Having problems with your Electrolux Vacuums ?

We are trying to fix our vacuum and we can not get the cover off to see what the problem is. The Carpet mode is not working and the motor is not running. Any advice? Thanks Katie

Answers :

Hi, this could be many things. If I had more info. on the make and model it would help. It could be anything from a burnt out motor or a simple reset button. Whay happened when it stopped cold be valuable info. for me. Please gt back to m with the make and model,ie. upright or cannister. Chris
Repair Help & Product Troubleshooting for Electrolux Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We are trying to fix our vacuum and we can not get the cover off to see what the problem is. The Carpet mode is not working and the motor is not running. Any advice? Thanks Katie

Hi, this could be many things. If I had more info. on the make and model it would help. It could be anything from a burnt out motor or a simple reset button. Whay happened when it stopped cold be valuable info. for me. Please gt back to m with the ma ... Electrolux Vacuums

Hoover F7431-900 my carpet shampooer/steam vac was working fine until the brushes at the bottom of it just miraculously stopped working. they wont spin at all. Is this a motor problem? perhaps a water flow problem? please write back if you can be of any help. thanks

If the screen is not dirty, and the flapper valve to the turbine inlet is open, then the problem is mostly a stuck turbine impeller. The turbine impeller on my F7431-900 has seized TWICE!! The shaft for the turbine is not made of stainless steel, t ... Hoover F7431-900 SteamVac Vacuum

After using switch to go from floor to carpet, noticed the roller brush not working, and therefore the self-propelled feature also not working. Replaced what I thought was the problem, a loose belt, but still does not work. Motor runs and there is suction...???

... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

We have two of these vacuums and both of them have experienced the same problems. First the floor heighth adjustment doesn't work and now neither one will pick up on either carpet or floor when in the brush/floor mode. They both seem to work with the suction hose function. We have removed the back panel to see if there was an obstruction but it was clear. We have changed the bag and the small filter (not the HEPA filter) all to no avail. What else can we do? We are desperate to use our vacu

Did you check the powerhead for obstructions? With a bend in the tube just below where the hose connects, this is a common spot for clogs. To check, detach hose and drop a coin in the hole. If it doesn't drop through, a blockage is present. Use t ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum

Hoover Jet and Wash 1500w S6254 001. Used once with great difficulty as assembly and use instructions are hard to follow.Now will not work as carpet shampooer at all, although assembly is correct as far as I can see and both motor and pump appear to be working and I am using the recommended cleaning fluid.Hoover website is no use at all in solving the problem.No cleaning fluid is being drawn up from the tank in to the cleaning fluid hose.There is suction from the suction hose so the problem appe

I am having the same prob my uncle got me one i cant find the manual anywhere to set it up the prob i have is where does the handle to make the water go out connect tooo ??? on the main pipe that sucks it back up i have tried every which way but not ... Vacuums

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!

Great. ... Kenmore Vacuums

My Kenmore canister model (116) 26212601 works in hard-surface mode (basic suction), but the brush won't spin for carpets, and when I try to turn it on, it makes a whiny sound and then turns off as it does when I need to press the overload button. I looked inside a bit, and the belt isn't broken--it seems fine. So not sure what the problem is. Thanks for any help.

... Kenmore 27815 Bagged Canister Vacuum

I have the Kenmore Model 116.36722600 Vacuum; while cleaning the carpets the vacuum all of the sudden stop working; I didn't smell anything burning; it was almost like someone unplugged it. I checked the rollers and I can move it forward and backwards with no problem. Do you think the motor just burned out? Does this vacuum have a fuse that I can reuse? I love this vacuum and would hate to toss it. thank you

... Vacuums

I have a Bissell proheat2 turbo carpet cleaner. The power brushes have stopped rotating. The brushes are free to turn by hand . The motor works fine with good suction. What is the problem ?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.

Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem. ... Vacuums

Carpet vacuum attachment quit working after sucking up a bedskirt. Bedskirt has been removed but carpet attachment will not work. My old vacuum had a reset button on the carpet attachment for use when the carpet attachment sucked up something and turned off. Does the Hoover have such a feature, and, if so, where is it? If not, how do I fix the problem and how do I keep it from recurring? Model # S3765-040. Serial # 100700081298. Purchased 2/08.

