles don't make good contact, the brush also needs replaced.
\015\012Remove the four screws. Using a flathead screwdriver, place it into the two rectangle openings (shown with red arrows) near the wheels and gently pry on tab to release the top of the power head.
\015\012
\015\012
\015\012rogerpotts_5.jpg\015\012
\015\012Flip machine over and gently lift back of cover which will release the front. Lift off and set aside.
\015\012
\015\012This is what you should see. Remove the two screws at the ends of the brush. Check carefully how the ends of the brush fit in. Gently lift out brush. This is a good time to clean entire interior of the power head. Install new belt over motor shaft and teeth of brush: set brush into place. Insert screws. Check tension of the belt.
\015\012rogerpotts_6.jpg\015\012
\015\012Replace cover of power head, being sure to settle front in just beneath the lip of the front of the base first. Press down until it "clicks" into place. Turn machine over and insert and tighten screws.
Repair Help & Product Troubleshooting for Electrolux Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to replace belt on lux 4000 vacuum? - Electrolux Vacuums


The following is for most models of the Aerus Electrolux UR models.\015\012\015\012Lay the vacuum on it's front so you can see the bottom of the powerhead as shown below. Befrore going further, hold your hand straight and move your hand a ... Electrolux Vacuums

I have an electrolux genesis upright vacuum that I bought used about 8 years ago. It has been A great vacuum the best I ever had. I thought the belt had come off so I took it in for repair. They called today and said that the brush rotor motor was bad and it would be around 148.00 dollars to repair. My question is could I buy the part and have my husband replace it or would it be too complicated. Can you still buy an electrolux vacuum comparable to this one and how much are they. I love this vac


... Vacuums

Replace belt on powerhead of electrolux 9000 - Electrolux Compact Canister Vacuum Powerhead Belt


... Electrolux Compact Canister Vacuum Powerhead Belt

Looking for new belt for my electrolux guardian canister vacuum power nozzle marked model n106m . have been unasble to locate an appropriate belt replacement. Any suggestions?


This company is now known as Aerus. If you can't find their listing in the local yellow pages, follow the instructions on the folloing site.\015\012\015\012 ... Electrolux Guardian Bagged Canister Vacuum

Replace powercord for lux 6000 - Electrolux Cleaner Lux 6000 Vacuum


... Electrolux Cleaner Lux 6000 Vacuum

Replace belt electrolux vacuum - Vacuums


... Vacuums

Replace drive belt lux commercial vacuum - Vacuums


... Vacuums

Little lux belt - Electrolux Little Lux Bagged Handheld Vacuum


... Electrolux Little Lux Bagged Handheld Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t


The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

How to replace belt on lux 4000 vacuum


... Electrolux Vacuums

How to replace belt - Electrolux Precision Brushroll Clean Bagless Upright Vacuum EL8805A


... Electrolux Precision Brushroll Clean Bagless Upright Vacuum EL8805A

Belt replacement electrolux z8280 - Vacuums


... Vacuums

How do you replace vacuum belt on a electrolux regency series upright model?


You can access the belt from underneath the unit, where the brush is. Just remove the screws that hold the cover plate in place and lift the plate off. When replacing the bottom, make sure you get the front tabs into the slots before you press the ... Vacuums

Hi , I have replaced the electric cord on Electrolux Lux Royal vacuum , but the rewind that retracts the cord does not pull it in . The coil spring looks ok but it will not pull the cord back in , any suggestions please . Thanks Dave Ryder


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=564353\015\012Generic problem for all Vacuums\015\012Hi, I have replaced\015\012Posted by dryder on May 02, 2008 ... Vacuums

I have a 15 yr old electrolux genesis upright vacuum cleaner that I can't get the roller out, to replace the belt.


Fip it upside down and hit the roller with a malett\015\012\015\012http://evacuumstore.com/c-99-electrolux-belts.aspx?manu ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Electrolux Z61 Handheld Vacuum Cleaner. Brush heads have stopped turning. Have removed screws but the casing seems to be still fixed together by a plastic joint which looks as if it will break if forced. How can I check that the belt is OK, and if it isn't, how do I open the cleaner to replace it?


... Electrolux EUK71B Bagless Handheld Vacuum

Hello. I have an electrolux glider upright bagless vacuum cleaner (UK model) who's brushes do not rotate any more. I'm guessing that I need to replace the drive belt but I have no idea where to start. I would appreciate any tips. thanks


Hello! There are two solutions to this as the Glider model you speak of could be the more old fashioned type where screws on the bottom foot plate (ie where the spinning brush sits) have to be undone in order to get to the drive belt.\015\012 ... Electrolux Vacuums

I just bought a good Sears Kenmore Progressive 300 upright vacuum (116.38812891) today at a garage sale for five bucks. I left my relic Electrolux with the new owners of my former home during a recent relocation. In the interim I bought a Bissel 3750H which I do not care for, and borrowed a Eureka 7685 AU which performs somewhat better. I cleaned up the Kenmore, and though it seems to run well, noticed the drive belt is showing signs of degeneration. I would like to replace it, but was unable t


... Vacuums

Replacing the belt on an Electrolux Advantage vacuum


I took care of it. Thanks for checking. ... Electrolux Lux 7000 Bagged Canister Vacuum

Lux classic model u155d replace belt - Vacuums


... Vacuums

I have an old Hoover vacuum model # U5035-930. The belt broke and I tried replacing the belt myself. I couldn't stretch the belt to attach it to the motor pully. It was belt # 38525-027 M6. Which I got from the previous owner. I took it to a vacuum repair place and he replaced it with belt # 38528-027 J4. I cannot find this belt anywhere.


... Vacuums

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel


The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

The Panasonic MC-V7515 has two belts. The local vacuum repair guy says he only has a part number for the drive belt, which is UB-9. How do I find a replacement for the other belt, the one which directly drives the beater bars? By the way, this vacuum has great suction, but otherwise is far inferior to my previous Panasonic vacuums. The cheaper models aren't a good buy--stick with the more expensive models.


... Panasonic MC-V7515 Bagged Upright Vacuum

The rotating sweeper on my Electrolux Discovery II isn't turning. Can I assume there is a belt that needs to be replaced? Also, how do I get at the sweeper unit to replace the belt? Finally, where can I find a replacement belt? Thanks!! Dewey


... Electrolux Vacuums

I accidently ran over a sock while vacuuming underneath my bed and the belt broke (brush does not rotate now). I've always changed the belts in my vacuum cleaners, but the Healthy Home manual states that I need to bring it into a shop so that a professional repairman can change it. I find this ridiculous and now wish that I never bought it. How do I change the belt myself? PS I have already bought a replacement belt.


... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1452 seconds