I have a Hoover Conquest approx. 4 yrs old. The turbo head is not working Model No. PB4 230-240V AC 50Hz 200w CS4901N (N127) I have been trying to locate another one or another one similiar to fit my machine ... Hoover Vacuums

My filter queen majestic quit working. I opened up the unit to see what was wrong and I did not immediately notice anything wrong. Upon furter examination I noticed one of the traces on the printed circuit card was burnt. I used a soldering iron to "bridge the trace and it appeared to fix the problem for a while. Now it has stopped working again, and when I jumper the trace to run the motor it seems to work. Should I just replace the card? Or is there a more serious problem with too much current

I recommend replacing the card. Soldering involves the risk of further damaging the card, so it would be useless anyway. Why waste valuable time?\015\012There is a possibility of the motor overheating, generally due to a blockage in the airfl ... Filter Queen Majestic Canister Vacuum

Suction only works using the hand held mode, there is no suction when try to use on carpet mode,

There must be a clog in either the hose, dirt inland by the brush roll, or bad filters. If you have suction at the end of the hose, then look lower all the way to the brush roll. ... Vacuums

My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?

Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

The beater bar motor doenst work when i push the bar button the bar button doesnt light up like power button how can i test bar motor or bar switch or what is the common problem wiyh this model I have 2 that dont work the same way

If it do not work ...and you already are on the second one that behaved in the same way it may be a problem with the power in your place and the cause it may be the main fuse...Im not sure where is located in this model but it has to be near the powe ... Vacuums


This unit uses a turbine assy to turn the brushes. The brushes could have something jamming them. Remove the brush unit, it is held on 2 spring hooks 1 on each side. The brush unit is driven thru a 1/4" square post, only one brush is driven and it dr ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920

The brushes will only work if the handle is released and the ProHeat vacuum is running . There is a micro switch inside the lower handle that switches on the DC carpet brush motor. The DC power for the motor comes from a Bridge Rectifier on the PC ... Bissell Vacuums

Suction problem I have a Hoover Widepath Fold Away, 12 amp motor vacuum cleaner and the problem I am having is every time I vacuum, the vacuum gets clogged up with carpet. I am probably only able to do one stroke then it gets clogged and I have to stop and unclog it or it spits it out on the carpet. This is very frustrating and I don't get much vacuuming done. Please can you help me. Thank you. Gwen email is [email protected]

Get rid of the carpet its shredding and falling apart.no sence in vacuuming old rotten carpet.or try using a vacuum without a brush roller and just suction ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920

You need to change the belt(s). You can find the belts for this model here. http://www.vacbelts.com/bissell-proheat-belt-combo-pack.htm ... Bissell 8910 ProHeat Clear View Upright Vacuum

I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?

... Kenmore 34722 Grab-N-Go Upright Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?

... Vacuums

I have an animal dyson. The front nose dives into the carpet when moving the dyson in the forward motion, fine when pulling back. A huge amount of effort is required to move it forward. Took it to a technician and he said he could find nothing wrong. He had only short nap carpet for test. Works fine on short nap, if the carpet nap has any lenght to it like shag, the dyson severly nose dives. It's like the nose is sucked into the carpet. This problem just occured after the wife used the ho

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Shopvac 90L400 quit working (4 years old). Thought the switch was bad but not the problem. I read that there is a fuse link in the motor that frequently burns up. I tried to take motor apart but not sure of the process. I was able to get to the motor but cannot pull it out of the armature. It appears I have to take the aluminum blower unit off the shaft (it appears to be pressed on with a retaining washer). Do I have to take it off to pull the shaft and motor assembly out? Is that where the fuse

By pass the switch and take power right to the motor leads.. that should tell you if the motor is ok.. have not seen fuse link on a vac motor.. graingers has new motors, but not inexpensive ... Vacuums

Dead motor? My 8 year old Miele S251i has worked fine, until I was recently vacuuming and moved the plug from one outlet to another. When I restarted the vacuum, it made rrrrr.....rrrrrr....rrrrr noises and smelled like something was burning. I turned it off, and it's shown no signs of life since. Sound like a motor problem? I've taken the cover off and looked at the cord and seen the motor, nothing looks obviously wrong, but I'm also not mechanical.

... Miele S251 Flamenco II Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0783 seconds